Immobilizer III Key Matching (Kessy) - Revision history

Jef: /* Key Matching */

2012-07-12T21:38:05Z

Key Matching

← Older revision		Revision as of 21:38, 12 July 2012
Line 45:		Line 45:

	'''[Sec. Access - 16]'''<br>		'''[Sec. Access - 16]'''<br>
	~~''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''~~
	* '''4-digit PIN'''		* '''4-digit PIN'''
	** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''		** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
	* '''7-digit PIN'''		* '''7-digit PIN'''
	** '''[Use 7-digit PIN/SKC]'''
	** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
	** '''[OK]'''
	** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
	'''[Do it!]'''<br>		'''[Do it!]'''<br>

RtWiKiSyS0p at 09:45, 14 June 2011

2011-06-14T09:45:20Z

← Older revision		Revision as of 09:45, 14 June 2011
Line 66:		Line 66:
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>

	*''Switch Ignition OFF and remove Key, Steering Lock should engage.''		* ''Repeat the following steps until all Keys have been matched:''
	*''Insert first Key again and switch Ignition ON.
	*''The Warning Light for the Immobilizer will light up for ~2 seconds, then go out. Switch Ignition OFF and remove Key.''<br>

	* ''Repeat the following steps until all ~~keys~~ have been matched:''
	**''Switch Ignition OFF and remove Key, Steering Lock should engage.''		**''Switch Ignition OFF and remove Key, Steering Lock should engage.''
	**''Insert next Key ~~to Ignition~~ and switch Ignition ON ~~again~~.''		**''Insert the next Key and switch Ignition ON.''
	**''The Warning Light ~~for the Immobilizer~~ will light up for ~2 seconds, ~~then go~~ out~~. Switch Ignition OFF and remove Key~~.''~~<br>~~		**''The Immobilizer Warning Light will light up for ~2 seconds, wait until it goes out.''

	'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds withing matching 2 of the keys and having one key in the ignition should not exceed 30 seconds.!''		'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds withing matching 2 of the keys and having one key in the ignition should not exceed 30 seconds!''

RtWiKiSyS0p at 16:01, 19 July 2007

2007-07-19T16:01:50Z

← Older revision		Revision as of 16:01, 19 July 2007
Line 17:		Line 17:

	'''<u>Prerequisites:</u>'''<br>		'''<u>Prerequisites:</u>'''<br>
	* Battery voltage at least 12.0 V. We strongly recommend the use of a battery charger.		* Battery voltage at least 12.0 V. ''We strongly recommend the use of a battery charger.''
	* You can match up to 8 keys.		* You can match up to 8 keys.
	* All keys are either new or were adapted to this car (IMMO-ID) before.		* All keys are either new or were adapted to this car (IMMO-ID) before.

RtWiKiSyS0p at 16:01, 19 July 2007

2007-07-19T16:01:34Z

← Older revision		Revision as of 16:01, 19 July 2007
Line 17:		Line 17:

	'''<u>Prerequisites:</u>'''<br>		'''<u>Prerequisites:</u>'''<br>
			* Battery voltage at least 12.0 V. We strongly recommend the use of a battery charger.
			* You can match up to 8 keys.
	* All keys are either new or were adapted to this car (IMMO-ID) before.		* All keys are either new or were adapted to this car (IMMO-ID) before.
	* You can match up to 8 keys.
	* While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.''		* While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.''
	* Battery voltage at least 12.0 V. We strongly recommend the use of a battery charger.

	* If all Keys are new OR the first inserted Key is new, the Ignition will NOT switch ON with this key.		* If all Keys are new OR the first inserted Key is new, the Ignition will NOT switch ON with this key.
	** Put the first Key into the ignition Lock, but do NOT switch ON the ignition.		** Put the first Key into the ignition Lock, but do NOT switch ON the ignition.

RtWiKiSyS0p at 16:00, 19 July 2007

2007-07-19T16:00:27Z

← Older revision		Revision as of 16:00, 19 July 2007
Line 21:		Line 21:
	* While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.''		* While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.''
	* Battery voltage at least 12.0 V. We strongly recommend the use of a battery charger.		* Battery voltage at least 12.0 V. We strongly recommend the use of a battery charger.

			* If all Keys are new OR the first inserted Key is new, the Ignition will NOT switch ON with this key.
			** Put the first Key into the ignition Lock, but do NOT switch ON the ignition.
			** Press and Hold the Brake Pedal for 20 Seconds to wake up the Diagnostic Databus.

RtWiKiSyS0p at 15:57, 19 July 2007

2007-07-19T15:57:39Z

← Older revision		Revision as of 15:57, 19 July 2007
Line 65:		Line 65:
	*''Switch Ignition OFF and remove Key, Steering Lock should engage.''		*''Switch Ignition OFF and remove Key, Steering Lock should engage.''
	*''Insert first Key again and switch Ignition ON.		*''Insert first Key again and switch Ignition ON.
	*''The Warning Light for the Immobilizer will light up for ~2 seconds, then go out ~~switch~~ Ignition OFF and remove Key.''<br>		*''The Warning Light for the Immobilizer will light up for ~2 seconds, then go out. Switch Ignition OFF and remove Key.''<br>

	* ''Repeat the following steps until all keys have been matched:''		* ''Repeat the following steps until all keys have been matched:''
	**''Switch Ignition OFF and remove Key, Steering Lock should engage.''		**''Switch Ignition OFF and remove Key, Steering Lock should engage.''
	**''Insert next Key to Ignition and switch Ignition ON again.''		**''Insert next Key to Ignition and switch Ignition ON again.''
	**''The Warning Light for the Immobilizer will light up for ~2 seconds, then go out ~~switch~~ Ignition OFF and remove Key.''<br>		**''The Warning Light for the Immobilizer will light up for ~2 seconds, then go out. Switch Ignition OFF and remove Key.''<br>

	'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds withing matching 2 of the keys and having one key in the ignition should not exceed 30 seconds.!''		'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds withing matching 2 of the keys and having one key in the ignition should not exceed 30 seconds.!''

RtWiKiSyS0p at 15:54, 19 July 2007

2007-07-19T15:54:35Z

← Older revision		Revision as of 15:54, 19 July 2007
Line 58:		Line 58:
	''The "Stored Value" is the number of keys currently matched.''<br>		''The "Stored Value" is the number of keys currently matched.''<br>
	Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.<br>		Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.<br>
	''The old keys are automatically ~~beeing~~ cleared.''<br>		''The old keys are automatically being cleared.''<br>
	'''[Save]'''<br>		'''[Save]'''<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>

	* ''Repeat the following steps until all keys have been matched:''<br>		*''Switch Ignition OFF and remove Key, Steering Lock should engage.''
	**''Switch ~~ignition off~~ and remove ~~key~~.''~~<br>~~		*''Insert first Key again and switch Ignition ON.
	**''Insert ~~next key to ignition~~ and switch ~~ignition on again~~.~~''<br>~~		*''The Warning Light for the Immobilizer will light up for ~2 seconds, then go out switch Ignition OFF and remove Key.''<br>
	**''The ~~warning light~~ for the Immobilizer will light up for ~2 seconds, then go out ~~Switch ignition off~~ and remove ~~key~~.''<br>

	'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''		* ''Repeat the following steps until all keys have been matched:''
			**''Switch Ignition OFF and remove Key, Steering Lock should engage.''
			**''Insert next Key to Ignition and switch Ignition ON again.''
			**''The Warning Light for the Immobilizer will light up for ~2 seconds, then go out switch Ignition OFF and remove Key.''<br>

			'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds withing matching 2 of the keys and having one key in the ignition should not exceed 30 seconds.!''

RtWiKiSyS0p at 15:41, 19 July 2007

2007-07-19T15:41:54Z

← Older revision		Revision as of 15:41, 19 July 2007
Line 3:		Line 3:

	== Determining IMMO-ID & VIN ==		== Determining IMMO-ID & VIN ==

	~~'''[Select]'''<br>~~
	~~'''[05 - Acc/Start Auth.]'''<br>~~
	~~Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.<br>~~
	~~'''[Close Controller, Go Back - 06]'''<br>~~

	~~---OR---~~

	'''[Select]'''<br>		'''[Select]'''<br>
Line 24:		Line 17:

	'''<u>Prerequisites:</u>'''<br>		'''<u>Prerequisites:</u>'''<br>
	* All keys are either new or were adapted to this car (IMMO-ID) before.~~<br>~~		* All keys are either new or were adapted to this car (IMMO-ID) before.
	* You can match up to 8 keys.		* You can match up to 8 keys.
	* While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.''		* While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.''
	* Battery voltage at least 12.0 V.~~<br>~~		* Battery voltage at least 12.0 V. We strongly recommend the use of a battery charger.

RtWiKiSyS0p at 14:00, 19 July 2007

2007-07-19T14:00:01Z

New page

__FORCETOC__
'''This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with with Immobilizer III, where the immobilizer control module is integrated in a separate immo box. See the separate instructions for models where the [[Immobilizer III Key Matching (Cluster)|immobilizer control module is integrated in instrument cluster]] or where the [[Immobilizer III Immobilizer Swapping (Separate)|immobilizer control module is part of a separate Control Module)]].'''

== Determining IMMO-ID & VIN ==

'''[Select]''' 
'''[05 - Acc/Start Auth.]''' 
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID. 
'''[Close Controller, Go Back - 06]''' 

---OR---

'''[Select]''' 
'''[05 - Acc/Start Auth.]''' 
'''[Meas. Blocks - 08]''' 
Select Block 081. 
'''[Go!]''' 
''The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.''. 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]''' 

== Key Matching ==

'''Prerequisites:''' 
* All keys are either new or were adapted to this car (IMMO-ID) before. 
* You can match up to 8 keys.
* While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.''
* Battery voltage at least 12.0 V. 

'''[Select]''' 
'''[05 - Acc/Start Auth.]''' 
'''[Meas. Blocks - 08]''' 
Select Block 022. 
'''[Go!]''' 
''The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.'' 
''You can check each key in this manner.''

Select Block 023. 
'''[Go!]''' 
''Make sure the shown lock times in field 1, 2, 3 and 4 are '''0''' (each field represents a time in minutes).'' 
* ''If the lock times are NOT '''0''':''
** ''Do NOT switch off the ignition!''
** ''Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-4.''
'''[Done, Go Back]''' 

'''[Sec. Access - 16]''' 
''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''
* '''4-digit PIN'''
** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
* '''7-digit PIN'''
** '''[Use 7-digit PIN/SKC]'''
** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
** '''[OK]'''
** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
'''[Do it!]''' 

'''[Adaptation - 10]''' 
Enter 21 in "Channel Number". 
'''[Read]''' 
''The "Stored Value" is the number of keys currently matched.'' 
Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys. 
''The old keys are automatically beeing cleared.'' 
'''[Save]''' 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]''' 

* ''Repeat the following steps until all keys have been matched:'' 
**''Switch ignition off and remove key.'' 
**''Insert next key to ignition and switch ignition on again.'' 
**''The warning light for the Immobilizer will light up for ~2 seconds, then go out Switch ignition off and remove key.'' 

'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''