VW Golf/Jetta/Bora (1K/5M) Tweaks - Revision history

Dana: /* [17] - Instrument Cluster */

2011-11-07T14:57:30Z

[17] - Instrument Cluster

← Older revision		Revision as of 14:57, 7 November 2011
Line 93:		Line 93:
	''Unlike the 09 and 46 modules the Instrument Cluster uses conventional Short coding. The coding is the sum of numbers that need added or subtracted from the proper position(s)''. <br>		''Unlike the 09 and 46 modules the Instrument Cluster uses conventional Short coding. The coding is the sum of numbers that need added or subtracted from the proper position(s)''. <br>

	~~Look~~ at the third and fourth digits in the coding (00??x0x). Add the values for the options together and put them in the third and fourth digit location to get the correct coding.<br>		Using a 1K chassis VW example we'll look at the third and fourth digits in the coding (00??x0x). Add the values for the options together and put them in the third and fourth digit location to get the correct coding:<br>

	00 - No available equipment<br>		00 - No available equipment<br>
Line 101:		Line 101:
	+16 - Sedan (Jetta)<br>		+16 - Sedan (Jetta)<br>

	So, if your stock Soft Coding is 0023203 and you want to remove the seatbelt chime, put in a new value of 0021203.<br>		So, if your stock Soft Coding is 0023203 and you want to remove the seatbelt chime, put in a new value of 0021203. If the coding chart in VCDS does not match the above example use the information available in the pop-up balloon. <br>

	* Additional "Seatbelt Warning" options may be available under '''[Adaptation - 10]'''		* Additional "Seatbelt Warning" options may be available under '''[Adaptation - 10]'''

Andy at 14:56, 19 October 2011

2011-10-19T14:56:59Z

← Older revision		Revision as of 14:56, 19 October 2011
Line 5:		Line 5:
	'''These instructions apply to the [[VW Golf/Jetta/Bora (1K/5M)]]''' and most of the 2009 and older [[Audi A3/S3 & A3 Cabriolet (8P)]] chassis vehicles.		'''These instructions apply to the [[VW Golf/Jetta/Bora (1K/5M)]]''' and most of the 2009 and older [[Audi A3/S3 & A3 Cabriolet (8P)]] chassis vehicles.

	''Note: For many ~~20010~~ and newer vehicles, including the [[VW Golf/Golf Plus (5K/52)]] + and the 2010 [[VW Golf/Golf Plus (5K/52)\|VW Jetta (1K/AJ)]] models, a newer 09-Central Electronics module (BCM) replaces the previous generation 46-Central Conv. module. Those models are not covered on this page.''		''Note: For many 2010 and newer vehicles, including the [[VW Golf/Golf Plus (5K/52)]] + and the 2010 [[VW Golf/Golf Plus (5K/52)\|VW Jetta (1K/AJ)]] models, a newer 09-Central Electronics module (BCM) replaces the previous generation 46-Central Conv. module. Those models are not covered on this page.''

	* It is always recommended to perform a complete Auto-Scan and save it prior to coding changes. Please see the Online Manual: [http://www.ross-tech.com/vcds/tour/autoscan.html Auto Scan Screen]		* It is always recommended to perform a complete Auto-Scan and save it prior to coding changes. Please see the Online Manual: [http://www.ross-tech.com/vcds/tour/autoscan.html Auto Scan Screen]

Dana at 21:48, 5 October 2011

2011-10-05T21:48:23Z

← Older revision		Revision as of 21:48, 5 October 2011
Line 3:		Line 3:
	'''Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk'''.<br>		'''Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk'''.<br>

	'''These instructions apply to the [[VW Golf/Jetta/Bora (1K/5M)]].'''		'''These instructions apply to the [[VW Golf/Jetta/Bora (1K/5M)]]''' and most of the 2009 and older [[Audi A3/S3 & A3 Cabriolet (8P)]] chassis vehicles.

	''Note: For many 20010 and newer vehicles, including the [[VW Golf/Golf Plus (5K/52)]] + and the 2010 [[VW Golf/Golf Plus (5K/52)\|VW Jetta (1K/AJ)]] models, a newer 09-Central Electronics module (BCM) replaces the previous generation 46-Central Conv. module. Those models are not covered on this page.''		''Note: For many 20010 and newer vehicles, including the [[VW Golf/Golf Plus (5K/52)]] + and the 2010 [[VW Golf/Golf Plus (5K/52)\|VW Jetta (1K/AJ)]] models, a newer 09-Central Electronics module (BCM) replaces the previous generation 46-Central Conv. module. Those models are not covered on this page.''

Dana at 02:52, 18 August 2011

2011-08-18T02:52:31Z

@@ Line 131: / Line 131: @@
 * Check the box for "Comfort closing power windows via remote control active"<br>
 * Check the box for "Closing sunroof via remote control active"<br>
-Note, For some reason, VW does not allow the sunroof to be opened using the remote, only closed, despite the presence of a checkbox indication for that feature.<br>
+Notes:
 === Alarm and Locking ===

Dana at 19:22, 25 April 2011

2011-04-25T19:22:29Z

← Older revision		Revision as of 19:22, 25 April 2011
Line 20:		Line 20:
	=== Lighting ===		=== Lighting ===

	All modifications are found in Found in '''[Coding - 07]''' > '''[http://www.ross-tech.com/vcds/tour/recode_screen.html Long Coding Helper]''' unless otherwise noted. Click on each of the Bytes and Bits for the documented options and check ~~and~~ un-check the appropriate boxes. <br>		All modifications are found in Found in '''[Coding - 07]''' > '''[http://www.ross-tech.com/vcds/tour/recode_screen.html Long Coding Helper]''' unless otherwise noted. Click on each of the Bytes and Bits for the documented options and check or un-check the appropriate boxes as shown in the example below:<br>

			'''[Select]'''<br>
			'''[09 - Cent. Elect.]''' ''Or the module you intend on tweaking as per the list below''<br>
			'''[Coding - 07]'''<br>
			'''[Long Coding Helper]'''<br>
			Click on each of the Byte numbers in row '''3''') and you'll see the selectable options below. Check or Un-check the boxes for the desired results. ''Example: Daytime Running Lights (North America)''<br>
			Close the Long Coding Helper by clicking the Windows X box on the top right of the screen or clicking the Exit button on the top left of the screen to send your altered Coding value back to the Coding screen.<br>
			'''[Do It!]'''<br>
			.<br>

	'''Daytime Running Lights''' - The systems are coded differently depending on the market:		'''Daytime Running Lights''' - The systems are coded differently depending on the market:

Dana at 03:36, 24 April 2011

2011-04-24T03:36:34Z

@@ Line 57: / Line 57: @@
 '''Emergency Brake Warning active''' ''The Brake Lights should flash under Panic stopping conditions.''<br>
-* Enable "Emergency Brake Flash Light active"
+* Enable "Emergency Brake Flash Light active"<br>
 === [17] - Instrument Cluster ===
@@ Line 91: / Line 109: @@
 ** Fuel gauge adaptation <br>
 === [46] - Comfort System ===
@@ Line 104: / Line 124: @@
 * Check the box for "Closing sunroof via remote control active"<br>
 Note, For some reason, VW does not allow the sunroof to be opened using the remote, only closed, despite the presence of a checkbox indication for that feature.<br>

Dana at 22:25, 23 March 2011

2011-03-23T22:25:42Z

← Older revision		Revision as of 22:25, 23 March 2011
Line 5:		Line 5:
	'''These instructions apply to the [[VW Golf/Jetta/Bora (1K/5M)]].'''		'''These instructions apply to the [[VW Golf/Jetta/Bora (1K/5M)]].'''

	''Note: For many ~~2009~~ and newer vehicles, including the [[VW Golf/Golf Plus (5K/52)]] models, a newer 09-Central Electronics module (BCM) replaces the previous generation 46-Central Conv. module. Those models are not covered on this page.''		''Note: For many 20010 and newer vehicles, including the [[VW Golf/Golf Plus (5K/52)]] + and the 2010 [[VW Golf/Golf Plus (5K/52)\|VW Jetta (1K/AJ)]] models, a newer 09-Central Electronics module (BCM) replaces the previous generation 46-Central Conv. module. Those models are not covered on this page.''

	* It is always recommended to perform a complete Auto-Scan and save it prior to coding changes. Please see the Online Manual: [http://www.ross-tech.com/vcds/tour/autoscan.html Auto Scan Screen]		* It is always recommended to perform a complete Auto-Scan and save it prior to coding changes. Please see the Online Manual: [http://www.ross-tech.com/vcds/tour/autoscan.html Auto Scan Screen]
Line 11:		Line 11:


	''The installed control modules vary by vendor, firmware level and equipment level, some of the noted tweaks may not be supported by all control modules/vehicles.''<br>		''The installed control modules vary by vendor, firmware level and equipment level, some of the noted tweaks may not be supported by all control modules / vehicles.''<br>

	----		----

Dana: Created page with 'FORCETOC '''Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk'''.
'''These…'

2011-03-22T23:54:43Z

Created page with '__FORCETOC__ '''Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk'''. '''These…'

New page

__FORCETOC__

'''Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk'''. 

'''These instructions apply to the [[VW Golf/Jetta/Bora (1K/5M)]].'''

''Note: For many 2009 and newer vehicles, including the [[VW Golf/Golf Plus (5K/52)]] models, a newer 09-Central Electronics module (BCM) replaces the previous generation 46-Central Conv. module. Those models are not covered on this page.''

* It is always recommended to perform a complete Auto-Scan and save it prior to coding changes. Please see the Online Manual: [http://www.ross-tech.com/vcds/tour/autoscan.html Auto Scan Screen]
* Never Copy coding from a different vehicle and Paste it to your module(s)! 

''The installed control modules vary by vendor, firmware level and equipment level, some of the noted tweaks may not be supported by all control modules/vehicles.'' 

----

=== [09] - Central Electronics ===

=== Lighting ===

All modifications are found in Found in '''[Coding - 07]''' > '''[http://www.ross-tech.com/vcds/tour/recode_screen.html Long Coding Helper]''' unless otherwise noted. Click on each of the Bytes and Bits for the documented options and check and un-check the appropriate boxes. 

'''Daytime Running Lights''' - The systems are coded differently depending on the market:
* "Daytime Running Lights (Scandinavia) active" should result in ALL exterior lights running
* "Daytime Running Lights (North America)" should result in headlights Only lights running 

'''Fogs as Daytime Running Lights''' ''when applicable'' 
* Enable "Daytime Running Light via Fog Lights" 

'''Daytime Running Lights Dimming''''' If DRLs are Halogen bulbs (not Xenon) the dimming resolution may be adjusted.'' 
* Select the Byte with "Daytime Running Lights Dimming" "Decimal Value (Resolution: 1%)" and alter the value. 
* Additional Light Dimming bits are available for other lighting circuits. 

'''Front and /or Rear Fog Light dimming behavior with High Beams or Trailer''' 
''Depending on equipment level, additional coding bits may be available.'' 
* Front Fog Lights deactivated with High Beam
* Rear Fog Light Deactivation with Trailer active

'''Cornering Lights via Front Fog Lights active''' ''when applicable'' 
* Enable "Internal Turn Light Control Algorithm active" 
* Next, Enable "Turn Lights via Fog Lights" 
* Additional '''[Adaptation - 10]''' options may be available for dimming duration activation/deactivation 
Notes: After Cornering Lights via Front Fog Lights is active, the lights may work under the following conditions:
* The headlights must be turned on and the steering wheel must be in the turning direction.
* The headlights must be turned on and the turn signal must be on in the turning direction. 

'''Comfort Turn signals''' 
* Comfort Turn signals may be turned On -or- Off via coding. The number of flashes cannot be adjusted. 

'''Emergency Brake Warning active''' ''The Brake Lights should flash under Panic stopping conditions.'' 
* Enable "Emergency Brake Flash Light active"

=== [17] - Instrument Cluster ===

'''Seatbelt Chime''' ''May remove the light as well'' 
* Found in '''[Coding - 07].''' 
''Unlike the 09 and 46 modules the Instrument Cluster uses conventional Short coding. The coding is the sum of numbers that need added or subtracted from the proper position(s)''. 

Look at the third and fourth digits in the coding (00??x0x). Add the values for the options together and put them in the third and fourth digit location to get the correct coding. 

00 - No available equipment 
+01 - Brakepad wear sensor warning active 
+02 - Seatbelt warning active 
+04 - Washer fluid level warning active 
+16 - Sedan (Jetta) 

So, if your stock Soft Coding is 0023203 and you want to remove the seatbelt chime, put in a new value of 0021203. 

* Additional "Seatbelt Warning" options may be available under '''[Adaptation - 10]'''

'''Modify Service Intervals Mileage and Time''' 
* Found in '''[Adaptation - 10].''' 
''Depending on the vehicle configuration, options for Min. Distance and Time to service may be altered''. 
* The '''[http://www.ross-tech.com/vcds/tour/sri-reset.html [SRI Reset]]''' function is used for normal Service Reset procedures.

'''Fuel Gauge and Fuel Consumption Adaption''' ''when applicable'' 
* Found in '''[Adaptation - 10].''' 
** Consumption Correction 
** Fuel gauge adaptation 

=== [46] - Comfort System ===

=== Windows ===

Found in '''[Coding - 07]''' > '''[http://www.ross-tech.com/vcds/tour/recode_screen.html Long Coding Helper]'''

'''Windows up via remote''' ''Comfort Operation (via Remote Control) '' 
* Uncheck the box for "Comfort function power windows/sunroof via remote control inactive" 
* Check the box for "Comfort opening power windows via remote control active" 
* Check the box for "Comfort closing power windows via remote control active" 
* Check the box for "Closing sunroof via remote control active" 
Note, For some reason, VW does not allow the sunroof to be opened using the remote, only closed, despite the presence of a checkbox indication for that feature.