View source for Throttle Body Alignment (TBA)

'''Throttle Body Alignment (TBA)'''
<br>
<br>
Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk. As always, you should refer to a Factory Repair Manual for your vehicle!
<br>
<br>
This procedure details how to perform a Throttle Body Alignment (TBA) on many VW/Audi vehicles. This procedure cycles the motorized throttle body through various states (idle, part throttle, WOT) to relearn their positions. Some examples of reasons to perform a TBA:
<br>
<br>
*The vehicle's battery has been disconnected and re-connected
*The ECU has been removed and reinstalled
*The Throttle Body has been cleaned or removed and reinstalled
*The Accelerator Pedal has been removed and reinstalled
<br>
In some vehicles, the car will not run correctly, or may not run at all without performing a TBA after one of the above operations. The TBA can be performed on both Drive-By-Wire (DBW or E-gas) as well as Cable-throttle cars as long as there is no Idle Stabilization Valve (ISV). If there is an ISV, then there is no motorized control of the throttle at all. Typically, '96-'99 VW/Audi have motorized Cable-throttle, and '00+ VW/Audi have DBW. Obviously, there are some exceptions. This should be obvious but TDI's do not have throttle bodies.
<br>
There are certain test conditions that must be met before doing a TBA:
*No DTC's in the Engine Controller
*Battery voltage at least 11.5 V
*Throttle must be at idling position (keep your foot off the gas pedal)
*Throttle body part must not be dirty (carbonized).
*Coolant temperature must be between 5 and 95C
<br>
== Cable-Throttle Engines == 
(These are engines with a physical cable between the accelerator and the throttle, but WITHOUT an ISV.)
<br>        
<br>
Turn the key on but do not start the car.
<br>
*'''[Select]'''
*'''[01 - Engine]'''
*'''[Measuring Blocks - 08]'''
Enter Group '''098''' (Note: Some SIMOS or Marelli ECU's use Group 001 such as  ADY & AEE engines)
*'''[Go!]'''
*'''[Switch to basic settings]'''
Once you do this you will see the top right display say ADP RUN. The TB adaptation is being done as soon as you switch to basic settings. You will see the values change and hear the TB cycle for the first few seconds then it will stop. Leave it in Basic Settings for about 30 seconds.
*Click the '''[Switch to Meas. Blocks]''' button and you're all set.
Be sure not to touch the accelerator and make sure the engine is NOT running when you do this!


== Drive-by-Wire (DBW) Engines using KW-1281 == 
(These are engines WITHOUT a physical cable between the accelerator and the throttle. Check to see if the engine speaks KW-1281 by looking in the top left of the Open Controller Screen Some examples of KWP-1281 engine controllers are 2000+ Golf/GTI/Jetta/New Beetle/Audi TT 1.8T)
<br>        
<br>
Turn the key on but do not start the car.
<br>
*'''[Select]'''
*'''[01 - Engine]'''
*'''[Measuring Blocks - 08]'''
Enter Group '''060'''
*'''[Go!]'''
*'''[Switch to basic settings]'''
Once you do this you will see the top right display say ADP RUN. The TB adaptation is being done as soon as you switch to basic settings. You will see the values change and hear the TB cycle for the first few seconds then it will stop. Leave it in Basic Settings for about 30 seconds.
*'''[Switch to Meas. Blocks]''' button and you're all set.
Be sure not to touch the accelerator and make sure the engine is NOT running when you do this!


== Drive-by-Wire (DBW) Engines using KWP-2089 == 
(These are engines WITHOUT a physical cable between the accelerator and the throttle. Check to see if the engine speaks KWP-2089 by looking in the top left of the Open Controller Screen Some examples of KWP-2089 engine controllers are the 2002+ Audi A4 and Passat)
<br>        
<br>
Turn the key on but do not start the car.
<br>
*'''[Select]'''
*'''[01 - Engine]'''
*'''[Basic Settings - 04]'''
*Group '''060'''
*'''[Go!]'''
It should say "Basic Settings: OFF" on the top of your screen.
*Click '''[ON/OFF/Next]''' to turn on Basic Settings.
It should now say "Basic Settings: ON" on the top of your screen. Once you do this you will see the top right display say ADP RUN. The TB adaptation is being done as soon as you switched basic settings on. You will see the values change and hear the TB cycle for the first few seconds then it will stop. Leave it in Basic Settings for about 30 seconds.
*Click ['''ON/OFF/Next]''' to turn off Basic Settings.
It should now say "Basic Settings: OFF" on the top of your screen
*Click the '''[Done, Go Back]''' button and you're all set.
Be sure not to touch the accelerator and make sure the engine is NOT running when you do this!