Immobilizer IV Immobilizer Swapping (Instrument Cluster) - Revision history

Dana at 19:42, 3 June 2024

2024-06-03T19:42:21Z

← Older revision		Revision as of 19:42, 3 June 2024
Line 1:		Line 1:
	__FORCETOC__		__FORCETOC__
	'''This procedure details how to change the instrument cluster on VW/Audi/Seat/Skoda vehicles with Immobilizer IV, where the immobilizer control module is integrated in instrument cluster. See the ~~seperate~~ instructions for models where the [[Immobilizer IV Immobilizer Swapping (Kessy)\|immobilizer control module is integrated in kessy]] (Keyless Entry and Start SYstem).'''		'''This procedure details how to change the instrument cluster on VW/Audi/Seat/Skoda vehicles with Immobilizer IV, where the immobilizer control module is integrated in instrument cluster. See the separate instructions for models where the [[Immobilizer IV Immobilizer Swapping (Kessy)\|immobilizer control module is integrated in kessy]] (Keyless Entry and Start SYstem).'''


Line 65:		Line 65:
	* Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.		* Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
	* Verify that the NEW (USED) instrument cluster now shows the VIN/IMMO-ID of the vehicle now.		* Verify that the NEW (USED) instrument cluster now shows the VIN/IMMO-ID of the vehicle now.
			* '''Proceed with [[Immobilizer IV Key Matching\|Key Matching]] now.'''


	* '''Proceed with [[~~Immobilizer IV Key Matching\|Key Matching~~]] ~~now~~.~~'''~~		== Special Notes ==
			If Adaptation Channel 050 is not saving when the PIN is confirmed to be correct make sure the WSC/Importer/Equipment numbers are NOT all zeros before clicking Save. If address 25-Immobilizer shows all zero details (Shop #: WSC 00000 000 00000) in the Auto-Scan after failed matching they can be changed on the VCDS program [https://www.ross-tech.com/vcds/tour/option_screen.php#WSC [Options]] screen. Any value that is not all zeros or ones should work.

Jef: /* Instrument Cluster Swapping (Used Cluster) */

2012-07-12T22:10:43Z

Instrument Cluster Swapping (Used Cluster)

← Older revision		Revision as of 22:10, 12 July 2012
Line 43:		Line 43:
	'''[Security Access - 16]'''<br>		'''[Security Access - 16]'''<br>
	''For the following procedure, '''use the PIN of the NEW (USED)''' instrument cluster.''<br>		''For the following procedure, '''use the PIN of the NEW (USED)''' instrument cluster.''<br>
	~~''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''<br>~~
	* '''4-digit PIN'''		* '''4-digit PIN'''
	** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''		** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
	* '''7-digit PIN'''
	** '''[Use 7-digit PIN/SKC]'''
	** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
	** '''[OK]'''
	** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
	'''[Do it!]'''<br>		'''[Do it!]'''<br>

Line 61:		Line 55:
	'''[Read]'''<br>		'''[Read]'''<br>
	''For the following procedure, '''use the PIN of the OLD (ORIGINAL)''' instrument cluster.''<br>		''For the following procedure, '''use the PIN of the OLD (ORIGINAL)''' instrument cluster.''<br>
	~~''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''<br>~~
	* '''4-digit PIN'''		* '''4-digit PIN'''
	** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''		** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
	* '''7-digit PIN'''
	** '''[Use 7-digit PIN/SKC]'''
	** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
	** '''[OK]'''
	** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
	'''[Test]'''<br>		'''[Test]'''<br>
	'''[Save]'''<br>		'''[Save]'''<br>

RtWiKiSyS0p at 19:41, 29 April 2007

2007-04-29T19:41:39Z

← Older revision		Revision as of 19:41, 29 April 2007
Line 69:		Line 69:
	** '''[OK]'''		** '''[OK]'''
	** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".		** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
			'''[Test]'''<br>
	'''[Save]'''<br>		'''[Save]'''<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>

RtWiKiSyS0p at 13:31, 1 June 2006

2006-06-01T13:31:21Z

← Older revision		Revision as of 13:31, 1 June 2006
Line 1:		Line 1:
	__FORCETOC__		__FORCETOC__
	This procedure details how to change the instrument cluster on VW/Audi/Seat/Skoda vehicles with Immobilizer IV.		'''This procedure details how to change the instrument cluster on VW/Audi/Seat/Skoda vehicles with Immobilizer IV, where the immobilizer control module is integrated in instrument cluster. See the seperate instructions for models where the [[Immobilizer IV Immobilizer Swapping (Kessy)\|immobilizer control module is integrated in kessy]] (Keyless Entry and Start SYstem).'''


	== Determining IMMO-ID & VIN (ECU) ==		== Determining IMMO-ID & VIN (ECU) ==

RtWiKiSyS0p at 13:22, 1 June 2006

2006-06-01T13:22:00Z

← Older revision		Revision as of 13:22, 1 June 2006
Line 30:		Line 30:
	'''<u>Prerequisites:</u>'''<br>		'''<u>Prerequisites:</u>'''<br>
	* The NEW (USED) cluster is installed in the car.		* The NEW (USED) cluster is installed in the car.
	* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) instrument cluster.
	* Battery voltage at least 12.0 V.		* Battery voltage at least 12.0 V.
	* All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the NEW (USED) cluster.		* All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the NEW (USED) cluster.
			* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) instrument cluster.
			* Make sure to have the Radio Code (for factory radios only).


Line 50:		Line 51:
	** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".		** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
	'''[Do it!]'''<br>		'''[Do it!]'''<br>


			* ''The instrument cluster now shows '''Immobilizer Adaptation active''', wait until it changes to '''Immobilizer active''' - this may take up to 2 Minutes.''

RtWiKiSyS0p at 13:08, 1 June 2006

2006-06-01T13:08:30Z

← Older revision		Revision as of 13:08, 1 June 2006
Line 33:		Line 33:
	* Battery voltage at least 12.0 V.		* Battery voltage at least 12.0 V.
	* All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the NEW (USED) cluster.		* All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the NEW (USED) cluster.


	'''[Select]'''<br>		'''[Select]'''<br>

RtWiKiSyS0p at 13:08, 1 June 2006

2006-06-01T13:08:22Z

← Older revision		Revision as of 13:08, 1 June 2006
Line 31:		Line 31:
	* The NEW (USED) cluster is installed in the car.		* The NEW (USED) cluster is installed in the car.
	* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) instrument cluster.		* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) instrument cluster.
	* Battery voltage at least 12.0 V.~~<br>~~		* Battery voltage at least 12.0 V.
			* All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the NEW (USED) cluster.

	'''[Select]'''<br>		'''[Select]'''<br>

RtWiKiSyS0p at 13:05, 1 June 2006

2006-06-01T13:05:04Z

← Older revision		Revision as of 13:05, 1 June 2006
Line 29:		Line 29:

	'''<u>Prerequisites:</u>'''<br>		'''<u>Prerequisites:</u>'''<br>
	* The ~~new~~ (~~used~~) cluster is installed in the car.		* The NEW (USED) cluster is installed in the car.
	* ~~You do~~ have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) instrument cluster.		* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) instrument cluster.
	* Battery voltage at least 12.0 V.<br>		* Battery voltage at least 12.0 V.<br>

RtWiKiSyS0p at 13:04, 1 June 2006

2006-06-01T13:04:23Z

← Older revision		Revision as of 13:04, 1 June 2006
Line 70:		Line 70:
	* Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.		* Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
	* Verify that the NEW (USED) instrument cluster now shows the VIN/IMMO-ID of the vehicle now.		* Verify that the NEW (USED) instrument cluster now shows the VIN/IMMO-ID of the vehicle now.


			* '''Proceed with [[Immobilizer IV Key Matching\|Key Matching]] now.'''

RtWiKiSyS0p at 13:03, 1 June 2006

2006-06-01T13:03:19Z

← Older revision		Revision as of 13:03, 1 June 2006
Line 24:		Line 24:
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>


			== Instrument Cluster Swapping (Used Cluster) ==

			'''<u>Prerequisites:</u>'''<br>
			* The new (used) cluster is installed in the car.
			* You do have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) instrument cluster.
			* Battery voltage at least 12.0 V.<br>


			'''[Select]'''<br>
			'''[25 - Immobilizer]'''<br>


			'''[Security Access - 16]'''<br>
			''For the following procedure, '''use the PIN of the NEW (USED)''' instrument cluster.''<br>
			''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''<br>
			* '''4-digit PIN'''
			** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
			* '''7-digit PIN'''
			** '''[Use 7-digit PIN/SKC]'''
			** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
			** '''[OK]'''
			** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
			'''[Do it!]'''<br>


			'''[Adaptation - 10]'''<br>
			Enter 050 in "Channel Number".<br>
			'''[Read]'''<br>
			''For the following procedure, '''use the PIN of the OLD (ORIGINAL)''' instrument cluster.''<br>
			''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''<br>
			* '''4-digit PIN'''
			** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
			* '''7-digit PIN'''
			** '''[Use 7-digit PIN/SKC]'''
			** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
			** '''[OK]'''
			** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
			'''[Save]'''<br>
			'''[Done, Go Back]'''<br>
			'''[Close Controller, Go Back - 06]'''<br>


			* Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
			* Verify that the NEW (USED) instrument cluster now shows the VIN/IMMO-ID of the vehicle now.