View source for Immobilizer III Key Matching (Cluster)

__FORCETOC__
'''This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with with Immobilizer III, where the immobilizer control module is integrated in the instrument cluster. See the seperate instructions for models where the [[Immobilizer III Key Matching (Box)|immobilizer control module is integrated in a separate immo box]] or where the [[Immobilizer III Immobilizer Swapping (Kessy)|immobilizer control module is integrated in kessy]] (Keyless Entry and Start SYstem).'''


== Determining IMMO-ID & VIN ==

'''[Select]'''<br>
'''[17 - Instruments]'''<br>
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.<br>
'''[Close Controller, Go Back - 06]'''<br>

---OR---

'''[Select]'''<br>
'''[17 - Instruments]'''<br>
'''[Meas. Blocks - 08]'''<br>
Select Block 081.<br>
'''[Go!]'''<br>
''The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.''.<br>
'''[Done, Go Back]'''<br>
'''[Close Controller, Go Back - 06]'''<br>


== Key Matching ==

'''<u>Prerequisites:</u>'''<br>
* All keys are either new or were adapted to this car (IMMO-ID) before.<br>
* You can match up to 8 keys.
* While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.''
* Battery voltage at least 12.5 V.<br>


'''[Select]'''<br>
'''[17 - Instruments]'''<br>
'''[Meas. Blocks - 08]'''<br>
Select Block 022.<br>
'''[Go!]'''<br>
''The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.''<br>
''You can check each key in this manner.''


Select Block 024.<br>
'''[Go!]'''<br>
''Make sure the shown lock times in field 1, 2 and 3 are '''0''' (each field represents a time in minutes).''<br>
* ''If the lock times are NOT '''0''':''
** ''Do NOT switch off the ignition!''
** ''Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-3.''
'''[Done, Go Back]'''<br>


'''[Login - 11]'''<br>
* '''4-digit PIN'''
** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
'''[Do it!]'''<br>


'''[Adaptation - 10]'''<br>
Enter 21 in "Channel Number".<br>
'''[Read]'''<br>
''The "Stored Value" is the number of keys currently matched.''<br>
Enter a "New value" of 0 "zero" to clear out any existing keys. <br>
'''[Test]'''<br>
Make sure "Test Value" shows 0 "zero"<br>
'''[Save]'''<br>
'''[Read]''' in Channel 21 again <br>
Enter a "New value" corresponding to the total number of keys to be matched,  including any existing keys.<br>
'''[Save]'''<br>
'''[Done, Go Back]'''<br>
'''[Close Controller, Go Back - 06]'''<br>

* ''Repeat the following steps until all keys have been matched:''<br>
**''Switch ignition off and remove key.''<br>
**''Insert next key to ignition and switch ignition on again.''<br>
**''The warning light for the Immobilizer will light up for ~2 seconds, then go out Switch ignition off and remove key.''<br>

'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''


== Video Link ==

Immobilizer Gen 2 and 3 Key Adaptation

[[File:Immobolizer.jpg|200px|link=http://www.youtube.com/watch?v=Wj3K04eMV7w]]

http://www.youtube.com/watch?v=Wj3K04eMV7w