View source for 6-Speed Direct Shift Gearbox (DSG/02E)

From Ross-Tech Wiki

← 6-Speed Direct Shift Gearbox (DSG/02E)

You do not have permission to edit this page, for the following reason:

---

You can view and copy the source of this page.

__FORCETOC__ '''General Information''' about this Transmission can be found in the [http://en.wikipedia.org/wiki/Direct-Shift_Gearbox Wikipedia entry]. Additional information can be found in the [[Official Factory Repair Information]] and sources such as [http://www.bentleypublishers.com//volkswagen/technical-training/vw-02e-direct-shift-gearbox-ssp.html Bentley Publisher's VW SSP (Self-Study Program 851403)] and [http://www.bentleypublishers.com//audi/technical-training/audi-02e-direct-shift-gearbox-ssp.html Bentley Publisher's Audi SSP (Self-Study Program 951403)].<br> <br> == Coding == * When replacing this Mechatronic unit, simply copy the coding from the original Auto-Scan and paste it into the New Coding section of the replacement followed by clicking '''[[http://www.ross-tech.com/vcds/tour/recode_screen.html Do it!]]'''. <br> * If the original Coding is unknown, coding information can be found in the pop-up balloon within the VCDS '''[[http://www.ross-tech.com/vcds/tour/recode_screen.html Coding-07]]''' function.<br> == Basic Setting == '''<u>Prerequisites:</u>'''<br> * Fluid Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019. (Fluid Level needs to be correct!) * Selector Lever in P * Ignition ON * Engine ON (Idling) for one minute or more * Brake Pedal operated (hold for the whole procedure) * Throttle Pedal not operated<br> '''''NOTE:''' Be sure to perform the following steps in the sequence shown, followed by the defined test drive.'' '''[Select]'''<br> '''[02 - Transmission]'''<br> '''[Basic Settings - 04]'''<br> === Transmission Tolerances (Engaged Calibration) === Group 061<br> '''[Go!]'''<br> * When you go to Basic Settings 061 and click GO the screen may look like this: [http://wiki.ross-tech.com/wiki/images/3/35/02-04-061_start.png Basic Settings 061]<br> * Wait until the numbers quit moving and the trans will quit making noises. Basic Settings switches to '''On''' when finished: [http://wiki.ross-tech.com/wiki/images/1/1e/02-04-061_end.png Basic Settings 061]<br> Wait until Basic Settings has switched to ON and all numbers have stopped moving. This may take one minute.<br> === Transmission Tolerances (Synch. Point. Measurement) === Group 060<br> '''[Go!]'''<br> * When you go to Basic Settings 060 and click GO the screen may look like this: [http://wiki.ross-tech.com/wiki/images/a/a8/02-04-060_start.png Basic Settings 060]<br> * Wait until the numbers quit moving and the trans will quit making noises. Basic Settings switches to '''On''' when finished: [http://wiki.ross-tech.com/wiki/images/3/3e/02-04-060_end.png Basic Settings 060]<br> Wait until Basic Settings has switched to ON and all numbers have stopped moving. === Clutch Adaptation === '''''Control Module Software Version < 0800:''''' Group 062<br> '''[Go!]'''<br> Activate the Basic Setting.<br> '''[ON/OFF/Next]'''<br> Special notes. *When found in the early software level (0627/0628) (8N) Audi TT: ** Basic Settings group 062 may take several minutes to complete. The final values may report: [18 | 18 | .285 | .24] and Basic Settings will report ON when finished. ** If Basic Settings group 062 reports ''ERROR:| Group 062| Not | Available'' try test driving the vehicle and repeating at normal operating temp. ''Internal Ref: ST?ID=66725 and E?ID=309867'' '''''Control Module Software Version >= 0800 :''''' Group 067<br> '''[Go!]'''<br> Activate the Basic Setting.<br> '''[ON/OFF/Next]'''<br> === Reset Values (Clutch Safety Function) === Group 068<br> '''[Go!]'''<br> Activate the Basic Setting.<br> '''[ON/OFF/Next]'''<br> === Reset Values (Pressure Adaptation) === Group 065<br> '''[Go!]'''<br> Activate the Basic Setting.<br> '''[ON/OFF/Next]'''<br> === Reset Values (Steering Wheel Paddle Installation) === Group 063<br> '''[Go!]'''<br> Activate the Basic Setting.<br> '''[ON/OFF/Next]'''<br> === Reset Values (ESP & Tip Cruise Control Installation) === Group 069<br> '''[Go!]'''<br> Activate the Basic Setting.<br> '''[ON/OFF/Next]'''<br> '''[Done, Go Back]'''<br> Switch off Ignition, wait 10 Seconds and switch it back on.<br> '''[Fault Codes - 02]'''<br> Check and clear fault codes after successful test.<br> '''[Close Controller, Go Back - 06]'''<br> Perform the Defined Test Drive.<br><br> == Special Procedures == === Defined Test Drive === ''Suggested test drive after replacing the mechatronic or successful basic setting.''<br><br> '''<u>Prerequisites:</u>'''<br> * Fluid Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019. * Do Not use Cruise Control. Drive in Tiptronic Mode from stand still up to 6th Gear.<br> While doing that make sure to drive in Gears 3 or 5 for approx. 5 minutes and also in 4 or 6 for approx. 5 minutes.<br> The engine speed window for all gears is 1200 - 3500 RPM (for clutch calibration).<br> Perform one sharp braking followed by a full throttle acceleration (oil return check) while in Drive, Not Tiptronic Mode.<br> Evaluate creep and starting-off points.<br> Check for leaks.<br> '''''NOTE:''' If the test drive cannot be performed in the recommended way or the necessary time, any remaining adaptations will be performed automatically during normal driving.'' ==== Special Notes ==== * Some modules do not require the use if the [ON/OFF/Next] button. If an Error is displayed after clicking the button, or the Basic Settings status does not switch to On, let the selected group and procedure finish on its own. * It is normal for the transmission to make noise while the tolerances are adapting. Do not exit or abort the Basic Settings sequence prematurely if you hear clacking noises. * Customers with TDI's have reported that an RPM range of 2000-2500 rpm is sufficient. ---- == Replacement == Replacement Mechatronic units should be ordered by VIN based on [[Production Codes (PR-Codes) can be found on the Vehicle Data Label | PR Codes]] to confirm vehicle compatibility. * Run and save a complete Auto-Scan and save it prior to Mechatronic unit removal. See the [http://www.ross-tech.com/vcds/tour/autoscan.html Online Manual Auto-Scan].<br> * Enter the original [[6-Speed Direct Shift Gearbox (DSG/02E)#Coding | Coding]] into the New Coding section of the replacement controller. * Complete [[6-Speed Direct Shift Gearbox (DSG/02E)#Basic Setting | Basic Settings]] * Complete the [[6-Speed Direct Shift Gearbox (DSG/02E)#Special Procedures | Defined Test Drive]] [[Category:Transmissions]]

Return to 6-Speed Direct Shift Gearbox (DSG/02E).