Immobilizer II Key Matching (Cluster) - Revision history

Dana at 18:31, 8 April 2024

2024-04-08T18:31:46Z

← Older revision		Revision as of 18:31, 8 April 2024
Line 26:		Line 26:
	''Any old keys are automatically being cleared. All keys, including existing keys, must be matched at the same time.''<br>		''Any old keys are automatically being cleared. All keys, including existing keys, must be matched at the same time.''<br>
	'''[Save]'''<br>		'''[Save]'''<br>
	~~'''[Done, Go Back]'''<br>~~
	~~'''[Close Controller, Go Back - 06]'''<br>~~

	* ''Repeat the following steps until all Keys have been matched:''		* ''Repeat the following steps until all Keys have been matched:''
Line 36:		Line 34:
	'''Note:''' ''The above steps must be completed within 60 seconds after saving the Adaptation!''		'''Note:''' ''The above steps must be completed within 60 seconds after saving the Adaptation!''

			'''[Done, Go Back]'''<br>
			'''[Close Controller, Go Back - 06]'''<br>

	== Video Link ==		== Video Link ==

Jef: /* Video Link */

2012-10-08T21:12:47Z

Video Link

← Older revision		Revision as of 21:12, 8 October 2012
Line 38:		Line 38:

	== Video Link ==		== Video Link ==
			=== Immobilizer Gen 2 and 3 Key Adaptation ===
	Immobilizer Gen 2 and 3 Key Adaptation

	[[File:Immobolizer.jpg\|200px\|link=http://www.youtube.com/watch?v=Wj3K04eMV7w]]		[[File:Immobolizer.jpg\|200px\|link=http://www.youtube.com/watch?v=Wj3K04eMV7w]]

	http://www.youtube.com/watch?v=Wj3K04eMV7w		http://www.youtube.com/watch?v=Wj3K04eMV7w

Jef: /* Key Matching */

2012-08-27T20:43:20Z

Key Matching

← Older revision		Revision as of 20:43, 27 August 2012
Line 35:		Line 35:

	'''Note:''' ''The above steps must be completed within 60 seconds after saving the Adaptation!''		'''Note:''' ''The above steps must be completed within 60 seconds after saving the Adaptation!''


			== Video Link ==

			Immobilizer Gen 2 and 3 Key Adaptation

			[[File:Immobolizer.jpg\|200px\|link=http://www.youtube.com/watch?v=Wj3K04eMV7w]]

			http://www.youtube.com/watch?v=Wj3K04eMV7w

Jef: /* Key Matching */

2012-07-12T21:10:12Z

Key Matching

← Older revision		Revision as of 21:10, 12 July 2012
Line 14:		Line 14:
	'''[17 - Instruments]'''<br>		'''[17 - Instruments]'''<br>
	'''[Login - 11]'''<br>		'''[Login - 11]'''<br>
	~~''There are two sets of instructions below, according to how you enter the PIN/SKC. Choose the set that applies.''~~
	* '''4-digit PIN'''		* '''4-digit PIN'''
	** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''		** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
	** '''[Do It!]'''		** '''[Do It!]'''
	* '''7-digit PIN'''
	** '''[Use 7-digit PIN/SKC]'''
	** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
	** '''[OK]'''
	** VCDS will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
	** '''[Do It!]'''<br>

Andy at 19:46, 1 February 2012

2012-02-01T19:46:08Z

← Older revision		Revision as of 19:46, 1 February 2012
Line 7:		Line 7:
	'''<u>Prerequisites:</u>'''<br>		'''<u>Prerequisites:</u>'''<br>
	* While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.''		* While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.''
			* You must have all of the keys you intend to be able to use, including the valet key if you have one.
	* Battery voltage at least 12.5 V.<br>		* Battery voltage at least 12.5 V.<br>

Line 13:		Line 14:
	'''[17 - Instruments]'''<br>		'''[17 - Instruments]'''<br>
	'''[Login - 11]'''<br>		'''[Login - 11]'''<br>
	''There are ~~2 possibilities~~ how to enter a PIN~~, choose~~ the ~~one~~ that applies ~~for you~~.''		''There are two sets of instructions below, according to how you enter the PIN/SKC. Choose the set that applies.''
	* '''4-digit PIN'''		* '''4-digit PIN'''
	** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''		** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
			** '''[Do It!]'''
	* '''7-digit PIN'''		* '''7-digit PIN'''
	** '''[Use 7-digit PIN/SKC]'''		** '''[Use 7-digit PIN/SKC]'''
Line 21:		Line 23:
	** '''[OK]'''		** '''[OK]'''
	** VCDS will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".		** VCDS will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
	'''[Do it!]'''<br>		** '''[Do It!]'''<br>


Line 29:		Line 31:
	''The "Stored Value" is the number of keys currently matched.''<br>		''The "Stored Value" is the number of keys currently matched.''<br>
	Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.<br>		Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.<br>
	''~~The~~ old keys are automatically being cleared.''<br>		''Any old keys are automatically being cleared. All keys, including existing keys, must be matched at the same time.''<br>
	'''[Save]'''<br>		'''[Save]'''<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
Line 37:		Line 39:
	**''Switch Ignition OFF and remove Key.''		**''Switch Ignition OFF and remove Key.''
	**''Insert the next Key and switch Ignition ON.''		**''Insert the next Key and switch Ignition ON.''
	**''The Immobilizer Warning Light will light up for ~2 seconds, wait until it goes out.''		**''The Immobilizer Warning Light will light up for ~2 seconds, wait until it goes out, indicating that the key has been matched.''

	'''Note:''' ''The above steps after saving the ~~adaptation, should not exceed 60 seconds~~!''		'''Note:''' ''The above steps must be completed within 60 seconds after saving the Adaptation!''

RtWiKiSyS0p at 10:35, 9 June 2011

2011-06-09T10:35:19Z

← Older revision		Revision as of 10:35, 9 June 2011
Line 34:		Line 34:
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>

	* ''Repeat the following steps until all ~~keys~~ have been matched:''~~<br>~~		* ''Repeat the following steps until all Keys have been matched:''
	**''Switch ~~ignition off~~ and remove ~~key~~.''~~<br>~~		**''Switch Ignition OFF and remove Key.''
	**''Insert next ~~key to ignition~~ and switch ~~ignition on again~~.''~~<br>~~		**''Insert the next Key and switch Ignition ON.''
	**''The ~~warning light for the~~ Immobilizer will light up for ~2 seconds, ~~then go~~ out ~~Switch ignition off and remove key~~.''~~<br>~~		**''The Immobilizer Warning Light will light up for ~2 seconds, wait until it goes out.''

	'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''		'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''

Andy at 21:08, 18 March 2011

2011-03-18T21:08:04Z

← Older revision		Revision as of 21:08, 18 March 2011
Line 20:		Line 20:
	** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.		** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
	** '''[OK]'''		** '''[OK]'''
	** ~~VAG-COM~~ will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".		** VCDS will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
	'''[Do it!]'''<br>		'''[Do it!]'''<br>

Andy at 21:06, 18 March 2011

2011-03-18T21:06:06Z

← Older revision		Revision as of 21:06, 18 March 2011
Line 1:		Line 1:
	__FORCETOC__		__FORCETOC__
	'''This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with Immobilizer II, where the immobilizer control module is integrated in the instrument cluster.'''		'''This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with Immobilizer II, where the immobilizer control module is integrated in the instrument cluster. For help determining which Immobilizer system is in each vehicle and for applicable procedures for other types of Immobilizer, go to the general [[Immobilizer]] page.'''

Dana: Created page with 'FORCETOC '''This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with Immobilizer II, where the immobilizer control module is integrated in the instrum…'

2011-03-18T20:56:28Z

Created page with '__FORCETOC__ '''This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with Immobilizer II, where the immobilizer control module is integrated in the instrum…'

New page

__FORCETOC__
'''This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with Immobilizer II, where the immobilizer control module is integrated in the instrument cluster.'''

== Key Matching ==

'''Prerequisites:''' 
* While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.''
* Battery voltage at least 12.5 V. 

'''[Select]''' 
'''[17 - Instruments]''' 
'''[Login - 11]''' 
''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''
* '''4-digit PIN'''
** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
* '''7-digit PIN'''
** '''[Use 7-digit PIN/SKC]'''
** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
** '''[OK]'''
** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
'''[Do it!]''' 

'''[Adaptation - 10]''' 
Enter 21 in "Channel Number". 
'''[Read]''' 
''The "Stored Value" is the number of keys currently matched.'' 
Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys. 
''The old keys are automatically being cleared.'' 
'''[Save]''' 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]''' 

* ''Repeat the following steps until all keys have been matched:'' 
**''Switch ignition off and remove key.'' 
**''Insert next key to ignition and switch ignition on again.'' 
**''The warning light for the Immobilizer will light up for ~2 seconds, then go out Switch ignition off and remove key.'' 

'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''

Immobilizer II Key Matching (Cluster) - Revision history

Dana at 18:31, 8 April 2024

Jef: /* Video Link */

Jef: /* Key Matching */

Jef: /* Key Matching */

Andy at 19:46, 1 February 2012

RtWiKiSyS0p at 10:35, 9 June 2011

Andy at 21:08, 18 March 2011

Andy at 21:06, 18 March 2011

Dana: Created page with '__FORCETOC__ '''This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with Immobilizer II, where the immobilizer control module is integrated in the instrum…'

Dana: Created page with 'FORCETOC '''This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with Immobilizer II, where the immobilizer control module is integrated in the instrum…'