VW Golf (1J) Brake Electronics (MK20) - Revision history

Dana at 18:15, 16 August 2017

2017-08-16T18:15:21Z

← Older revision		Revision as of 18:15, 16 August 2017
Line 2:		Line 2:

	== Coding ==		== Coding ==
			* Due to all of the Coding MK20 variants, it is recommended to use the coding from the original module when replacing the ABS module. Save the complete [http://www.ross-tech.com/vcds/tour/autoscan.html Auto-Scan] before repairs.
			* If you are having trouble finding/calculating the proper Coding please:
			** Refer to the [http://wiki.ross-tech.com/wiki/index.php/Official_Factory_Repair_Information Factory Repair Manual] for Coding information.
			** Registered users that need assistance configuring the Coding can send the before and after replacement Auto-Scans to [mailto:Support@Ross-Tech.com Support] for assistance.

	* '''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but may automatically be shown once you access the Coding Function using VCDS (provided the necessary label file with documentation is present).''' ''If you are having trouble finding/calculating the proper Coding please Refer to the Factory Repair Manual or [http://ross-tech.com/contact.html Contact us directly].''

	== Basic Setting ==		== Basic Setting ==

Peter: /* Longitudinal Acceleration Sensor (G251) */

2015-05-08T15:42:08Z

Longitudinal Acceleration Sensor (G251)

← Older revision		Revision as of 15:42, 8 May 2015
Line 109:		Line 109:
	After a successful basic setting, field 2 should say "OK".<br>		After a successful basic setting, field 2 should say "OK".<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	To make sure the basic setting was ~~succesful~~, check the sensor again.<br>		To make sure the basic setting was successful, check the sensor again.<br>
	'''[Measuring Blocks - 08]'''<br>		'''[Measuring Blocks - 08]'''<br>
	Group 006<br>		Group 006<br>
Line 116:		Line 116:
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>


	== Special Procedures ==		== Special Procedures ==

Peter: /* Brake Pressure Sensor 1 (G201) */

2015-05-08T15:41:55Z

Brake Pressure Sensor 1 (G201)

← Older revision		Revision as of 15:41, 8 May 2015
Line 84:		Line 84:
	After a successful basic setting, field 2 should say "OK".<br>		After a successful basic setting, field 2 should say "OK".<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	To make sure the basic setting was ~~succesful~~, check the sensor again.<br>		To make sure the basic setting was successful, check the sensor again.<br>
	'''[Measuring Blocks - 08]'''<br>		'''[Measuring Blocks - 08]'''<br>
	Group 005<br>		Group 005<br>
Line 91:		Line 91:
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>


	=== Longitudinal Acceleration Sensor (G251) ===		=== Longitudinal Acceleration Sensor (G251) ===

Peter: /* Lateral Acceleration Sensor (G200) */

2015-05-08T15:41:42Z

Lateral Acceleration Sensor (G200)

← Older revision		Revision as of 15:41, 8 May 2015
Line 59:		Line 59:
	After a successful basic setting, field 2 should say "OK".<br>		After a successful basic setting, field 2 should say "OK".<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	To make sure the basic setting was ~~succesful~~, check the sensor again.<br>		To make sure the basic setting was successful, check the sensor again.<br>
	'''[Measuring Blocks - 08]'''<br>		'''[Measuring Blocks - 08]'''<br>
	Group 004<br>		Group 004<br>
Line 66:		Line 66:
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>


	=== Brake Pressure Sensor 1 (G201) ===		=== Brake Pressure Sensor 1 (G201) ===

Peter: /* Sensor for Steering Angle (G85) */

2015-05-08T15:41:28Z

Sensor for Steering Angle (G85)

← Older revision		Revision as of 15:41, 8 May 2015
Line 29:		Line 29:
	After a successful basic setting, field 2 should say "OK".<br>		After a successful basic setting, field 2 should say "OK".<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	To make sure the basic setting was ~~succesful~~, check the sensor again.<br>		To make sure the basic setting was successful, check the sensor again.<br>
	'''[Measuring Blocks - 08]'''<br>		'''[Measuring Blocks - 08]'''<br>
	Group 004<br>		Group 004<br>
Line 36:		Line 36:
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>


	=== Lateral Acceleration Sensor (G200) ===		=== Lateral Acceleration Sensor (G200) ===

Andy: /* Coding */

2011-11-08T15:18:55Z

Coding

← Older revision		Revision as of 15:18, 8 November 2011
Line 3:		Line 3:
	== Coding ==		== Coding ==

	* '''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but ~~will~~ automatically be shown once you access the Coding Function using VCDS.''' ''If you are having trouble finding/calculating the proper Coding please Refer to the Factory Repair Manual or [http://ross-tech.com/contact.html Contact us directly].''		* '''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but may automatically be shown once you access the Coding Function using VCDS (provided the necessary label file with documentation is present).''' ''If you are having trouble finding/calculating the proper Coding please Refer to the Factory Repair Manual or [http://ross-tech.com/contact.html Contact us directly].''

	== Basic Setting ==		== Basic Setting ==

RtWiKiSyS0p at 19:42, 5 September 2011

2011-09-05T19:42:30Z

← Older revision		Revision as of 19:42, 5 September 2011
Line 3:		Line 3:
	== Coding ==		== Coding ==

	* '''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be shown once you access the Coding Function using VCDS.'''		* '''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be shown once you access the Coding Function using VCDS.''' ''If you are having trouble finding/calculating the proper Coding please Refer to the Factory Repair Manual or [http://ross-tech.com/contact.html Contact us directly].''

	== Basic Setting ==		== Basic Setting ==

RtWiKiSyS0p at 19:41, 5 September 2011

2011-09-05T19:41:21Z

← Older revision		Revision as of 19:41, 5 September 2011
Line 2:		Line 2:

	== Coding ==		== Coding ==
	~~=== Audi ===~~
	*No information at this time, email Ross Tech Support.

	~~=== Volkswagen ===~~		* '''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be shown once you access the Coding Function using VCDS.'''

	* ~~ABS = 03504~~
	* ABS/EDL = 13504
	* ABS/EDL/ASR = 13204

	== Basic Setting ==		== Basic Setting ==

Jef: /* Coding */

2011-06-16T17:37:01Z

Coding

← Older revision		Revision as of 17:37, 16 June 2011
Line 2:		Line 2:

	== Coding ==		== Coding ==
			=== Audi ===
			*No information at this time, email Ross Tech Support.

			=== Volkswagen ===

			* ABS = 03504
			* ABS/EDL = 13504
			* ABS/EDL/ASR = 13204

	== Basic Setting ==		== Basic Setting ==

RtWiKiSyS0p: Created page with 'FORCETOC == Coding == == Basic Setting == === Sensor for Steering Angle (G85) === '''Prerequisites:'''
* Start the vehicle. * Turn the steering wheel one turn …'

2010-11-15T16:41:33Z

Created page with '__FORCETOC__ == Coding == == Basic Setting == === Sensor for Steering Angle (G85) === '''Prerequisites:''' * Start the vehicle. * Turn the steering wheel one turn …'

New page

__FORCETOC__

== Coding ==

== Basic Setting ==
=== Sensor for Steering Angle (G85) ===

'''Prerequisites:''' 
* Start the vehicle.
* Turn the steering wheel one turn to the right and one turn to the left.
* Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.
* If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight.
* Ensure that the steering wheel is not moved again.
* Keep the engine running and do not switch off the ignition.
* System voltage at least 12.0 V. 

'''[Select]''' 
'''[03 - Brake Electronics]''' 
'''[Coding-II - 11]''' 
Enter 40168, to enable the basic setting. 
'''[Do it!]''' 
'''[Basic Settings - 04]''' 
Group 060 
'''[Go!]''' 
Activate the Basic Setting. 
'''[ON/OFF/Next]''' 
After a successful basic setting, field 2 should say "OK". 
'''[Done, Go Back]''' 
To make sure the basic setting was succesful, check the sensor again. 
'''[Measuring Blocks - 08]''' 
Group 004 
'''[Go!]''' 
Check field 1, the value has to be between -4.5 and +4.5 °. 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]''' 

=== Lateral Acceleration Sensor (G200) ===

'''Prerequisites:''' 
* System voltage at least 12.0 V. 

'''[Select]''' 
'''[03 - Brake Electronics]''' 
'''[Measuring Blocks - 08]''' 
Group 004 
'''[Go!]''' 
Check field 2, the value has to be between -1.5 and +1.5 m/s². 
'''[Done, Go Back]''' 
'''[Coding-II - 11]''' 
Enter 40168, to enable the basic setting. 
'''[Do it!]''' 
'''[Basic Settings - 04]''' 
Group 063 
'''[Go!]''' 
Activate the Basic Setting. 
'''[ON/OFF/Next]''' 
After a successful basic setting, field 2 should say "OK". 
'''[Done, Go Back]''' 
To make sure the basic setting was succesful, check the sensor again. 
'''[Measuring Blocks - 08]''' 
Group 004 
'''[Go!]''' 
Check field 2, the value has to be between -1.5 and +1.5 m/s². 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]''' 

=== Brake Pressure Sensor 1 (G201) ===

'''Prerequisites:''' 
* System voltage at least 12.0 V. 

'''[Select]''' 
'''[03 - Brake Electronics]''' 
'''[Coding-II - 11]''' 
Enter 40168, to enable the basic setting. 
'''[Do it!]''' 
'''[Basic Settings - 04]''' 
Group 066 
'''[Go!]''' 
Activate the Basic Setting. 
'''[ON/OFF/Next]''' 
After a successful basic setting, field 2 should say "OK". 
'''[Done, Go Back]''' 
To make sure the basic setting was succesful, check the sensor again. 
'''[Measuring Blocks - 08]''' 
Group 005 
'''[Go!]''' 
Check field 1, the value has to be between -7.0 and +7.0 bar. 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]''' 

=== Longitudinal Acceleration Sensor (G251) ===

'''Prerequisites:''' 
* System voltage at least 12.0 V. 

'''[Select]''' 
'''[03 - Brake Electronics]''' 
'''[Coding-II - 11]''' 
Enter 40168, to enable the basic setting. 
'''[Do it!]''' 
'''[Basic Settings - 04]''' 
Group 069 
'''[Go!]''' 
Activate the Basic Setting. 
'''[ON/OFF/Next]''' 
After a successful basic setting, field 2 should say "OK". 
'''[Done, Go Back]''' 
To make sure the basic setting was succesful, check the sensor again. 
'''[Measuring Blocks - 08]''' 
Group 006 
'''[Go!]''' 
Check field 1, the value has to be between -1.5 and +1.5 m/s². 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]''' 

== Special Procedures ==

=== System Function Test ===

See [[ESP System Function Test (Conti/Teves)|System Function Test]]

VW Golf (1J) Brake Electronics (MK20) - Revision history

Dana at 18:15, 16 August 2017

Peter: /* Longitudinal Acceleration Sensor (G251) */

Peter: /* Brake Pressure Sensor 1 (G201) */

Peter: /* Lateral Acceleration Sensor (G200) */

Peter: /* Sensor for Steering Angle (G85) */

Andy: /* Coding */

RtWiKiSyS0p at 19:42, 5 September 2011

RtWiKiSyS0p at 19:41, 5 September 2011

Jef: /* Coding */

RtWiKiSyS0p: Created page with '__FORCETOC__ == Coding == == Basic Setting == === Sensor for Steering Angle (G85) === '''Prerequisites:''' * Start the vehicle. * Turn the steering wheel one turn …'

RtWiKiSyS0p: Created page with 'FORCETOC == Coding == == Basic Setting == === Sensor for Steering Angle (G85) === '''Prerequisites:'''
* Start the vehicle. * Turn the steering wheel one turn …'