VW Golf (1K) Brake Electronics (MK60EC1) - Revision history

Dana at 18:19, 3 June 2022

2022-06-03T18:19:31Z

← Older revision		Revision as of 18:19, 3 June 2022
Line 145:		Line 145:
	* The pump temp must be below 27°C / 80°F. It may be necessary to use a fan with the hood open to keep the temp. down.		* The pump temp must be below 27°C / 80°F. It may be necessary to use a fan with the hood open to keep the temp. down.
	* The engine should be running due to the high brake fluid pressures required to complete the test.<br>		* The engine should be running due to the high brake fluid pressures required to complete the test.<br>
			* The brake system needs to be free of air. Make sure to bleed the system prior to beginning this process.<br>

	'''Note''': Both the [[#Basic Setting for Hydraulic Unit Intake Valves \| Basic Setting for Hydraulic Unit Intake Valves]] and [[#Basic Setting for Hydraulic Unit Disconnecting Valves \| Basic Setting for Hydraulic Unit Disconnecting Valves]] need to be performed in that order.		'''Note''': Both the [[#Basic Setting for Hydraulic Unit Intake Valves \| Basic Setting for Hydraulic Unit Intake Valves]] and [[#Basic Setting for Hydraulic Unit Disconnecting Valves \| Basic Setting for Hydraulic Unit Disconnecting Valves]] need to be performed in that order.

Dana at 19:13, 7 December 2020

2020-12-07T19:13:33Z

← Older revision		Revision as of 19:13, 7 December 2020
Line 210:		Line 210:
	* [[#Yaw Rate Sensor (G202)\|Basic Setting for Longitudinal Acceleration Sensor (G202)]]		* [[#Yaw Rate Sensor (G202)\|Basic Setting for Longitudinal Acceleration Sensor (G202)]]
	** The video located in our [https://forums.ross-tech.com/showthread.php?20619-MK60EC1-ABS-FAQ MK60EC1 ABS FAQ] covers the Coding and Basic Setting steps.		** The video located in our [https://forums.ross-tech.com/showthread.php?20619-MK60EC1-ABS-FAQ MK60EC1 ABS FAQ] covers the Coding and Basic Setting steps.


	If the (old) Hydraulics Unit is installed with a new or used ABS module these additional steps may need to be performed. This is '''only''' necessary when [[00003 \| 00003 - Control Module: No or Incorrect Basic Setting / Adaptation]] is present.		If the (old) Hydraulics Unit is installed with a new or used ABS module these additional steps may need to be performed. This is '''only''' necessary when [[00003 \| 00003 - Control Module: No or Incorrect Basic Setting / Adaptation]] is present.
Line 215:		Line 216:
	* [[#Intake Valves\|Basic Setting for Hydraulic Unit Intake Valves]]		* [[#Intake Valves\|Basic Setting for Hydraulic Unit Intake Valves]]
	* [[#Disconnecting Valves\|Basic Setting for Hydraulic Unit Disconnecting Valves]]		* [[#Disconnecting Valves\|Basic Setting for Hydraulic Unit Disconnecting Valves]]


			If DTC [[01486 \| 01486 - System Function Test activated]] is stored:
			* The [[ESP System Function Test]] drive can be completed after ALL of the replacement steps are complete. [[01486]] cannot be resolved unless it is the only DTC stored.

Dana at 16:54, 7 February 2020

2020-02-07T16:54:11Z

← Older revision		Revision as of 16:54, 7 February 2020
Line 209:		Line 209:
	* [[#Brake Pressure Sensor 1 (G201)\|Basic Setting for Brake Pressure Sensor 1 (G201)]]		* [[#Brake Pressure Sensor 1 (G201)\|Basic Setting for Brake Pressure Sensor 1 (G201)]]
	* [[#Yaw Rate Sensor (G202)\|Basic Setting for Longitudinal Acceleration Sensor (G202)]]		* [[#Yaw Rate Sensor (G202)\|Basic Setting for Longitudinal Acceleration Sensor (G202)]]
			** The video located in our [https://forums.ross-tech.com/showthread.php?20619-MK60EC1-ABS-FAQ MK60EC1 ABS FAQ] covers the Coding and Basic Setting steps.

	If the (old) Hydraulics Unit is installed with a new or used ABS module these additional steps may need to be performed. This is '''only''' necessary when [[00003 \| 00003 - Control Module: No or Incorrect Basic Setting / Adaptation]] is present.		If the (old) Hydraulics Unit is installed with a new or used ABS module these additional steps may need to be performed. This is '''only''' necessary when [[00003 \| 00003 - Control Module: No or Incorrect Basic Setting / Adaptation]] is present.

Jef: /* Video Link */

2016-10-21T20:03:12Z

Video Link

← Older revision		Revision as of 20:03, 21 October 2016
Line 192:		Line 192:

	=== Video Link ===		=== Video Link ===
	[[File:~~025~~-~~026_thumb~~.jpg\|200px\|link=~~http~~://www.youtube.com/watch?v=~~u8s1dwW9HwY~~]]		[[File:ABS_025_-_026_thumb.jpg\|200px\|link=https://www.youtube.com/watch?v=b6lm9OmC2so]]

			https://www.youtube.com/watch?v=b6lm9OmC2so

	~~http://www.youtube.com/watch?v=u8s1dwW9HwY~~

Dana: /* Coding */

2016-08-30T18:48:38Z

Coding

← Older revision		Revision as of 18:48, 30 August 2016
Line 1:		Line 1:
	== Coding ==		== Coding ==

	'''Coding for this Control Module is normally done via Software Version Management (SVM). If the old Control Module is still accessible read/copy it~~'s Coding to~~ the ~~new~~ Module.'''		'''Coding for this Control Module is normally done via Software Version Management (SVM). If the old Control Module is still accessible read/copy its Coding and Paste it into the New coding line of the replacement Module.'''
	* If the old control module will not communicate, or the original coding was not saved prior to repairs, registered customers can [mailto:Support@Ross-Tech.com contact us directly via email] for assistance. Please send the complete [http://www.ross-tech.com/vcds/tour/autoscan.html Auto-Scan] with the recent repair history and we can try to help with the Coding Process.<br> <br>		* If the old control module will not communicate, or the original coding was not saved prior to repairs, registered customers can [mailto:Support@Ross-Tech.com contact us directly via email] for assistance. Please send the complete [http://www.ross-tech.com/vcds/tour/autoscan.html Auto-Scan] with the recent repair history and we can try to help with the Coding Process.
			* It is strongly recommended to complete the Sensor for Steering Angle (G85) Basic Setting operation immediately after coding the control module.<br> <br>

	== Security Access ==		== Security Access ==

Dana: /* Longitudinal Acceleration Sensor (G251) */

2016-02-11T14:33:25Z

Longitudinal Acceleration Sensor (G251)

← Older revision		Revision as of 14:33, 11 February 2016
Line 106:		Line 106:
	=== Longitudinal Acceleration Sensor (G251) ===		=== Longitudinal Acceleration Sensor (G251) ===

			'''<u>Note:</u>'''<br>
			* The Longitudinal Acceleration Sensor (G251) is only present cars with All Wheel Drive (AWD) and/or Hill Hold Control (HHC)<br>
	'''<u>Prerequisites:</u>'''<br>		'''<u>Prerequisites:</u>'''<br>
	* System voltage at least 12.0 V.<br>		* System voltage at least 12.0 V.<br>
Line 134:		Line 136:

	----		----


	=== Basic Setting for Hydraulic Unit Intake Valves ===		=== Basic Setting for Hydraulic Unit Intake Valves ===

Dana at 17:20, 8 December 2015

2015-12-08T17:20:33Z

← Older revision		Revision as of 17:20, 8 December 2015
Line 207:		Line 207:
	* [[#Yaw Rate Sensor (G202)\|Basic Setting for Longitudinal Acceleration Sensor (G202)]]		* [[#Yaw Rate Sensor (G202)\|Basic Setting for Longitudinal Acceleration Sensor (G202)]]

	If the (old) Hydraulics Unit is ~~still~~ installed these ~~Steps~~ may ~~have~~ to be performed ~~as well~~:		If the (old) Hydraulics Unit is installed with a new or used ABS module these additional steps may need to be performed. This is '''only''' necessary when [[00003 \| 00003 - Control Module: No or Incorrect Basic Setting / Adaptation]] is present.

	* [[#Intake Valves\|Basic Setting for Hydraulic Unit Intake Valves]]		* [[#Intake Valves\|Basic Setting for Hydraulic Unit Intake Valves]]
	* [[#Disconnecting Valves\|Basic Setting for Hydraulic Unit Disconnecting Valves]]		* [[#Disconnecting Valves\|Basic Setting for Hydraulic Unit Disconnecting Valves]]

Dana at 14:25, 6 October 2015

2015-10-06T14:25:53Z

← Older revision		Revision as of 14:25, 6 October 2015
Line 2:		Line 2:

	'''Coding for this Control Module is normally done via Software Version Management (SVM). If the old Control Module is still accessible read/copy it's Coding to the new Module.'''		'''Coding for this Control Module is normally done via Software Version Management (SVM). If the old Control Module is still accessible read/copy it's Coding to the new Module.'''
	* If the old control module will not communicate, or the original coding was not saved prior to repairs, registered customers can [mailto:Support@Ross-Tech.com contact us directly via email] for assistance. Please send the complete Auto-Scan with the recent repair history and we can try to help with the Coding Process.<br> <br>		* If the old control module will not communicate, or the original coding was not saved prior to repairs, registered customers can [mailto:Support@Ross-Tech.com contact us directly via email] for assistance. Please send the complete [http://www.ross-tech.com/vcds/tour/autoscan.html Auto-Scan] with the recent repair history and we can try to help with the Coding Process.<br> <br>

	== Security Access ==		== Security Access ==

Dana: /* Sensor for Steering Angle (G85) */

2015-02-12T16:40:15Z

Sensor for Steering Angle (G85)

← Older revision		Revision as of 16:40, 12 February 2015
Line 38:		Line 38:
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>

	'''''Note:''' After successful basic setting, the [[VW_Golf_(1K)_Steering_Assist#Steering_Limit_Stop_Adaptation\|Steering Limit Stop]] needs to be adapted too.''<br>		'''''Note:'''
			* If Adjustment Not Possible is displayed:
			** The On/Off/Next button was used and the procedure will need to be repeated WITHOUT clicking it.
			** The G85 live values were not within the +/-1.5 °specification. Repeating the procedure within specifications should resolve it.
			** The Steering wheel should be turned to full right lock stop and to full left lock stop and centered again followed by repeating the procedure.
			** The 16-Steerign Wheel control module and 44-Steering Assist control module (when applicable) Coding and Adaptation configurations should be checked to rule out a conflict.
			* After successful basic setting, the [[VW_Golf_(1K)_Steering_Assist#Steering_Limit_Stop_Adaptation\|Steering Limit Stop]] needs to be adapted too.''<br>

	=== Lateral Acceleration Sensor (G200) ===		=== Lateral Acceleration Sensor (G200) ===

Dana at 20:20, 10 September 2013

2013-09-10T20:20:39Z

← Older revision		Revision as of 20:20, 10 September 2013
Line 1:		Line 1:
	== Coding ==		== Coding ==

	'''Coding for this Control Module is normally done via Software Version Management (SVM). If the old Control Module is still accessible read/copy it's Coding to the new Module. ~~In case this is~~ not ~~possible please~~ [~~http~~:~~//www.ross~~-~~tech~~.com~~/contact.html~~ contact us directly] ~~and we will assist you with the Coding Process~~.		'''Coding for this Control Module is normally done via Software Version Management (SVM). If the old Control Module is still accessible read/copy it's Coding to the new Module.'''
			* If the old control module will not communicate, or the original coding was not saved prior to repairs, registered customers can [mailto:Support@Ross-Tech.com contact us directly via email] for assistance. Please send the complete Auto-Scan with the recent repair history and we can try to help with the Coding Process.<br> <br>
	~~''Every inquiry on this topic has to include a full Auto-Scan as well as which parts have been replaced and why, also make sure~~ the Auto-Scan ~~includes~~ the ~~complete VIN of~~ the ~~vehicle in question~~.''<br> <br>

	== Security Access ==		== Security Access ==

← Older revision		Revision as of 16:54, 7 February 2020
Line 209:		Line 209:
	* [[#Brake Pressure Sensor 1 (G201)\|Basic Setting for Brake Pressure Sensor 1 (G201)]]		* [[#Brake Pressure Sensor 1 (G201)\|Basic Setting for Brake Pressure Sensor 1 (G201)]]
	* [[#Yaw Rate Sensor (G202)\|Basic Setting for Longitudinal Acceleration Sensor (G202)]]		* [[#Yaw Rate Sensor (G202)\|Basic Setting for Longitudinal Acceleration Sensor (G202)]]
			** The video located in our [https://forums.ross-tech.com/showthread.php?20619-MK60EC1-ABS-FAQ MK60EC1 ABS FAQ] covers the Coding and Basic Setting steps.

	If the (old) Hydraulics Unit is installed with a new or used ABS module these additional steps may need to be performed. This is '''only''' necessary when [[00003 \| 00003 - Control Module: No or Incorrect Basic Setting / Adaptation]] is present.		If the (old) Hydraulics Unit is installed with a new or used ABS module these additional steps may need to be performed. This is '''only''' necessary when [[00003 \| 00003 - Control Module: No or Incorrect Basic Setting / Adaptation]] is present.

← Older revision		Revision as of 17:20, 8 December 2015
Line 207:		Line 207:
	* [[#Yaw Rate Sensor (G202)\|Basic Setting for Longitudinal Acceleration Sensor (G202)]]		* [[#Yaw Rate Sensor (G202)\|Basic Setting for Longitudinal Acceleration Sensor (G202)]]

	If the (old) Hydraulics Unit is ~~still~~ installed these ~~Steps~~ may ~~have~~ to be performed ~~as well~~:		If the (old) Hydraulics Unit is installed with a new or used ABS module these additional steps may need to be performed. This is '''only''' necessary when [[00003 \| 00003 - Control Module: No or Incorrect Basic Setting / Adaptation]] is present.

	* [[#Intake Valves\|Basic Setting for Hydraulic Unit Intake Valves]]		* [[#Intake Valves\|Basic Setting for Hydraulic Unit Intake Valves]]
	* [[#Disconnecting Valves\|Basic Setting for Hydraulic Unit Disconnecting Valves]]		* [[#Disconnecting Valves\|Basic Setting for Hydraulic Unit Disconnecting Valves]]