Immobilizer III Immobilizer Swapping (Kessy) - Revision history

Andy at 15:01, 24 July 2013

2013-07-24T15:01:02Z

← Older revision		Revision as of 15:01, 24 July 2013
Line 1:		Line 1:
	__FORCETOC__		__FORCETOC__
	'''This procedure details how to change the ~~instrument cluster~~ on VW/Audi/Seat/Skoda vehicles with Immobilizer III, where the immobilizer control module is integrated with KESSY (<u>K</u>eyless <u>E</u>ntry and <u>S</u>tart <u>Sy</u>stem). See the separate instructions for models where the [[Immobilizer III Immobilizer Swapping (Separate)\|immobilizer control module is integrated in a separate control module]] or where the [[Immobilizer III Immobilizer Swapping (Instrument Cluster)\|immobilizer control module is integrated in Instrument Cluster]].'''		'''This procedure details how to change the immobilizer control module on VW/Audi/Seat/Skoda vehicles with Immobilizer III, where the immobilizer control module is integrated with KESSY (<u>K</u>eyless <u>E</u>ntry and <u>S</u>tart <u>Sy</u>stem). See the separate instructions for models where the [[Immobilizer III Immobilizer Swapping (Separate)\|immobilizer control module is integrated in a separate control module]] or where the [[Immobilizer III Immobilizer Swapping (Instrument Cluster)\|immobilizer control module is integrated in Instrument Cluster]].'''

Jef: /* Kessy Control Module Swapping */

2012-07-12T22:15:54Z

Kessy Control Module Swapping

← Older revision		Revision as of 22:15, 12 July 2012
Line 56:		Line 56:
	'''[Sec. Access - 16]'''<br>		'''[Sec. Access - 16]'''<br>
	''For the following procedure, '''use the PIN of the NEW (USED)''' control module.''<br>		''For the following procedure, '''use the PIN of the NEW (USED)''' control module.''<br>
	~~''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''<br>~~
	* '''4-digit PIN'''		* '''4-digit PIN'''
	** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''		** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
	* '''7-digit PIN'''
	** '''[Use 7-digit PIN/SKC]'''
	** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
	** '''[OK]'''
	** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
	'''[Do it!]'''<br>		'''[Do it!]'''<br>

Line 71:		Line 65:
	'''[Read]'''<br>		'''[Read]'''<br>
	''For the following procedure, '''use the PIN of the OLD (ORIGINAL)''' control module.''<br>		''For the following procedure, '''use the PIN of the OLD (ORIGINAL)''' control module.''<br>
	~~''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''<br>~~
	* '''4-digit PIN'''		* '''4-digit PIN'''
	** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''		** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
	* '''7-digit PIN'''
	** '''[Use 7-digit PIN/SKC]'''
	** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
	** '''[OK]'''
	** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
	'''[Test]'''<br>		'''[Test]'''<br>
	'''[Save]'''<br>		'''[Save]'''<br>

Florian at 10:22, 15 June 2011

2011-06-15T10:22:00Z

← Older revision		Revision as of 10:22, 15 June 2011
Line 1:		Line 1:
	__FORCETOC__		__FORCETOC__
	'''This procedure details how to change the instrument cluster on VW/Audi/Seat/Skoda vehicles with Immobilizer III, where the immobilizer control module is integrated ~~in instrument cluster~~. See the separate instructions for models where the [[Immobilizer III Immobilizer Swapping (Separate)\|immobilizer control module is integrated in a separate control module]] or where the [[Immobilizer III Immobilizer Swapping (Instrument Cluster)\|immobilizer control module is integrated in Instrument Cluster]].'''		'''This procedure details how to change the instrument cluster on VW/Audi/Seat/Skoda vehicles with Immobilizer III, where the immobilizer control module is integrated with KESSY (<u>K</u>eyless <u>E</u>ntry and <u>S</u>tart <u>Sy</u>stem). See the separate instructions for models where the [[Immobilizer III Immobilizer Swapping (Separate)\|immobilizer control module is integrated in a separate control module]] or where the [[Immobilizer III Immobilizer Swapping (Instrument Cluster)\|immobilizer control module is integrated in Instrument Cluster]].'''


Line 83:		Line 83:
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>

	After a successful adaptation a lock time will automatically ~~being~~ set.<br>		After a successful adaptation a lock time will automatically be set.<br>
	'''[Meas. Blocks - 08]'''<br>		'''[Meas. Blocks - 08]'''<br>
	Select Block 024.<br>		Select Block 024.<br>
	'''[Go!]'''<br>		'''[Go!]'''<br>
	''Make sure the shown lock ~~times~~ in field 4 is '''0''' (a field represents a time in minutes).''<br>		''Make sure the shown lock time in field 4 is '''0''' (a field represents a time in minutes).''<br>
	* ''If the lock time is NOT '''0''':''		* ''If the lock time is NOT '''0''':''
	** ''Do NOT switch off the ignition!''		** ''Do NOT switch off the ignition!''

RtWiKiSyS0p at 16:32, 23 January 2009

2009-01-23T16:32:51Z

← Older revision		Revision as of 16:32, 23 January 2009
Line 79:		Line 79:
	** '''[OK]'''		** '''[OK]'''
	** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".		** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
			'''[Test]'''<br>
	'''[Save]'''<br>		'''[Save]'''<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>

RtWiKiSyS0p at 15:59, 19 July 2007

2007-07-19T15:59:22Z

← Older revision		Revision as of 15:59, 19 July 2007
Line 35:		Line 35:
	* Battery voltage at least 12.0 V. We strongly recommend the use of a battery charger.		* Battery voltage at least 12.0 V. We strongly recommend the use of a battery charger.
	* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) control module.		* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) control module.


	* Put the first Key into the ignition Lock, but do NOT switch ON the ignition.		* Put the first Key into the ignition Lock, but do NOT switch ON the ignition.

RtWiKiSyS0p at 15:41, 19 July 2007

2007-07-19T15:41:53Z

← Older revision		Revision as of 15:41, 19 July 2007
Line 4:		Line 4:

	== Determining IMMO-ID & VIN (ECU) ==		== Determining IMMO-ID & VIN (ECU) ==

	~~'''[Select]'''<br>~~
	~~'''[01 - Engine]'''<br>~~
	~~Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.<br>~~
	~~'''[Close Controller, Go Back - 06]'''<br>~~

	~~---OR---~~

	'''[Select]'''<br>		'''[Select]'''<br>
Line 23:		Line 16:

	== Determining IMMO-ID & VIN (Kessy) ==		== Determining IMMO-ID & VIN (Kessy) ==

	~~'''[Select]'''<br>~~
	~~'''[05 - Acc/Start Auth.]'''<br>~~
	~~Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.<br>~~
	~~'''[Close Controller, Go Back - 06]'''<br>~~

	~~---OR---~~

	'''[Select]'''<br>		'''[Select]'''<br>
Line 47:		Line 33:
	* ORIGINAL Electric Steering Lock is still installed.		* ORIGINAL Electric Steering Lock is still installed.
	** If the ORIGINAL Electric Steering Lock has been replaced, perform [[Immobilizer III Electric Steering Lock Adaptation (Kessy)\|Electric Steering Lock Adaptation]] first.		** If the ORIGINAL Electric Steering Lock has been replaced, perform [[Immobilizer III Electric Steering Lock Adaptation (Kessy)\|Electric Steering Lock Adaptation]] first.
	* Battery voltage at least 12.0 V.		* Battery voltage at least 12.0 V. We strongly recommend the use of a battery charger.
	* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) control module.		* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) control module.

RtWiKiSyS0p at 14:14, 19 July 2007

2007-07-19T14:14:04Z

← Older revision		Revision as of 14:14, 19 July 2007
Line 46:		Line 46:
	* The NEW module is installed in the car.		* The NEW module is installed in the car.
	* ORIGINAL Electric Steering Lock is still installed.		* ORIGINAL Electric Steering Lock is still installed.
			** If the ORIGINAL Electric Steering Lock has been replaced, perform [[Immobilizer III Electric Steering Lock Adaptation (Kessy)\|Electric Steering Lock Adaptation]] first.
	* Battery voltage at least 12.0 V.		* Battery voltage at least 12.0 V.
	* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) control module.		* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) control module.

RtWiKiSyS0p at 13:54, 19 July 2007

2007-07-19T13:54:00Z

← Older revision		Revision as of 13:54, 19 July 2007
Line 41:		Line 41:


	== ~~Instrument Cluster~~ Swapping ==		== Kessy Control Module Swapping ==

	'''<u>Prerequisites:</u>'''<br>		'''<u>Prerequisites:</u>'''<br>

RtWiKiSyS0p at 13:52, 19 July 2007

2007-07-19T13:52:25Z

← Older revision		Revision as of 13:52, 19 July 2007
Line 56:		Line 56:
	'''[05 - Acc/Start Auth.]'''<br>		'''[05 - Acc/Start Auth.]'''<br>

			'''[Meas. Blocks - 08]'''<br>
	Select Block 024.<br>		Select Block 024.<br>
	'''[Go!]'''<br>		'''[Go!]'''<br>
Line 61:		Line 62:
	* ''If the lock times are NOT '''0''':''		* ''If the lock times are NOT '''0''':''
	** ''Do NOT switch off the ignition!''		** ''Do NOT switch off the ignition!''
	** ''Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-3.''		** ''Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-4.''
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>

Line 91:		Line 92:
	** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".		** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
	'''[Save]'''<br>		'''[Save]'''<br>
			'''[Done, Go Back]'''<br>

			After a successful adaptation a lock time will automatically being set.<br>
			'''[Meas. Blocks - 08]'''<br>
			Select Block 024.<br>
			'''[Go!]'''<br>
			''Make sure the shown lock times in field 4 is '''0''' (a field represents a time in minutes).''<br>
			* ''If the lock time is NOT '''0''':''
			** ''Do NOT switch off the ignition!''
			** ''Allow the car to sit for AT LEAST the number of minutes that were indicated by field 4.''
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>

RtWiKiSyS0p at 13:48, 19 July 2007

2007-07-19T13:48:55Z

← Older revision		Revision as of 13:48, 19 July 2007
Line 22:		Line 22:


	== Determining IMMO-ID & VIN (~~Instrument Cluster~~) ==		== Determining IMMO-ID & VIN (Kessy) ==

	'''[Select]'''<br>		'''[Select]'''<br>