Immobilizer II Immobilizer Swapping (Instrument Cluster) - Revision history

Jef: /* Instrument Cluster Swapping (Used Cluster) */

2012-07-12T21:24:19Z

Instrument Cluster Swapping (Used Cluster)

← Older revision		Revision as of 21:24, 12 July 2012
Line 20:		Line 20:
	Note: If the 17 Digit VIN is shown the vehicle does not use Immo II and the procedure here does not apply.		Note: If the 17 Digit VIN is shown the vehicle does not use Immo II and the procedure here does not apply.

	== Instrument Cluster Swapping ~~(Used Cluster)~~ ==		== Instrument Cluster Swapping ==

	'''<u>Prerequisites:</u>'''<br>		'''<u>Prerequisites:</u>'''<br>
	* The Coding from the OLD (~~original~~) cluster has been saved.		* The Coding from the OLD (ORIGINAL) cluster has been saved.
	* The NEW (USED) cluster is installed in the car.		* The REPLACEMENT (NEW or USED) cluster is installed in the car.
	* Battery voltage at least 12.0 V.		* Battery voltage at least 12.0 V.
	* All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the NEW (USED) cluster.		* All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the REPLACEMENT (NEW or USED) cluster.
	* Make sure to have the PIN for the NEW (USED) instrument cluster.		* Make sure to have the PIN for the REPLACEMENT (NEW or USED) instrument cluster.
	* Make sure to have the Radio Code (for factory radios only).<br>		* Make sure to have the Radio Code (for factory radios only).<br>

Line 35:		Line 35:
	'''[17 - Instruments]'''<br>		'''[17 - Instruments]'''<br>
	'''[Recode - 07]'''<br>		'''[Recode - 07]'''<br>
	Enter the coding from the OLD (~~original~~) cluster<br>		Enter the coding from the OLD (ORIGINAL) cluster<br>
	'''[Do It!]'''<br>		'''[Do It!]'''<br>

Line 44:		Line 44:
	'''[19 - CAN Gateway]'''<br>		'''[19 - CAN Gateway]'''<br>
	'''[Coding - 07]'''<br>		'''[Coding - 07]'''<br>
	Enter the coding from the OLD (~~original~~) cluster<br>		Enter the coding from the OLD (ORIGINAL) cluster<br>
	'''[Do It!]'''<br>		'''[Do It!]'''<br>

Line 75:		Line 75:
	* Instructions for mileage entry on a new instrument cluster can be found here: [http://www.ross-tech.com/vag-com/cars/Immo2-cluster-swapping.html Procedure for installing a NEW Instrument Cluster in vehicles with Immobilizer II]		* Instructions for mileage entry on a new instrument cluster can be found here: [http://www.ross-tech.com/vag-com/cars/Immo2-cluster-swapping.html Procedure for installing a NEW Instrument Cluster in vehicles with Immobilizer II]
	** Please note the Country Coding and Kilometer -or- Mile units prior to saving the adaptation value!		** Please note the Country Coding and Kilometer -or- Mile units prior to saving the adaptation value!
			** VCDS can not alter or "correct" the odometer reading of a used instrument cluster.

Dana at 20:09, 18 March 2011

2011-03-18T20:09:34Z

← Older revision		Revision as of 20:09, 18 March 2011
Line 3:		Line 3:


	== Determining IMMO-ID ~~& VIN~~ (ECU) ==		== Determining IMMO-ID (ECU) ==

	'''[Select]'''<br>		'''[Select]'''<br>
Line 11:		Line 11:
	Note: If the 17 Digit VIN is shown the vehicle does not use Immo II and the procedure here does not apply.		Note: If the 17 Digit VIN is shown the vehicle does not use Immo II and the procedure here does not apply.

	== Determining IMMO-ID ~~& VIN~~ (Instrument Cluster) ==		== Determining IMMO-ID (Instrument Cluster) ==

	'''[Select]'''<br>		'''[Select]'''<br>

Dana: Created page with 'FORCETOC '''This procedure details how to change the instrument cluster on VW/Audi/Seat/Skoda vehicles with Immobilizer II, where the immobilizer control module is integrated…'

2011-03-18T20:06:14Z

Created page with '__FORCETOC__ '''This procedure details how to change the instrument cluster on VW/Audi/Seat/Skoda vehicles with Immobilizer II, where the immobilizer control module is integrated…'

New page

__FORCETOC__
'''This procedure details how to change the instrument cluster on VW/Audi/Seat/Skoda vehicles with Immobilizer II, where the immobilizer control module is integrated in instrument cluster.'''

== Determining IMMO-ID & VIN (ECU) ==

'''[Select]''' 
'''[01 - Engine]''' 
Look at the first "Extra" field. The 14-digit string is the Immo-ID. 
'''[Close Controller, Go Back - 06]''' 
Note: If the 17 Digit VIN is shown the vehicle does not use Immo II and the procedure here does not apply.

== Determining IMMO-ID & VIN (Instrument Cluster) ==

'''[Select]''' 
'''[17 - Instruments]''' 
Look at the first "Extra" field. The 14-digit string is the Immo-ID. 
'''[Close Controller, Go Back - 06]''' 

Note: If the 17 Digit VIN is shown the vehicle does not use Immo II and the procedure here does not apply.

== Instrument Cluster Swapping (Used Cluster) ==

'''Prerequisites:''' 
* The Coding from the OLD (original) cluster has been saved.
* The NEW (USED) cluster is installed in the car.
* Battery voltage at least 12.0 V.
* All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the NEW (USED) cluster.
* Make sure to have the PIN for the NEW (USED) instrument cluster.
* Make sure to have the Radio Code (for factory radios only). 

=== Coding ===

'''[Select]''' 
'''[17 - Instruments]''' 
'''[Recode - 07]''' 
Enter the coding from the OLD (original) cluster 
'''[Do It!]''' 

'''Additional Volkswagen Step''' ''Including models with an Integral Address 19 - CAN Gateway in the Cluster'' 

'''[Select]''' 
'''[19 - CAN Gateway]''' 
'''[Coding - 07]''' 
Enter the coding from the OLD (original) cluster 
'''[Do It!]''' 

'''Additional Audi Step''' ''Including vehicles that Do Not use an Integral Address 19 - CAN Gateway in the Cluster'' 
Additional Adaptation Channels may be needed for SRI and the Internal Installation List of installed modules. 
* The Internal Installation List channels are generally 060, 061 and 062 when applicable.
* The SRI channels vary by cluster. The automated '''[http://www.ross-tech.com/vcds/tour/sri-reset.html SRI Reset]''' feature of VCDS can be used to check the settings. 

=== Matching the Cluster to the Engine ECU ===

'''[Select]''' 
'''[17 - Instruments]''' 
'''[Adaption - 10]''' 
Leave channel at "00" 
'''[Read]''' 
'''[Save]''' 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]''' 
Switch ignition Off and then back On within one minute, but do not start vehicle. 

Notes: On some Euro Audi models with Immobilizer II, a PIN will be required. 

'''Proceed with [[Immobilizer II Key Matching (Cluster)|Key Matching ''(through Instrument Cluster)'']] now.''' 

==== Special Notes ====

* Instructions for mileage entry on a new instrument cluster can be found here: [http://www.ross-tech.com/vag-com/cars/Immo2-cluster-swapping.html Procedure for installing a NEW Instrument Cluster in vehicles with Immobilizer II]
** Please note the Country Coding and Kilometer -or- Mile units prior to saving the adaptation value!

Immobilizer II Immobilizer Swapping (Instrument Cluster) - Revision history

Jef: /* Instrument Cluster Swapping (Used Cluster) */

Dana at 20:09, 18 March 2011

Dana: Created page with '__FORCETOC__ '''This procedure details how to change the instrument cluster on VW/Audi/Seat/Skoda vehicles with Immobilizer II, where the immobilizer control module is integrated…'

Dana: Created page with 'FORCETOC '''This procedure details how to change the instrument cluster on VW/Audi/Seat/Skoda vehicles with Immobilizer II, where the immobilizer control module is integrated…'