View source for Immobilizer III Key Matching (Cluster)

__FORCETOC__
This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with Immobilizer III.

== Determining IMMO-ID & VIN ==

'''[Select]'''<br>
'''[17 - Instruments]'''<br> or in vehicles with separate Immobilizer '''[25 - Immobilizer]'''<br>
'''[Meas. Blocks - 08]'''<br>
Look at the first "Extra" field.
If you see something like: "Immo-ID VWZ7Z0W0648696" then you've got Immo-II (or maybe even Immo-1 in earlier non-US models).

If you see something like "WVZKB58001H231169 VWZ7Z0W0648696" then you've got Immo-III. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.
'''[Close Controller, Go Back - 06]'''<br>

---OR---

'''[Select]'''<br>
'''[25 - Immobilizer]'''<br>
'''[Meas. Blocks - 08]'''<br>
Select Block 081.<br>
'''[Go!]'''<br>
''The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.''.<br>
'''[Done, Go Back]'''<br>
'''[Close Controller, Go Back - 06]'''<br>


== Key Matching ==

'''<u>Prerequisites:</u>'''<br>
* While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.''
* Battery voltage at least 12.5 V.<br>


'''[Select]'''<br>
'''[25 - Immobilizer]'''<br>
'''[Meas. Blocks - 08]'''<br>
Select Block 002.<br>
'''[Go!]'''<br>
''The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.''<br>
''You can check each key in this manner.''


Select Block 003.<br>
'''[Go!]'''<br>
''Make sure the shown lock times in field 1, 2 and 3 are '''0''' (each field represents a time in minutes).''<br>
* ''If the lock times are NOT '''0''':''
** ''Do NOT switch off the ignition!''
** ''Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-3.''
'''[Done, Go Back]'''<br>


'''[Security Access - 16]'''<br>
''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''
* '''4-digit PIN'''
** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
* '''7-digit PIN'''
** '''[Use 7-digit PIN/SKC]'''
** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
** '''[OK]'''
** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
'''[Do it!]'''<br>


'''[Adaptation - 10]'''<br>
Enter 001 in "Channel Number".<br>
'''[Read]'''<br>
''The "Stored Value" is the number of keys currently matched.''<br>
Enter a "new value" corresponding to the total number of keys to be matched,  including any existing keys.<br>
''The old keys are automatically beeing cleared.''<br>
'''[Save]'''<br>
'''[Done, Go Back]'''
'''[Close Controller, Go Back - 06]'''


* ''Repeat the following steps until all keys have been matched:''<br>
**''Switch ignition off and remove key.''<br>
**''Insert next key to ignition and switch ignition on again.''<br>
**''The warning light for the Immobilizer will light up for ~2 seconds, then go out Switch ignition off and remove key.''<br>

'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''