6-Speed Automatic Transmission (01J/Multitronic) - Revision history

Peter: /* Special Notes */

2016-04-28T20:32:10Z

Special Notes

← Older revision		Revision as of 20:32, 28 April 2016
Line 54:		Line 54:
	==== Special Notes ====		==== Special Notes ====
	* The CVT TCM must be ordered by VIN due to the specific programming related to the engine configuration, market/country configuration and 6 or 7 plate clutch system. The [http://www.ross-tech.com/vcds/tour/open_screen.html Component field] will display some of the mentioned information when scanning it with VCDS. Installing the incorrect TCM will have undesirable results.		* The CVT TCM must be ordered by VIN due to the specific programming related to the engine configuration, market/country configuration and 6 or 7 plate clutch system. The [http://www.ross-tech.com/vcds/tour/open_screen.html Component field] will display some of the mentioned information when scanning it with VCDS. Installing the incorrect TCM will have undesirable results.
	* If the Adaptation values are not stored to the TCM in the NAR (North American Region) Audi A4, A4 Cabrio and A6 models ranging from 2002 through 2008 see TSB: 37-08-20 (2015849/2). This TSB explains some of the conditions that may cause an unsuccessful adaptation drive.		* If the Adaptation values are not stored to the TCM in the NAR (North American Region) Audi A4, A4 Cabrio and A6 models ranging from 2002 through 2008 see TSB: 37-08-20 (2015849). This TSB explains some of the conditions that may cause an unsuccessful adaptation drive.

	[[Category:Transmissions]]		[[Category:Transmissions]]

Dana at 15:06, 12 September 2012

2012-09-12T15:06:41Z

← Older revision		Revision as of 15:06, 12 September 2012
Line 53:		Line 53:

	==== Special Notes ====		==== Special Notes ====
			* The CVT TCM must be ordered by VIN due to the specific programming related to the engine configuration, market/country configuration and 6 or 7 plate clutch system. The [http://www.ross-tech.com/vcds/tour/open_screen.html Component field] will display some of the mentioned information when scanning it with VCDS. Installing the incorrect TCM will have undesirable results.
	* If the Adaptation values are not stored to the TCM in the NAR (North American Region) Audi A4, A4 Cabrio and A6 models ranging from 2002 through 2008 see TSB: 37-08-20 (2015849/2). This TSB explains some of the conditions that may cause an unsuccessful adaptation drive.		* If the Adaptation values are not stored to the TCM in the NAR (North American Region) Audi A4, A4 Cabrio and A6 models ranging from 2002 through 2008 see TSB: 37-08-20 (2015849/2). This TSB explains some of the conditions that may cause an unsuccessful adaptation drive.

	[[Category:Transmissions]]		[[Category:Transmissions]]

Dana at 14:59, 12 September 2012

2012-09-12T14:59:36Z

← Older revision		Revision as of 14:59, 12 September 2012
Line 42:		Line 42:
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Close Controller, Go Back - 06]'''<br><br>		'''[Close Controller, Go Back - 06]'''<br><br>

			== Replacement ==
			* Run and save a complete Auto-Scan and save it prior to module removal. See the [http://www.ross-tech.com/vcds/tour/autoscan.html Online Manual Auto-Scan].<br>
			* Code the module with the Coding from the original module found in the Auto-Scan.<br>
			* Complete the Adaptation as shown above followed by the Defined Test Drive.<br>


			'''Note''': The (4F) chassis Audi A6 uses '''Component Protection''' and will result in the [[18109/P1701 \| 18109/P1701- Transmission Control Unit: Locked]] fault after module replacement. The transmission will have limited functions prior to the dealer SVM process required for unlocking Component Protection

Peter at 19:06, 20 August 2012

2012-08-20T19:06:15Z

← Older revision		Revision as of 19:06, 20 August 2012
Line 26:		Line 26:
	'''[02 - Transmission]'''<br>		'''[02 - Transmission]'''<br>
	'''[Adaptation - 10]'''<br>		'''[Adaptation - 10]'''<br>
	Channel ~~000~~<br>		Channel 00<br>
	'''[Read]'''<br>		'''[Read]'''<br>
	'''[Save]'''<br>		'''[Save]'''<br>

Dana at 15:29, 5 May 2011

2011-05-05T15:29:43Z

← Older revision		Revision as of 15:29, 5 May 2011
Line 1:		Line 1:
	__FORCETOC__		__FORCETOC__
	== Coding ==		== Coding ==
	To Code this transmission, make sure Ignition is ON, but Engine is NOT running.		To Code this transmission, make sure Ignition is ON, but Engine is NOT running.<br>
			When replacing this module use the coding from the original unit or the repair manual coding charts.<br>

	== Adaptation ==		== Adaptation ==

Dana at 15:31, 21 January 2011

2011-01-21T15:31:29Z

← Older revision		Revision as of 15:31, 21 January 2011
Line 41:		Line 41:
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Close Controller, Go Back - 06]'''<br><br>		'''[Close Controller, Go Back - 06]'''<br><br>


			==== Special Notes ====

			* If the Adaptation values are not stored to the TCM in the NAR (North American Region) Audi A4, A4 Cabrio and A6 models ranging from 2002 through 2008 see TSB: 37-08-20 (2015849/2). This TSB explains some of the conditions that may cause an unsuccessful adaptation drive.

	[[Category:Transmissions]]		[[Category:Transmissions]]

Uwe: /* Coding */

2007-12-04T19:26:06Z

Coding

← Older revision		Revision as of 19:26, 4 December 2007
Line 1:		Line 1:
	__FORCETOC__		__FORCETOC__
	== Coding ==		== Coding ==
			To Code this transmission, make sure Ignition is ON, but Engine is NOT running.

	== Adaptation ==		== Adaptation ==
	== Special Procedures ==		== Special Procedures ==

RtWiKiSyS0p at 10:39, 3 August 2006

2006-08-03T10:39:00Z

← Older revision		Revision as of 10:39, 3 August 2006
Line 11:		Line 11:
	* Transmission Oil Temperature must be between 60 °C and 90 °C.		* Transmission Oil Temperature must be between 60 °C and 90 °C.
	** If the procedure does not succeed in the first try, make sure the temperature is above 80 °C.		** If the procedure does not succeed in the first try, make sure the temperature is above 80 °C.
			* All driving and braking has to be done in partial load, avoid full throttle/braking!
	* Normally the adaptation needs to be carried out when:		* Normally the adaptation needs to be carried out when:
	** Transmission Control Module has been recoded		** Transmission Control Module has been recoded

RtWiKiSyS0p at 00:48, 3 August 2006

2006-08-03T00:48:42Z

← Older revision		Revision as of 00:48, 3 August 2006
Line 11:		Line 11:
	* Transmission Oil Temperature must be between 60 °C and 90 °C.		* Transmission Oil Temperature must be between 60 °C and 90 °C.
	** If the procedure does not succeed in the first try, make sure the temperature is above 80 °C.		** If the procedure does not succeed in the first try, make sure the temperature is above 80 °C.
			* Normally the adaptation needs to be carried out when:
			** Transmission Control Module has been recoded
			** Input Shaft has been replaced
			** Hydraulic Unit has been replaced
			** Transmission Control Module has been replaced
			** Transmission has been replaced


	'''[Select]'''<br>		'''[Select]'''<br>

RtWiKiSyS0p at 00:43, 3 August 2006

2006-08-03T00:43:23Z

New page

__FORCETOC__
== Coding ==
== Adaptation ==
== Special Procedures ==

=== Defined Test Drive ===

'''Prerequisites:'''
* Ignition ON and Engine ON.
* No Fault Codes stored.
* Transmission Oil Temperature must be between 60 °C and 90 °C.
** If the procedure does not succeed in the first try, make sure the temperature is above 80 °C.

'''[Select]''' 
'''[02 - Transmission]''' 
'''[Adaptation - 10]''' 
Channel 000 
'''[Read]''' 
'''[Save]''' 
'''[Done, Go Back]''' 
'''[Measuring Blocks - 08]''' 
Block 010 (in 1st Row) 
Block 011 (in 2nd Row) 
'''[Go!]''' 
Check fields 2, specification is '''ADP OK'''. 
* Move the selector lever in position '''D''' and drive with partial load '''20 m / 70 ft''' forward, then brake to standstill.
* Hold the brake for 10 seconds.
* Move the selector lever in position '''R''' and drive with partial load '''20 m / 70 ft''' reverse, then brake to standstill.
* Hold the brake for 10 seconds.
The procedure needs to be repeated at least 5 times and can be repeated up to 10 times until the measuring values show '''ADP OK'''. 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]''' 

[[Category:Transmissions]]