VW Golf (1K) Comfort System - Revision history

Dana at 16:18, 16 May 2013

2013-05-16T16:18:12Z

← Older revision		Revision as of 16:18, 16 May 2013
Line 134:		Line 134:

	''''If the remotes will not match and the module is not confirming during the Adaptation process check the following possible causes:'''		''''If the remotes will not match and the module is not confirming during the Adaptation process check the following possible causes:'''
			* Incorrect remote(s)
	* Incorrect Coding		* Incorrect Coding
	* Factory Mode enabled in new module		* Factory Mode enabled in new module
	* Incorrect remote(s)		* Incorrect control module
	* Incorrect Central Electronics module		* Old remote control positions aren't cleared. Use the [[VW Golf (1K) Comfort System#Adaptation\|Remote Control Clearing]] procedure as needed.


	''Registered customers can [mailto:Support@Ross-Tech.com contact us directly via email] for assistance. Every inquiry on this topic must include a full Auto-Scan as well as which parts have been replaced and why.''		''Registered customers can [mailto:Support@Ross-Tech.com contact us directly via email] for assistance. Every inquiry on this topic must include a full Auto-Scan as well as which parts have been replaced and why.''

Dana at 16:59, 26 September 2012

2012-09-26T16:59:11Z

@@ Line 112: / Line 112: @@
 * Make sure all vehicle remotes are present.
 * Run and save a complete Auto-Scan and save it prior to module removal. See the [http://www.ross-tech.com/vcds/tour/autoscan.html  Online Manual Auto-Scan].<br>
-* Code the module with the Long Coding from the original module found in t
+* Code the module with the Long Coding from the original module found in the Auto-Scan.<br>

Dana at 16:57, 26 September 2012

2012-09-26T16:57:20Z

← Older revision		Revision as of 16:57, 26 September 2012
Line 1:		Line 1:
	== Coding ==		== Coding ==

	''Coding information is found using the Long Coding Helper while connected to the vehicle with VCDS.''		* Coding information is found using the '''[http://www.ross-tech.com/vcds/tour/recode_screen.html Long Coding Helper]''' while connected to the vehicle with VCDS.
			* When replacing a module it is critical to save the original coding and transfer it to the new module as explained in the Replacement section below.<br>


			----

	== Adaptation ==		== Adaptation ==
Line 90:		Line 93:
	Factory Mode is usually active when a newly delivered Control Module is being installed. To enable all Functions of the new Control Module Factory Mode has to be disabled. Once it has been disabled it cannot be enabled again.		Factory Mode is usually active when a newly delivered Control Module is being installed. To enable all Functions of the new Control Module Factory Mode has to be disabled. Once it has been disabled it cannot be enabled again.


			----

	== Special Procedures ==		== Special Procedures ==
Line 99:		Line 104:
	* Press the remote control ''lock'' or ''unlock'' button.		* Press the remote control ''lock'' or ''unlock'' button.
	''The synchronization is now finished.''		''The synchronization is now finished.''


			----

			== Replacement ==

			* Make sure all vehicle remotes are present.
			* Run and save a complete Auto-Scan and save it prior to module removal. See the [http://www.ross-tech.com/vcds/tour/autoscan.html Online Manual Auto-Scan].<br>
			* Code the module with the Long Coding from the original module found in t

Dana: /* Channel 001: Remote Control Matching */

2012-06-12T22:00:49Z

Channel 001: Remote Control Matching

← Older revision		Revision as of 22:00, 12 June 2012
Line 14:		Line 14:
	* Press and hold the '''Unlock''' button for at least one second on each Remote Control you want to add, the Blinkers will light up to confirm the Adaptation Process of each Remote Control.		* Press and hold the '''Unlock''' button for at least one second on each Remote Control you want to add, the Blinkers will light up to confirm the Adaptation Process of each Remote Control.

	'''''~~Note~~:''' The time for matching remotes after saving the new value should not exceed 15 seconds. You can add a maximum of 4 remotes. '''Remote Control for Cars equipped with Keyless Entry and Access are automatically being matched when [[VW Passat (3C) Immobilizer\|Adapting the Immobilizer/Keys]].~~'''''~~		'''''Notes:'''
			* The time for matching remotes after saving the new value should not exceed '''15 seconds'''. You can add a maximum of '''4 remotes'''.
			* If the '''[Test]''' and/or '''[Save]''' buttons are gray and not clickable the module likely has all 4 positions filled and clearing remotes will be necessary in Channel 000.
			* Remote Control for Cars equipped with Keyless Entry and Access are automatically being matched when [[VW Passat (3C) Immobilizer\|Adapting the Immobilizer/Keys]].

	=== Channel 003: Selective (Single) Door Locking ===		=== Channel 003: Selective (Single) Door Locking ===

Andy: /* Channel 001: Remote Control Matching */

2011-06-02T18:59:42Z

Channel 001: Remote Control Matching

← Older revision		Revision as of 18:59, 2 June 2011
Line 12:		Line 12:

	* Start Matching new/additional Remote Controls with entering '''1''', then '''Test''' and '''Save''' the New Value.		* Start Matching new/additional Remote Controls with entering '''1''', then '''Test''' and '''Save''' the New Value.
	* Press the '''Unlock''' button on each Remote Control you want to add, the Blinkers will light up to confirm the Adaptation Process of each Remote Control.		* Press and hold the '''Unlock''' button for at least one second on each Remote Control you want to add, the Blinkers will light up to confirm the Adaptation Process of each Remote Control.

	'''''Note:''' The time for matching remotes after saving the new value should not exceed 15 seconds. You can add a maximum of 4 remotes. '''Remote Control for Cars equipped with Keyless Entry and Access are automatically being matched when [[VW Passat (3C) Immobilizer\|Adapting the Immobilizer/Keys]].'''''		'''''Note:''' The time for matching remotes after saving the new value should not exceed 15 seconds. You can add a maximum of 4 remotes. '''Remote Control for Cars equipped with Keyless Entry and Access are automatically being matched when [[VW Passat (3C) Immobilizer\|Adapting the Immobilizer/Keys]].'''''

RtWiKiSyS0p at 19:50, 15 March 2011

2011-03-15T19:50:00Z

← Older revision		Revision as of 19:50, 15 March 2011
Line 1:		Line 1:
	== Coding ==		== Coding ==

			''Coding information is found using the Long Coding Helper while connected to the vehicle with VCDS.''


	== Adaptation ==		== Adaptation ==
	=== Channel 000: Remote Control Clearing ===		=== Channel 000: Remote Control Clearing ===

	'''~~[Select]~~'''~~<br>~~		* This Adaptation Channel is used to clear all matched Remote Controls.
	'''~~[46 - Central Conv.]~~'''~~<br>~~
	'''~~[Adaptation - 10]~~'''~~<br>~~		=== Channel 001: Remote Control Matching ===
	~~Channel 000~~.~~<br>~~
	'''~~[Read]~~'''~~<br>~~		* Start Matching new/additional Remote Controls with entering '''1''', then '''Test''' and '''Save''' the New Value.
	~~To clear all matched remote controls press save.<br>~~		* Press the '''Unlock''' button on each Remote Control you want to add, the Blinkers will light up to confirm the Adaptation Process of each Remote Control.
	'''~~[Save]~~'''~~<br>~~
	'''[~~Done, Go Back~~]'''~~<br>~~		'''''Note:''' The time for matching remotes after saving the new value should not exceed 15 seconds. You can add a maximum of 4 remotes. '''Remote Control for Cars equipped with Keyless Entry and Access are automatically being matched when [[VW Passat (3C) Immobilizer\|Adapting the Immobilizer/Keys]].'''''
	''~~'[Close Controller, Go Back~~ - ~~06]'''<br>~~
			=== Channel 003: Selective (Single) Door Locking ===
			* 0 = Selective Door Locking OFF
			* 1 = Selective Door Locking ON

			=== Channel 004: Auto-Lock ===
			The Doors will lock automatically when the Vehicle reaches a Speed of 15 km/h or 10 mph.
			* 0 = Auto-Lock OFF
			* 1 = Auto-Lock ON

			=== Channel 005: Auto-Unlock ===
			The Doors will unlock automatically when the Key is removed from the Ignition Switch.
			* 0 = Auto-Unlock OFF
			* 1 = Auto-Unlock ON

			=== Channel 007: Unlocking Confirmation (Remote Control) ===
			Type of Confirmation when unlocking the Car via Remote Control.
			* 0 = Confirmation OFF
			* 1 = Confirmation via Blinker/Turn Signal
			* 2 = Confirmation via Beep/Horn
			* 3 = Confirmation via Beep/Horn & Blinker/Turn Signal

	=== Channel ~~001~~: Remote Control ~~Matching~~ ===		=== Channel 008: Unlocking Confirmation (Key Switch) ===
			Type of Confirmation when unlocking the Car via Key/Lock Switch.
			* 0 = Confirmation OFF
			* 1 = Confirmation via Blinker/Turn Signal
			* 2 = Confirmation via Beep/Horn
			* 3 = Confirmation via Beep/Horn & Blinker/Turn Signal

			=== Channel 010: Locking Confirmation (Remote Control) ===
			Type of Confirmation when locking the Car via Remote Control.
			* 0 = Confirmation OFF
			* 1 = Confirmation via Blinker/Turn Signal
			* 2 = Confirmation via Beep/Horn
			* 3 = Confirmation via Beep/Horn & Blinker/Turn Signal

			=== Channel 011: Locking Confirmation (Key Switch) ===
			Type of Confirmation when locking the Car via Key/Lock Switch.
			* 0 = Confirmation OFF
			* 1 = Confirmation via Blinker/Turn Signal
			* 2 = Confirmation via Beep/Horn
			* 3 = Confirmation via Beep/Horn & Blinker/Turn Signal

			=== Channel 012: Safe Confirmation ===
			Type of Confirmation when the car is being locked.
			* 0 = Confirmation OFF
			* 1 = Confirmation via Blinker/Turn Signal
			* 2 = Confirmation via Beep/Horn
			* 3 = Confirmation via Beep/Horn & Blinker/Turn Signal

	~~'''[Select]'''<br>~~		=== Channel 013: Alarm Horn Adjustment ===
	~~'''[46 - Central Conv]'''<br>~~		The Alarm Horn Country Setting changes the Length and Volume of the Alarm Horn Sound.
	~~'''[Adaptation - 10]'''<br>~~		* 0 = Great Britain (Frequency Modulated - 10 Tamper Alarms)
	Channel ~~001.<br>~~		* 1 = Great Britain (Frequency Modulated - 1 Tamper Alarm)
	~~'''[Read]'''<br><br>~~		* 2 = Rest of World (Discontinuous - 10 Tamper Alarms)
	~~''<u>Note:</u>~~ The ~~value does NOT show~~ the ~~actual number~~ of ~~adapted remotes~~.''		* 3 = Rest of World (Discontinuous - 1 Tamper Alarm)
	* 0 = ~~All memory positions occupied, matching~~ of ~~additionals keys not possible, clear memory positons first.<br>~~
	* 1 = ~~Matching~~ of ~~additional remotes possible.~~

			=== Channel 017: Comfort Function ===
			Enables Comfort via Remote Functionality depending on the Options enabled in the Control Module Coding. ''This Adaptation Channel will have no Effect if the Comfort Function(s) are disabled in the Control Module Coding.''

	* ~~Start matching new/additional remotes with entering "~~1~~" as new value.~~		* 0 = Comfort Function OFF
			* 1 = Comfort Function ON

	~~'''[Test]'''<br>~~		=== Channel 018: Alarm Delay ===
	~~'''[Save]'''<br><br>~~		Deactivates the Anti-Theft-Warning Delay when opening the Drivers Door before the Anti-Theft-Warning-System is being activated.
	~~''<u>Note~~:~~</u> The time for matching remotes after saving the new value should not exceed 30 seconds. You can add a maximum of 4 remotes.''<br>~~
	* Press the ~~''unlock'' button on each remote control you want to add,~~ the ~~blinkers will light up to confirm~~ the ~~adaptation process of each remote~~.

	~~'''[Done, Go Back]'''<br>~~		* 0 = Alarm Delay OFF
	~~'''[Close Controller, Go Back - 06]'''<br>~~		* 1 = Alarm Delay ON

			=== Channel 019: Factory Mode ===
			Factory Mode is usually active when a newly delivered Control Module is being installed. To enable all Functions of the new Control Module Factory Mode has to be disabled. Once it has been disabled it cannot be enabled again.


	== Special Procedures ==		== Special Procedures ==
	=== Remote Control ~~Synchronisation~~ ===		=== Remote Control Synchronization ===
	* If locked, open the car using the drivers door lock.		* If locked, open the car using the drivers door lock.
	* Press the remote control ''unlock'' button.		* Press the remote control ''unlock'' button.
Line 45:		Line 95:
	* Switch off ignition and pull the key out of the ignition lock.		* Switch off ignition and pull the key out of the ignition lock.
	* Press the remote control ''lock'' or ''unlock'' button.		* Press the remote control ''lock'' or ''unlock'' button.
	''The ~~synchronisation~~ is now finished.''		''The synchronization is now finished.''

Uwe at 02:45, 21 January 2010

2010-01-21T02:45:01Z

← Older revision		Revision as of 02:45, 21 January 2010
Line 4:		Line 4:

	'''[Select]'''<br>		'''[Select]'''<br>
	'''[46 - ~~Comfort System~~]'''<br>		'''[46 - Central Conv.]'''<br>
	'''[Adaptation - 10]'''<br>		'''[Adaptation - 10]'''<br>
	Channel 000.<br>		Channel 000.<br>
Line 17:		Line 17:

	'''[Select]'''<br>		'''[Select]'''<br>
	'''[46 - ~~Comfort System~~]'''<br>		'''[46 - Central Conv]'''<br>
	'''[Adaptation - 10]'''<br>		'''[Adaptation - 10]'''<br>
	Channel 001.<br>		Channel 001.<br>

RtWiKiSyS0p at 12:49, 4 April 2006

2006-04-04T12:49:26Z

← Older revision		Revision as of 12:49, 4 April 2006
Line 30:		Line 30:
	'''[Test]'''<br>		'''[Test]'''<br>
	'''[Save]'''<br><br>		'''[Save]'''<br><br>
	''<u>Note:</u> The time for matching remotes after saving the new value should not exceed 30 seconds.''		''<u>Note:</u> The time for matching remotes after saving the new value should not exceed 30 seconds. You can add a maximum of 4 remotes.''<br>
	* Press the ''unlock'' button on each remote control you want to add, the blinkers will light up to confirm the adaptation process of each remote.		* Press the ''unlock'' button on each remote control you want to add, the blinkers will light up to confirm the adaptation process of each remote.

RtWiKiSyS0p at 12:41, 4 April 2006

2006-04-04T12:41:05Z

New page

== Coding ==
== Adaptation ==
=== Channel 000: Remote Control Clearing ===

'''[Select]''' 
'''[46 - Comfort System]''' 
'''[Adaptation - 10]''' 
Channel 000. 
'''[Read]''' 
To clear all matched remote controls press save. 
'''[Save]''' 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]''' 

=== Channel 001: Remote Control Matching ===

'''[Select]''' 
'''[46 - Comfort System]''' 
'''[Adaptation - 10]''' 
Channel 001. 
'''[Read]''' 
''Note: The value does NOT show the actual number of adapted remotes.''
* 0 = All memory positions occupied, matching of additionals keys not possible, clear memory positons first. 
* 1 = Matching of additional remotes possible.

* Start matching new/additional remotes with entering "1" as new value.

'''[Test]''' 
'''[Save]''' 
''Note: The time for matching remotes after saving the new value should not exceed 30 seconds.''
* Press the ''unlock'' button on each remote control you want to add, the blinkers will light up to confirm the adaptation process of each remote.

'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]''' 

== Special Procedures ==
=== Remote Control Synchronisation ===
* If locked, open the car using the drivers door lock.
* Press the remote control ''unlock'' button.
* Put the key in the ignition lock and switch on ignition.
* Switch off ignition and pull the key out of the ignition lock.
* Press the remote control ''lock'' or ''unlock'' button.
''The synchronisation is now finished.''