Andy: /* Manually Generating Readiness */

2006-10-05T20:50:53Z

Manually Generating Readiness

← Older revision		Revision as of 20:50, 5 October 2006
Line 24:		Line 24:
	Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.<br>		Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.<br>
	'''[Switch to Meas. Blocks]'''<br>		'''[Switch to Meas. Blocks]'''<br>


	~~''Transmission kickdown (applies to Auto Trans vehicles only!)''<br>~~

	~~Select group 063<br>~~
	~~'''[Go]'''<br>~~
	~~'''[Switch to basic settings]'''<br>~~
	~~Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.<br>~~
	~~'''[Switch to Meas. Blocks]'''<br>~~


	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Close Controller, Go Back]'''<br>		'''[Close Controller, Go Back]'''<br>
Line 48:		Line 37:
	'''[01 - Engine]'''<br>		'''[01 - Engine]'''<br>
	'''[Measuring Blocks - 08]'''<br>		'''[Measuring Blocks - 08]'''<br>
	Select group ~~071~~<br>		Select group 202<br>
	'''[Go]'''<br>		'''[Go]'''<br>
	'''[Switch to basic settings]'''<br>		'''[Switch to basic settings]'''<br>
	Leave it in Basic Settings until the fourth field reads ~~Syst.OK~~<br>		Leave it in Basic Settings until the fourth field reads xxxxx100<br>
	'''[Switch to Meas. Blocks]'''<br>		'''[Switch to Meas. Blocks]'''<br>

Andy at 20:48, 5 October 2006

2006-10-05T20:48:34Z

New page

=== Manually Generating Readiness ===

* Ignition ON and Engine OFF 

''Reading and clearing fault codes'' 

'''[Select]''' 
'''[01 - Engine]''' 
'''[Fault Codes - 02]''' 
'''[Clear Codes -05]''' 
'''[Done, Go Back]''' 

''Throttle Body Alignment'' 

'''[Measuring Blocks - 08]''' 
Select group 060 
'''[Go]''' 
'''[Switch to basic settings]''' 
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK. 
'''[Switch to Meas. Blocks]''' 

''Transmission kickdown (applies to Auto Trans vehicles only!)'' 

Select group 063 
'''[Go]''' 
'''[Switch to basic settings]''' 
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK. 
'''[Switch to Meas. Blocks]''' 

'''[Done, Go Back]''' 
'''[Close Controller, Go Back]''' 

* Ignition ON and Engine ON at idle 

''Fuel leakage test'' 

'''[Select]''' 
'''[01 - Engine]''' 
'''[Measuring Blocks - 08]''' 
Select group 071 
'''[Go]''' 
'''[Switch to basic settings]''' 
Leave it in Basic Settings until the fourth field reads Syst.OK 
'''[Switch to Meas. Blocks]''' 

''Evap purge test'' 

Select group 070 
'''[Go]''' 
'''[Switch to basic settings]''' 
Leave it in Basic Settings until the fourth field reads EVAP OK 
'''[Switch to Meas. Blocks]''' 

''A/F control test'' 

Select group 107 
'''[Go]''' 
'''[Switch to basic settings]''' 
Leave it in Basic Settings until the fourth field reads Syst.OK 
'''[Switch to Meas. Blocks]''' 

* Ignition ON and Engine ON between 1800 and 2200 rpm 

''O2 sensor heater test'' 

Select group 041 
'''[Go]''' 
'''[Switch to basic settings]''' 
Leave it in Basic Settings until there are kOhm readings in the first and third fields 
'''[Switch to Meas. Blocks]''' 
Select group 042 
'''[Go]''' 
'''[Switch to basic settings]''' 
Leave it in Basic Settings until there are kOhm readings in the first and third fields 
'''[Switch to Meas. Blocks]''' 

* Ignition ON and Engine ON at idle 

''Post-cat O2 sensors readiness test'' 

Select group 036 
'''[Go]''' 
'''[Switch to basic settings]''' 
Leave it in Basic Settings until you see B1-S2 OK in the first field and B2-S2 OK in the third field 
'''[Switch to Meas. Blocks]''' 

* Ignition ON and Engine ON between 1520 and 2280 rpm 

''Pre-cat O2 sensors response time test'' 

Select group 034 
'''[Go]''' 
'''[Switch to basic settings]''' 
Leave it in Basic Settings until the fourth field reads B1-S1 OK 
'''[Switch to Meas. Blocks]''' 
Select group 035 
'''[Go]''' 
'''[Switch to basic settings]''' 
Leave it in Basic Settings until the fourth field reads B2-S1 OK 
'''[Switch to Meas. Blocks]''' 

* Ignition ON and Engine ON at idle 

''O2 sensor control test'' 

Select group 037 
'''[Go]''' 
'''[Switch to basic settings]''' 
Leave it in Basic Settings until the fourth field reads Syst. OK 
'''[Switch to Meas. Blocks]''' 
Select group 038 
'''[Go]''' 
'''[Switch to basic settings]''' 
Leave it in Basic Settings until the fourth field reads Syst. OK 
'''[Switch to Meas. Blocks]''' 

''Post-cat O2 sensor aging test'' 

Select group 043 
'''[Go]''' 
'''[Switch to basic settings]''' 
Leave it in Basic Settings until the fourth field reads B1-S2 OK 
'''[Switch to Meas. Blocks]''' 
Select group 044 
'''[Go]''' 
'''[Switch to basic settings]''' 
Leave it in Basic Settings until the fourth field reads B2-S2 OK 
'''[Switch to Meas. Blocks]''' 

* Ignition ON and Engine ON between 1880 and 2280 rpm 

''Catalytic converter test'' 

Select group 046 
'''[Go]''' 
'''[Switch to basic settings]''' 
Leave it in Basic Settings until the fourth field reads CAT B1 OK 
'''[Switch to Meas. Blocks]''' 
Select group 047 
'''[Go]''' 
'''[Switch to basic settings]''' 
Leave it in Basic Settings until the fourth field reads CAT B2 OK 
'''[Switch to Meas. Blocks]''' 

* Ignition ON and Engine ON at idle 

''Secondary air injection test (applies to Auto Trans vehicles only!)'' 

Select group 077 
'''[Go]''' 
'''[Switch to basic settings]''' 
Leave it in Basic Settings until the fourth field reads Syst. OK 
'''[Switch to Meas. Blocks]''' 
Select group 078 
'''[Go]''' 
'''[Switch to basic settings]''' 
Leave it in Basic Settings until the fourth field reads Syst. OK 
'''[Switch to Meas. Blocks]''' 
'''[Done, Go Back]''' 

''Checking Readiness'' 
'''[Readiness]''' 
Make sure none of the fields say Failed or Incomplete 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back]''' 

You're done!

Readiness - AXK Engine Code - Revision history

Andy: /* Manually Generating Readiness */

Andy at 20:48, 5 October 2006