Audi A4 (8R/8K) Parking Brake EPB-4 - Revision history

Andy: /* Open Rear Parking Brake */

2017-02-10T17:25:58Z

Open Rear Parking Brake

← Older revision		Revision as of 17:25, 10 February 2017
Line 22:		Line 22:

	''The caliper pistons do not move back into the caliper, they must be pushed in using a hand tool.''<br>		''The caliper pistons do not move back into the caliper, they must be pushed in using a hand tool.''<br>
			''It is normal for the parking brake light to flash, indicating that the brake cannot be used while the calipers are in this service mode.''<br>
	'' Do not operate the EPB switch or continue with the Close Rear Parking Brake step until the rear brakes are reassembled!		'' Do not operate the EPB switch or continue with the Close Rear Parking Brake step until the rear brakes are reassembled!

Jef: /* Close Rear Parking Brake */

2016-01-12T19:49:34Z

Close Rear Parking Brake

← Older revision		Revision as of 19:49, 12 January 2016
Line 38:		Line 38:
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>
	Cycle the Parking Brake ON and back OFF again using the switch in the vehicle while holding the brake pedal. Check for fault code(s) before the test drive.		Cycle the Parking Brake ON and back OFF again using the switch in the vehicle while holding the brake pedal. Check for fault code(s) before the test drive.

			== Video Link ==
			=== Electro-Mechanical Parking Brake (EPB): Rear Brake Service ===

			[[File:Image4.jpg\|200px\|link=https://www.youtube.com/watch?v=zFZJj39FZ3s]]

			https://www.youtube.com/watch?v=zFZJj39FZ3s

Dana at 15:42, 13 March 2015

2015-03-13T15:42:45Z

← Older revision		Revision as of 15:42, 13 March 2015
Line 34:		Line 34:
	'''[Go!]''' to activate the Basic Setting.<br>		'''[Go!]''' to activate the Basic Setting.<br>
	The brake calipers will then close.<br>		The brake calipers will then close.<br>
	After the result of '''~~Finished Correctly~~''' appears click '''[Stop]'''<br>		After the result of '''Not Running''' (or Finished Correctly) appears click '''[Stop]'''<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>
	Cycle the Parking Brake ON and back OFF again using the switch in the vehicle while holding the brake pedal. Check for fault code(s) before the test drive.		Cycle the Parking Brake ON and back OFF again using the switch in the vehicle while holding the brake pedal. Check for fault code(s) before the test drive.

Dana at 22:31, 17 February 2015

2015-02-17T22:31:55Z

← Older revision		Revision as of 22:31, 17 February 2015
Line 1:		Line 1:
	~~Users can refer~~ to the ~~UDS Protocol~~ [[~~Audi A6 (4G~~/~~4H)~~ Parking Brake]] while ~~this page is under construction~~.		== Basic Setting ==
			=== Caution! ===
			* Do not perform any of these Basic Settings while the brakes are disassembled! Opening, closing, function tests, and otherwise cycling the Electronic Parking brakes should only be done with the pads and calipers properly installed on the rotors.
			* Please follow the procedures EXACTLY. There's a reason for every step. If you skip any prerequisites or other steps here, you are likely to experience "issues" for which no documented resolutions exist, in which case we will not be able to help you resolve them.
			* It is strongly recommended to run a full Auto-Scan to check for any preexisting faults!

			=== Open Rear Parking Brake ===
			'''<u>Prerequisites:</u>'''<br>
			* ALL rear brake components are assembled.
			* Connect a battery charger as per repair manual.
			* Cycle the Parking Brake ON, then OFF first.
			'''[Select]'''<br>
			'''[53 - Parking Brake]'''<br>
			'''[Basic Settings - 04]'''<br>
			Select '''Start lining change mode'''''<br>
			'''[Go!]''' to activate the Basic Setting.<br>
			The brake calipers will then open, allowing the pads to be changed.<br>
			After the result of '''Finished Correctly''' appears click '''[Stop]'''<br>
			'''[Done, Go Back]'''<br>
			'''[Close Controller, Go Back - 06]'''
			* Turn ignition off and leave battery charger connected.<br>

			''The caliper pistons do not move back into the caliper, they must be pushed in using a hand tool.''<br>
			'' Do not operate the EPB switch or continue with the Close Rear Parking Brake step until the rear brakes are reassembled!

			=== Close Rear Parking Brake ===
			'''<u>Prerequisites:</u>'''<br>
			* ALL rear brake components reassembled.
			* Connect a battery charger as per repair manual.
			'''[Select]'''<br>
			'''[53 - Parking Brake]'''<br>
			'''[Basic Settings - 04]'''<br>
			Select '''End lining change mode'''''<br>
			'''[Go!]''' to activate the Basic Setting.<br>
			The brake calipers will then close.<br>
			After the result of '''Finished Correctly''' appears click '''[Stop]'''<br>
			'''[Done, Go Back]'''<br>
			'''[Close Controller, Go Back - 06]'''<br>
			Cycle the Parking Brake ON and back OFF again using the switch in the vehicle while holding the brake pedal. Check for fault code(s) before the test drive.

Dana: Created page with "Users can refer to the UDS Protocol Audi A6 (4G/4H) Parking Brake while this page is under construction."

2015-01-16T17:06:14Z

Created page with "Users can refer to the UDS Protocol Audi A6 (4G/4H) Parking Brake while this page is under construction."

New page

Users can refer to the UDS Protocol [[Audi A6 (4G/4H) Parking Brake]] while this page is under construction.