Peter: /* Longitudinal Acceleration Sensor (G251) */

2015-05-18T13:48:51Z

Longitudinal Acceleration Sensor (G251)

← Older revision		Revision as of 13:48, 18 May 2015
Line 99:		Line 99:

	'''<u>Prerequisites:</u>'''<br>		'''<u>Prerequisites:</u>'''<br>
	* System voltage at least 12.0 V.<br><br>		* System voltage at least 12.0 V.<br>
			* Measuring Value Block Group 006, Field 1 is between (-1.5) and (+1.5) m/s²<br><br>

	'''[Select]'''<br>		'''[Select]'''<br>
Line 113:		Line 114:
	After a successful basic setting, field 2 should say "OK".<br>		After a successful basic setting, field 2 should say "OK".<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	To make sure the basic setting was ~~succesful~~, check the sensor again.<br>		To make sure the basic setting was successful, check the sensor again.<br>
	'''[Measuring Blocks - 08]'''<br>		'''[Measuring Blocks - 08]'''<br>
	Group 006<br>		Group 006<br>
	'''[Go!]'''<br>		'''[Go!]'''<br>
	Check field 1, the value has to be between -1.5 and +1.5 m/s².<br>		Re-Check field 1, the value has to be between -1.5 and +1.5 m/s².<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>


	== Special Procedures ==		== Special Procedures ==

RtWiKiSyS0p: New page: FORCETOC == Coding == === ABS/EDS/ASR/ESP (Front-Wheel-Drive) === === ABS/EDS/ASR/ESP (All-Wheel-Drive) === == Basic Setting == === Sensor for Steering Angle (G85) === '''Prereq...

2007-10-26T13:39:32Z

New page: __FORCETOC__ == Coding == === ABS/EDS/ASR/ESP (Front-Wheel-Drive) === === ABS/EDS/ASR/ESP (All-Wheel-Drive) === == Basic Setting == === Sensor for Steering Angle (G85) === '''Prereq...

New page

__FORCETOC__

== Coding ==
=== ABS/EDS/ASR/ESP (Front-Wheel-Drive) ===
=== ABS/EDS/ASR/ESP (All-Wheel-Drive) ===

== Basic Setting ==
=== Sensor for Steering Angle (G85) ===

'''Prerequisites:''' 
* Start the vehicle.
* Turn the steering wheel one turn to the right and one turn to the left.
* Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.
* If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight.
* Ensure that the steering wheel is not moved again.
* Keep the engine running and do not switch off the ignition.
* System voltage at least 12.0 V. 

'''[Select]''' 
'''[03 - Brake Electronics]''' 
'''[Coding-II - 11]''' 
Enter 40168, to enable the basic setting. 
'''[Do it!]''' 
'''[Basic Settings - 04]''' 
Group 060 
'''[Go!]''' 
Activate the Basic Setting. 
'''[ON/OFF/Next]''' 
After a successful basic setting, field 2 should say "OK". 
'''[Done, Go Back]''' 
To make sure the basic setting was succesful, check the sensor again. 
'''[Measuring Blocks - 08]''' 
Group 004 
'''[Go!]''' 
Check field 1, the value has to be between -4.5 and +4.5 °. 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]''' 

=== Lateral Acceleration Sensor (G200) ===

'''Prerequisites:''' 
* System voltage at least 12.0 V. 

'''[Select]''' 
'''[03 - Brake Electronics]''' 
'''[Measuring Blocks - 08]''' 
Group 004 
'''[Go!]''' 
Check field 2, the value has to be between -1.5 and +1.5 m/s². 
'''[Done, Go Back]''' 
'''[Coding-II - 11]''' 
Enter 40168, to enable the basic setting. 
'''[Do it!]''' 
'''[Basic Settings - 04]''' 
Group 063 
'''[Go!]''' 
Activate the Basic Setting. 
'''[ON/OFF/Next]''' 
After a successful basic setting, field 2 should say "OK". 
'''[Done, Go Back]''' 
To make sure the basic setting was succesful, check the sensor again. 
'''[Measuring Blocks - 08]''' 
Group 004 
'''[Go!]''' 
Check field 2, the value has to be between -1.5 and +1.5 m/s². 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]''' 

=== Brake Pressure Sensor 1 (G201) ===

'''Prerequisites:''' 
* System voltage at least 12.0 V. 

'''[Select]''' 
'''[03 - Brake Electronics]''' 
'''[Coding-II - 11]''' 
Enter 40168, to enable the basic setting. 
'''[Do it!]''' 
'''[Basic Settings - 04]''' 
Group 066 
'''[Go!]''' 
Activate the Basic Setting. 
'''[ON/OFF/Next]''' 
After a successful basic setting, field 2 should say "OK". 
'''[Done, Go Back]''' 
To make sure the basic setting was succesful, check the sensor again. 
'''[Measuring Blocks - 08]''' 
Group 005 
'''[Go!]''' 
Check field 1, the value has to be between -7.0 and +7.0 bar. 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]''' 

=== Longitudinal Acceleration Sensor (G251) ===

'''Prerequisites:''' 
* System voltage at least 12.0 V. 

'''[Select]''' 
'''[03 - Brake Electronics]''' 
'''[Coding-II - 11]''' 
Enter 40168, to enable the basic setting. 
'''[Do it!]''' 
'''[Basic Settings - 04]''' 
Group 069 
'''[Go!]''' 
Activate the Basic Setting. 
'''[ON/OFF/Next]''' 
After a successful basic setting, field 2 should say "OK". 
'''[Done, Go Back]''' 
To make sure the basic setting was succesful, check the sensor again. 
'''[Measuring Blocks - 08]''' 
Group 006 
'''[Go!]''' 
Check field 1, the value has to be between -1.5 and +1.5 m/s². 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]''' 

== Special Procedures ==

=== System Function Test ===

See [[ESP System Function Test (Conti/Teves)|System Function Test]]

Audi TT (8N) Brake Electronics (MK60) - Revision history

Peter: /* Longitudinal Acceleration Sensor (G251) */

RtWiKiSyS0p: New page: __FORCETOC__ == Coding == === ABS/EDS/ASR/ESP (Front-Wheel-Drive) === === ABS/EDS/ASR/ESP (All-Wheel-Drive) === == Basic Setting == === Sensor for Steering Angle (G85) === '''Prereq...

RtWiKiSyS0p: New page: FORCETOC == Coding == === ABS/EDS/ASR/ESP (Front-Wheel-Drive) === === ABS/EDS/ASR/ESP (All-Wheel-Drive) === == Basic Setting == === Sensor for Steering Angle (G85) === '''Prereq...