View source for VW Golf (5K) AirbagVW10

__FORCETOC__

== Coding ==

AirbagVW10 modules are Index based Long Coded.  When using one of our professional grade HEX interfaces, the Airbag Coding Assistant should be used as explained on the following page of our [http://www.ross-tech.com/vcds/tour/recode_screen.html#Suggest interactive manual]. and our [[Airbag Coding]] tech tip.

== Adaptation ==

Used to deactivate individual airbag components (see repair manual for details).

== Basic Setting ==

=== Seat Occupied Recognition Control Module (J706) ===

If the Seat Occupied Recognition Control Module (J706) or the seat itself have been replaced, the basic setting has to be performed.

'''<u>Prerequisites:</u>'''<br>
* The vehicle is between 5° and 35°C (40° ~ 95°F).
* Battery voltage no less than 12.4 V.
* Passenger seat is empty and in normal position.
* Seatbelt must NOT be plugged in.
* No faults in the system.<br>

'''[Select]'''<br>
'''[15 - Airbags]'''<br>
'''[Security Access - 16]'''<br>
Enter the code shown in the  pop-up balloon to enable the basic setting.<br>
'''[Do it!]'''<br>
'''[Basic Settings - 04]'''<br>
'' When applicable type the single digit  0  into the (reserved ) box. If this is not present skip this step.''<br>
Select '''Seat occupied recognition serial number'''.<br>
'''[Go!]''' to activate the Basic Setting.<br>
After the result of '''Finished Correctly''' appears click '''[Stop]'''<br>

The Seat occupied recognition serial number reset has been performed.  Proceed directly to the [[VW Golf (5K) AirbagVW10#Seat Occupied Recognition Control Module (J706): Reset | Seat Occupied Recognition Control Module (J706): Reset]] procedure!<br>

=== Seat Occupied Recognition Control Module (J706): Reset ===

If a repair on the Seat Occupied Recognition has been performed, including the above basic settings procedure, a reset has to be performed too.

'''<u>Prerequisites:</u>'''<br>
* The vehicle is between 5° and 35°C (40° ~ 95°F).
* Battery voltage no less than 12.4 V.
* Passenger seat is empty and in normal position.
* Seatbelt must NOT be plugged in.
* No faults in the system.<br>


'''[Select]'''<br>
'''[15 - Airbags]'''<br>
'''[Security Access - 16]'''<br>
Enter the code shown in the  pop-up balloon to enable the basic setting.<br>
'''[Do it!]'''<br>
'''[Basic Settings - 04]'''<br>
'' When applicable type the single digit  0  into the (reserved ) box. If this is not present skip this step.''<br>
Select '''Resetting seat occupied recognition'''.<br>
'''[Go!]''' to activate the Basic Setting.<br>
After the result of '''Finished Correctly''' appears click '''[Stop]'''<br>
The reset has been performed.<br>
'''[Done, Go Back]'''<br>
'''[Fault Codes - 02]'''  ''Faults should NOT be stored''<br>
'''[Close Controller, Go Back - 06]'''<br>


== Special Notes ==
* If you click the basic settings tests out of sequence, you may need to exit the module, cycle the key and repeat the entire process.
* If the procedure results in an error message of any type or does not complete as expected:
# Registered users can send a complete Auto-Scan via  [mailto:Support@Ross-Tech.com email].
# Include specific details regarding which component(s) were replaced in the vehicle.
# Include specific details regarding the exact results when completing the basic settings procedure.<font color=white>E?ID=110711  and  ST?ID=34591</font><br>