Audi Q7 (4L) Brake Electronics - Revision history

Dana at 03:58, 19 February 2012

2012-02-19T03:58:57Z

@@ Line 30: / Line 30: @@
 After a successful basic setting, field 2 should say "OK".<br>
 '''[Done, Go Back]'''<br>
-To make sure the basic setting was succesful, check the sensor again.<br>
+To make sure the basic setting was successful, check the sensor again.<br>
 '''[Measuring Blocks - 08]'''<br>
 Group 004<br>
@@ Line 37: / Line 37: @@
 '''[Done, Go Back]'''<br>
 '''[Close Controller, Go Back - 06]'''<br>

RtWiKiSyS0p at 22:34, 31 August 2010

2010-08-31T22:34:35Z

← Older revision		Revision as of 22:34, 31 August 2010
Line 1:		Line 1:
			== Coding ==

			'''If the old Control Module is still accessible read/copy it's Coding to the new Module. In case this is not possible please [http://www.ross-tech.com/contact.html contact us directly] and we will assist you with the Coding Process.

			''Every inquiry on this topic has to include a full Auto-Scan as well as which parts have been replaced and why, also make sure the Auto-Scan includes the complete VIN of the vehicle in question.''<br> <br> <br>


	== Basic Setting ==		== Basic Setting ==

	=== Sensor for Steering Angle (G85) ===		=== Sensor for Steering Angle (G85) ===

Dana: Created page with '== Basic Setting == === Sensor for Steering Angle (G85) === '''Prerequisites:'''
* Start the vehicle. * Turn the steering wheel one turn to the right and one turn to…'

2010-08-31T20:09:19Z

Created page with '== Basic Setting == === Sensor for Steering Angle (G85) === '''Prerequisites:''' * Start the vehicle. * Turn the steering wheel one turn to the right and one turn to…'

New page

== Basic Setting ==

=== Sensor for Steering Angle (G85) ===

'''Prerequisites:''' 
* Start the vehicle.
* Turn the steering wheel one turn to the right and one turn to the left.
* Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.
* If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight.
* Ensure that the steering wheel is not moved again.
* Keep the engine running and do not switch off the ignition.
* System voltage at least 12.0 V

'''[Select]''' 
'''[03 - Brake Electronics]''' 
'''[Security Access - 16]''' 
Enter 40168, to enable the basic setting. 
'''[Do it!]''' 
'''[Basic Settings - 04]''' 
Group 060 
'''[Go!]''' 
Activate the Basic Setting. 
'''[ON/OFF/Next]''' 
After a successful basic setting, field 2 should say "OK". 
'''[Done, Go Back]''' 
To make sure the basic setting was succesful, check the sensor again. 
'''[Measuring Blocks - 08]''' 
Group 004 
'''[Go!]''' 
Check field 1, the value has to be between -1.5 and +1.5 °. 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]'''

Audi Q7 (4L) Brake Electronics - Revision history

Dana at 03:58, 19 February 2012

RtWiKiSyS0p at 22:34, 31 August 2010

Dana: Created page with '== Basic Setting == === Sensor for Steering Angle (G85) === '''Prerequisites:''' * Start the vehicle. * Turn the steering wheel one turn to the right and one turn to…'

Dana: Created page with '== Basic Setting == === Sensor for Steering Angle (G85) === '''Prerequisites:'''
* Start the vehicle. * Turn the steering wheel one turn to the right and one turn to…'