View source for Readiness - AXK Engine Code

=== Manually Generating Readiness ===



* <u>Ignition ON and Engine <b>OFF</b></u><br>



''Reading and clearing fault codes''<br>

'''[Select]'''<br>
'''[01 - Engine]'''<br>
'''[Fault Codes - 02]'''<br>
'''[Clear Codes -05]'''<br>
'''[Done, Go Back]'''<br>


''Throttle Body Alignment''<br>

'''[Measuring Blocks - 08]'''<br>
Select group 060<br>
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.<br>
'''[Switch to Meas. Blocks]'''<br>
'''[Done, Go Back]'''<br>
'''[Close Controller, Go Back]'''<br>



* <u>Ignition ON and Engine <b>ON</b> at idle</u><br>


''Fuel leakage test''<br>

'''[Select]'''<br>
'''[01 - Engine]'''<br>
'''[Measuring Blocks - 08]'''<br>
Select group 202<br>
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
Leave it in Basic Settings until the fourth field reads xxxxx100<br>
'''[Switch to Meas. Blocks]'''<br>


''Evap purge test''<br>

Select group 070<br>
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
Leave it in Basic Settings until the fourth field reads EVAP OK<br>
'''[Switch to Meas. Blocks]'''<br>


''A/F control test''<br>

Select group 107<br>
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
Leave it in Basic Settings until the fourth field reads Syst.OK<br>
'''[Switch to Meas. Blocks]'''<br>



* <u>Ignition ON and Engine <b>ON between 1800 and 2200 rpm</b></u><br>



''O2 sensor heater test''<br>

Select group 041<br>
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
Leave it in Basic Settings until there are kOhm readings in the first and third fields<br>
'''[Switch to Meas. Blocks]'''<br>
Select group 042<br>
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
Leave it in Basic Settings until there are kOhm readings in the first and third fields<br>
'''[Switch to Meas. Blocks]'''<br>



* <u>Ignition ON and Engine <b>ON at idle</b></u><br>



''Post-cat O2 sensors readiness test''<br>

Select group 036<br>
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
Leave it in Basic Settings until you see B1-S2 OK in the first field and B2-S2 OK in the third field<br>
'''[Switch to Meas. Blocks]'''<br>



* <u>Ignition ON and Engine <b>ON between 1520 and 2280 rpm</b></u><br>



''Pre-cat O2 sensors response time test''<br>

Select group 034<br>
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
Leave it in Basic Settings until the fourth field reads B1-S1 OK<br>
'''[Switch to Meas. Blocks]'''<br>
Select group 035<br>
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
Leave it in Basic Settings until the fourth field reads B2-S1 OK<br>
'''[Switch to Meas. Blocks]'''<br>



* <u>Ignition ON and Engine <b>ON at idle</b></u><br>



''O2 sensor control test''<br>

Select group 037<br>
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
Leave it in Basic Settings until the fourth field reads Syst. OK<br>
'''[Switch to Meas. Blocks]'''<br>
Select group 038<br>
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
Leave it in Basic Settings until the fourth field reads Syst. OK<br>
'''[Switch to Meas. Blocks]'''<br>



''Post-cat O2 sensor aging test''<br>

Select group 043<br>
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
Leave it in Basic Settings until the fourth field reads B1-S2 OK<br>
'''[Switch to Meas. Blocks]'''<br>
Select group 044<br>
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
Leave it in Basic Settings until the fourth field reads B2-S2 OK<br>
'''[Switch to Meas. Blocks]'''<br>



* <u>Ignition ON and Engine <b>ON between 1880 and 2280 rpm</b></u><br>



''Catalytic converter test''<br>

Select group 046<br>
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
Leave it in Basic Settings until the fourth field reads CAT B1 OK<br>
'''[Switch to Meas. Blocks]'''<br>
Select group 047<br>
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
Leave it in Basic Settings until the fourth field reads CAT B2 OK<br>
'''[Switch to Meas. Blocks]'''<br>



* <u>Ignition ON and Engine <b>ON at idle</b></u><br>



''Secondary air injection test (applies to Auto Trans vehicles only!)''<br>

Select group 077<br>
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
Leave it in Basic Settings until the fourth field reads Syst. OK<br>
'''[Switch to Meas. Blocks]'''<br>
Select group 078<br>
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
Leave it in Basic Settings until the fourth field reads Syst. OK<br>
'''[Switch to Meas. Blocks]'''<br>
'''[Done, Go Back]'''<br>


''Checking Readiness''<br>
'''[Readiness]'''<br>
Make sure none of the fields say Failed or Incomplete<br>
'''[Done, Go Back]'''<br>
'''[Close Controller, Go Back]'''<br>



<i>You're done! </i><br>