MediaWiki API result

{
    "batchcomplete": "",
    "continue": {
        "gapcontinue": "Readiness_-_AXK_Engine_Code",
        "continue": "gapcontinue||"
    },
    "warnings": {
        "main": {
            "*": "Subscribe to the mediawiki-api-announce mailing list at <https://lists.wikimedia.org/mailman/listinfo/mediawiki-api-announce> for notice of API deprecations and breaking changes."
        },
        "revisions": {
            "*": "Because \"rvslots\" was not specified, a legacy format has been used for the output. This format is deprecated, and in the future the new format will always be used."
        }
    },
    "query": {
        "pages": {
            "1867": {
                "pageid": 1867,
                "ns": 0,
                "title": "Readiness - APB Engine Code",
                "revisions": [
                    {
                        "contentformat": "text/x-wiki",
                        "contentmodel": "wikitext",
                        "*": "=== Manually Generating Readiness ===\n\n\n\n* <u>Ignition ON and Engine <b>OFF</b></u><br>\n\n\n\n''Reading and clearing fault codes''<br>\n\n'''[Select]'''<br>\n'''[01 - Engine]'''<br>\n'''[Fault Codes - 02]'''<br>\n'''[Clear Codes -05]'''<br>\n'''[Done, Go Back]'''<br>\n\n\n''Throttle Body Alignment''<br>\n\n'''[Measuring Blocks - 08]'''<br>\nSelect group 060<br>\n'''[Go]'''<br>\n'''[Switch to basic settings]'''<br>\nOnce you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.<br>\n'''[Switch to Meas. Blocks]'''<br>\n\n\n''Transmission kickdown (applies to Auto Trans vehicles only!)''<br>\n\nSelect group 063<br>\n'''[Go]'''<br>\n'''[Switch to basic settings]'''<br>\nOnce you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.<br>\n'''[Switch to Meas. Blocks]'''<br>\n\n\n'''[Done, Go Back]'''<br>\n'''[Close Controller, Go Back]'''<br>\n\n\n\n* <u>Ignition ON and Engine <b>ON</b> at idle</u><br>\n\n\n''Fuel leakage test''<br>\n\n'''[Select]'''<br>\n'''[01 - Engine]'''<br>\n'''[Measuring Blocks - 08]'''<br>\nSelect group 071<br>\n'''[Go]'''<br>\n'''[Switch to basic settings]'''<br>\nLeave it in Basic Settings until the fourth field reads Syst.OK<br>\n'''[Switch to Meas. Blocks]'''<br>\n\n\n''Evap purge test''<br>\n\nSelect group 070<br>\n'''[Go]'''<br>\n'''[Switch to basic settings]'''<br>\nLeave it in Basic Settings until the fourth field reads EVAP OK<br>\n'''[Switch to Meas. Blocks]'''<br>\n\n\n''A/F control test''<br>\n\nSelect group 107<br>\n'''[Go]'''<br>\n'''[Switch to basic settings]'''<br>\nLeave it in Basic Settings until the fourth field reads Syst.OK<br>\n'''[Switch to Meas. Blocks]'''<br>\n\n\n\n* <u>Ignition ON and Engine <b>ON between 1800 and 2200 rpm</b></u><br>\n\n\n\n''O2 sensor heater test''<br>\n\nSelect group 041<br>\n'''[Go]'''<br>\n'''[Switch to basic settings]'''<br>\nLeave it in Basic Settings until there are kOhm readings in the first and third fields<br>\n'''[Switch to Meas. Blocks]'''<br>\nSelect group 042<br>\n'''[Go]'''<br>\n'''[Switch to basic settings]'''<br>\nLeave it in Basic Settings until there are kOhm readings in the first and third fields<br>\n'''[Switch to Meas. Blocks]'''<br>\n\n\n\n* <u>Ignition ON and Engine <b>ON at idle</b></u><br>\n\n\n\n''Post-cat O2 sensors readiness test''<br>\n\nSelect group 036<br>\n'''[Go]'''<br>\n'''[Switch to basic settings]'''<br>\nLeave it in Basic Settings until you see B1-S2 OK in the first field and B2-S2 OK in the third field<br>\n'''[Switch to Meas. Blocks]'''<br>\n\n\n\n* <u>Ignition ON and Engine <b>ON between 1520 and 2280 rpm</b></u><br>\n\n\n\n''Pre-cat O2 sensors response time test''<br>\n\nSelect group 034<br>\n'''[Go]'''<br>\n'''[Switch to basic settings]'''<br>\nLeave it in Basic Settings until the fourth field reads B1-S1 OK<br>\n'''[Switch to Meas. Blocks]'''<br>\nSelect group 035<br>\n'''[Go]'''<br>\n'''[Switch to basic settings]'''<br>\nLeave it in Basic Settings until the fourth field reads B2-S1 OK<br>\n'''[Switch to Meas. Blocks]'''<br>\n\n\n\n* <u>Ignition ON and Engine <b>ON at idle</b></u><br>\n\n\n\n''O2 sensor control test''<br>\n\nSelect group 037<br>\n'''[Go]'''<br>\n'''[Switch to basic settings]'''<br>\nLeave it in Basic Settings until the fourth field reads Syst. OK<br>\n'''[Switch to Meas. Blocks]'''<br>\nSelect group 038<br>\n'''[Go]'''<br>\n'''[Switch to basic settings]'''<br>\nLeave it in Basic Settings until the fourth field reads Syst. OK<br>\n'''[Switch to Meas. Blocks]'''<br>\n\n\n\n''Post-cat O2 sensor aging test''<br>\n\nSelect group 043<br>\n'''[Go]'''<br>\n'''[Switch to basic settings]'''<br>\nLeave it in Basic Settings until the fourth field reads B1-S2 OK<br>\n'''[Switch to Meas. Blocks]'''<br>\nSelect group 044<br>\n'''[Go]'''<br>\n'''[Switch to basic settings]'''<br>\nLeave it in Basic Settings until the fourth field reads B2-S2 OK<br>\n'''[Switch to Meas. Blocks]'''<br>\n\n\n\n* <u>Ignition ON and Engine <b>ON between 1880 and 2280 rpm</b></u><br>\n\n\n\n''Catalytic converter test''<br>\n\nSelect group 046<br>\n'''[Go]'''<br>\n'''[Switch to basic settings]'''<br>\nLeave it in Basic Settings until the fourth field reads CAT B1 OK<br>\n'''[Switch to Meas. Blocks]'''<br>\nSelect group 047<br>\n'''[Go]'''<br>\n'''[Switch to basic settings]'''<br>\nLeave it in Basic Settings until the fourth field reads CAT B2 OK<br>\n'''[Switch to Meas. Blocks]'''<br>\n\n\n\n* <u>Ignition ON and Engine <b>ON at idle</b></u><br>\n\n\n\n''Secondary air injection test (applies to Auto Trans vehicles only!)''<br>\n\nSelect group 077<br>\n'''[Go]'''<br>\n'''[Switch to basic settings]'''<br>\nLeave it in Basic Settings until the fourth field reads Syst. OK<br>\n'''[Switch to Meas. Blocks]'''<br>\nSelect group 078<br>\n'''[Go]'''<br>\n'''[Switch to basic settings]'''<br>\nLeave it in Basic Settings until the fourth field reads Syst. OK<br>\n'''[Switch to Meas. Blocks]'''<br>\n'''[Done, Go Back]'''<br>\n\n\n''Checking Readiness''<br>\n'''[Readiness]'''<br>\nMake sure none of the fields say Failed or Incomplete<br>\n'''[Done, Go Back]'''<br>\n'''[Close Controller, Go Back]'''<br>\n\n\n\n<i>You're done! </i><br>"
                    }
                ]
            },
            "1869": {
                "pageid": 1869,
                "ns": 0,
                "title": "Readiness - APB Engine Code-without-MB",
                "revisions": [
                    {
                        "contentformat": "text/x-wiki",
                        "contentmodel": "wikitext",
                        "*": "=== Manually Generating Readiness ===\n\nImportant: This procedure calls for the use of the Basic Settings function in several different groups. It is not advisable to scroll between groups in Basic Settings since you may go into groups that have an undesired effect. Instead, it is HIGHLY recommended that you manually enter in the next group number and hit '''[Go]''' instead of scrolling.<br>\n\n\n<ol>\n* <u>Turn the ignition switch on but do <b>NOT</b> start the engine</u> <br>\n<br>\n  <li>''Reading and clearing fault codes''<br>\n'''[Select]'''<br>\n'''[01 - Engine]'''<br>\n'''[Fault Codes - 02]'''<br>\n'''[Clear Codes -05]'''<br>\n'''[Done, Go Back]'''<br>\n<br>\n\n<li>''Throttle Body Alignment''<br>\n'''[Basic Settings - 04]'''<br>\nSelect group 060<br>\n'''[Go]'''<br>\nOnce you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.<br>\n<br>\n\n<li>''Transmission kickdown <u>(applies to Auto Trans vehicles only!)</u>''<br>\nSelect group 063<br>\n'''[Go]'''<br>\nOnce you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.<br>\n<br>\n\n<li>'''[Done, Go Back]'''<br>\n'''[Close Controller, Go Back]'''<br>\n<br>\n* <u>Start engine and let it idle</u><br>\n<br>\n\n<li>''Fuel leakage test''<br>\n'''[Select]'''<br>\n'''[01 - Engine]'''<br>\n'''[Basic Settings - 04]'''<br>\nSelect group 071<br>\n'''[Go]'''<br>\nLeave it in this group until the fourth field reads Syst.OK<br>\n<br>\n\n<li>''Evap purge test''<br>\nSelect group 070<br>\n'''[Go]'''<br>\nLeave it in this group until the fourth field reads EVAP OK<br>\n<br>\n\n<li>''A/F control test''<br>\nSelect group 107<br>\n'''[Go]'''<br>\nLeave it in this group until the fourth field reads Syst.OK<br>\n<br>\n* <u>Increase and hold engine speed between <b>1800 and 2200 rpm</b></u><br>\n<br>\n\n<li>''O2 sensor heater test''<br>\nSelect group 041<br>\n'''[Go]'''<br>\nLeave it in this group until there are kOhm readings in the first and third fields<br>\nSelect group 042<br>\n'''[Go]'''<br>\nLeave it in this group until there are kOhm readings in the first and third fields<br>\n<br>\n* <u>Take your foot off the accelerator and allow the engine to <b>idle</b></u><br>\n<br>\n\n<li>''Post-cat O2 sensors readiness test''<br>\nSelect group 036<br>\n'''[Go]'''<br>\nLeave it in this group until you see B1-S2 OK in the first field and B2-S2 OK in the third field<br>\n<br>\n* <u>Increase and hold engine speed between between <b>1520 and 2280 rpm</b></u><br>\n<br>\n\n<li>''Pre-cat O2 sensors response time test''<br>\n<br>\nSelect group 034<br>\n'''[Go]'''<br>\nLeave it in this group until the fourth field reads B1-S1 OK<br>\nSelect group 035<br>\n'''[Go]'''<br>\nLeave it in this group until the fourth field reads B2-S1 OK<br>\n<br>\n* <u>Take your foot off the accelerator and allow the engine to <b>idle</b></u><br>\n<br>\n\n<li>''O2 sensor control test''<br>\nSelect group 037<br>\n'''[Go]'''<br>\nLeave it in this group until the fourth field reads Syst. OK<br>\nSelect group 038<br>\n'''[Go]'''<br>\nLeave it in this group until the fourth field reads Syst. OK<br>\n<br>\n\n<li>''Post-cat O2 sensor aging test''<br>\nSelect group 043<br>\n'''[Go]'''<br>\nLeave it in this group until the fourth field reads B1-S2 OK<br>\nSelect group 044<br>\n'''[Go]'''<br>\nLeave it in this group until the fourth field reads B2-S2 OK<br>\n<br>\n* <u>Increase and hold engine speed between between <b>1880 and 2280 rpm</b></u><br>\n<br>\n\n<li>''Catalytic converter test''<br>\nSelect group 046<br>\n'''[Go]'''<br>\nLeave it in this group until the fourth field reads CAT B1 OK<br>\nSelect group 047<br>\n'''[Go]'''<br>\nLeave it in this group until the fourth field reads CAT B2 OK<br>\n<br>\n* <u>Take your foot off the accelerator and allow the engine to <b>idle</b></u><br>\n<br>\n\n<li>''Secondary air injection test (applies to Auto Trans vehicles only!)''<br>\nSelect group 077<br>\n'''[Go]'''<br>\nLeave it in this group until the fourth field reads Syst. OK<br>\nSelect group 078<br>\n'''[Go]'''<br>\nLeave it in Basic Settings until the fourth field reads Syst. OK<br>\n'''[Done, Go Back]'''<br>\n<br>\n\n<li>''Checking Readiness''<br>\n'''[Readiness]'''<br>\nMake sure none of the fields say Failed or Incomplete<br>\n'''[Done, Go Back]'''<br>\n'''[Close Controller, Go Back]'''<br>\n</ol>\n<br>\n<i>You're done! </i><br>"
                    }
                ]
            }
        }
    }
}