Immobilizer III Key Matching (Cluster) - Revision history

Dana at 18:32, 8 April 2024

2024-04-08T18:32:58Z

← Older revision		Revision as of 18:32, 8 April 2024
Line 62:		Line 62:
	''Any old keys are automatically being cleared. All keys, including existing keys, must be matched at the same time.''<br>		''Any old keys are automatically being cleared. All keys, including existing keys, must be matched at the same time.''<br>
	'''[Save]'''<br>		'''[Save]'''<br>
	~~'''[Done, Go Back]'''<br>~~
	~~'''[Close Controller, Go Back - 06]'''<br>~~

	* ''Repeat the following steps until all Keys have been matched:''		* ''Repeat the following steps until all Keys have been matched:''
Line 71:		Line 69:

	'''Note:''' ''The above steps must be completed within 60 seconds after saving the Adaptation!''		'''Note:''' ''The above steps must be completed within 60 seconds after saving the Adaptation!''

			'''[Done, Go Back]'''<br>
			'''[Close Controller, Go Back - 06]'''<br>

	== Video Link ==		== Video Link ==

Jef at 20:44, 27 August 2020

2020-08-27T20:44:03Z

← Older revision		Revision as of 20:44, 27 August 2020
Line 1:		Line 1:
	__FORCETOC__		__FORCETOC__
	'''This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with with Immobilizer III, where the immobilizer control module is integrated in the instrument cluster. See the seperate instructions for models where the [[Immobilizer III Key Matching (Box)\|immobilizer control module is integrated in a separate immo box]] or where the [[Immobilizer III ~~Immobilizer Swapping~~ (Kessy)\|immobilizer control module is integrated in kessy]] (Keyless Entry and Start SYstem).'''		'''This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with with Immobilizer III, where the immobilizer control module is integrated in the instrument cluster. See the seperate instructions for models where the [[Immobilizer III Key Matching (Box)\|immobilizer control module is integrated in a separate immo box]] or where the [[Immobilizer III Key Matching (Kessy)\|immobilizer control module is integrated in kessy]] (Keyless Entry and Start SYstem).'''

Jef: /* Video Link */

2012-10-08T21:13:17Z

Video Link

← Older revision		Revision as of 21:13, 8 October 2012
Line 73:		Line 73:

	== Video Link ==		== Video Link ==
			=== Immobilizer Gen 2 and 3 Key Adaptation ===
	Immobilizer Gen 2 and 3 Key Adaptation

	[[File:Immobolizer.jpg\|200px\|link=http://www.youtube.com/watch?v=Wj3K04eMV7w]]		[[File:Immobolizer.jpg\|200px\|link=http://www.youtube.com/watch?v=Wj3K04eMV7w]]

	http://www.youtube.com/watch?v=Wj3K04eMV7w		http://www.youtube.com/watch?v=Wj3K04eMV7w

Jef: /* Key Matching */

2012-09-07T18:13:50Z

Key Matching

← Older revision		Revision as of 18:13, 7 September 2012
Line 58:		Line 58:
	Enter 21 in "Channel Number".<br>		Enter 21 in "Channel Number".<br>
	'''[Read]'''<br>		'''[Read]'''<br>
	Enter a "~~New~~ value" corresponding to the total number of keys to be matched, including any existing keys.<br>		''The "Stored Value" is the number of keys currently matched.''<br>
	''~~'[Test]'~~''<br>		Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.<br>
			''Any old keys are automatically being cleared. All keys, including existing keys, must be matched at the same time.''<br>
	'''[Save]'''<br>		'''[Save]'''<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>

	* ''Repeat the following steps until all ~~keys~~ have been matched:''~~<br>~~		* ''Repeat the following steps until all Keys have been matched:''
	**''Switch ~~ignition off~~ and remove ~~key~~.''~~<br>~~		**''Switch Ignition OFF and remove Key.''
	**''Insert next ~~key to ignition~~ and switch ~~ignition on again~~.''~~<br>~~		**''Insert the next Key and switch Ignition ON.''
	**''The ~~warning light for the~~ Immobilizer will light up for ~2 seconds, ~~then go~~ out ~~Switch ignition off and remove~~ key.~~''<br>~~		**''The Immobilizer Warning Light will light up for ~2 seconds, wait until it goes out, indicating that the key has been matched.''

	~~'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!~~''

			'''Note:''' ''The above steps must be completed within 60 seconds after saving the Adaptation!''

	== Video Link ==		== Video Link ==

Jef at 16:43, 7 September 2012

2012-09-07T16:43:57Z

← Older revision		Revision as of 16:43, 7 September 2012
Line 58:		Line 58:
	Enter 21 in "Channel Number".<br>		Enter 21 in "Channel Number".<br>
	'''[Read]'''<br>		'''[Read]'''<br>
	~~''The "Stored Value" is the number of keys currently matched.''<br>~~		Enter a "New value" corresponding to the total number of keys to be matched, including any existing keys.<br>
	Enter a "New value" of ~~0 "zero"~~ to ~~clear out~~ any existing keys. <br>
	'''[Test]'''<br>		'''[Test]'''<br>
	~~Make sure "Test Value" shows 0 "zero"<br>~~
	~~'''[Save]'''<br>~~
	~~'''[Read]''' in Channel 21 again <br>~~
	~~Enter a "New value" corresponding to the total number of keys to be matched, including any existing keys.<br>~~
	'''[Save]'''<br>		'''[Save]'''<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>

Jef: /* Key Matching */

2012-08-27T20:43:16Z

Key Matching

← Older revision		Revision as of 20:43, 27 August 2012
Line 75:		Line 75:

	'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''		'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''


			== Video Link ==

			Immobilizer Gen 2 and 3 Key Adaptation

			[[File:Immobolizer.jpg\|200px\|link=http://www.youtube.com/watch?v=Wj3K04eMV7w]]

			http://www.youtube.com/watch?v=Wj3K04eMV7w

Andy: /* Key Matching */

2012-08-22T16:44:36Z

Key Matching

← Older revision		Revision as of 16:44, 22 August 2012
Line 59:		Line 59:
	'''[Read]'''<br>		'''[Read]'''<br>
	''The "Stored Value" is the number of keys currently matched.''<br>		''The "Stored Value" is the number of keys currently matched.''<br>
	Enter a "~~new~~ value" corresponding to the total number of keys to be matched, including any existing keys.~~<br>~~		Enter a "New value" of 0 "zero" to clear out any existing keys. <br>
	~~''The old keys are automatically being cleared.''~~<br>		'''[Test]'''<br>
			Make sure "Test Value" shows 0 "zero"<br>
			'''[Save]'''<br>
			'''[Read]''' in Channel 21 again <br>
			Enter a "New value" corresponding to the total number of keys to be matched, including any existing keys.<br>
	'''[Save]'''<br>		'''[Save]'''<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>

Jef: /* Key Matching */

2012-07-12T21:36:24Z

Key Matching

← Older revision		Revision as of 21:36, 12 July 2012
Line 50:		Line 50:

	'''[Login - 11]'''<br>		'''[Login - 11]'''<br>
	~~''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''~~
	* '''4-digit PIN'''		* '''4-digit PIN'''
	** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''		** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
	* '''7-digit PIN'''
	** '''[Use 7-digit PIN/SKC]'''
	** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
	** '''[OK]'''
	** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
	'''[Do it!]'''<br>		'''[Do it!]'''<br>

Andy at 19:08, 14 February 2011

2011-02-14T19:08:15Z

← Older revision		Revision as of 19:08, 14 February 2011
Line 66:		Line 66:
	''The "Stored Value" is the number of keys currently matched.''<br>		''The "Stored Value" is the number of keys currently matched.''<br>
	Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.<br>		Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.<br>
	''The old keys are automatically ~~beeing~~ cleared.''<br>		''The old keys are automatically being cleared.''<br>
	'''[Save]'''<br>		'''[Save]'''<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>

RtWiKiSyS0p at 13:35, 14 December 2006

2006-12-14T13:35:11Z

← Older revision		Revision as of 13:35, 14 December 2006
Line 32:		Line 32:

	'''[Select]'''<br>		'''[Select]'''<br>
	'''[25 - ~~Immobilizer~~]'''<br>		'''[17 - Instruments]'''<br>
	'''[Meas. Blocks - 08]'''<br>		'''[Meas. Blocks - 08]'''<br>
	Select Block 022.<br>		Select Block 022.<br>