VW Golf (5K) AirbagVW10 - Revision history

Jef: /* Seat Occupied Recognition Control Module (J706): Reset */

2023-04-05T19:39:02Z

Seat Occupied Recognition Control Module (J706): Reset

← Older revision		Revision as of 19:39, 5 April 2023
Line 75:		Line 75:
	<br>		<br>
	'''Notes'''		'''Notes'''
	* If you get a "Request Sequence Error" when performing the ~~above procedures using VCDS Release 17.8 please update to~~ the ~~current Release~~: ~~http://www.ross~~-~~tech.com/vcds/download/current~~.~~php~~		* If you get a "Request Sequence Error" when performing the '''Resetting seat occupied recognition''' then check the following Advance Measuring Values:
			** IDE03871-ENG99733,Seat occupied recognition real part-Measured Value Capacitance
			** IDE03872-ENG99733,Seat occupied recognition imaginary part-Measured Value Capacitance
			** IDE03873-ENG99733,Seat occupied recognition compensated imaginary part-Measured Value Capacitance
			*** Not all systems have location IDE03873-ENG99733
			It can be normal for one of those locations to be a value of 0 pF, but if two of those locations are 0 pF, it may be a sign of a failed pressure mat that needs to be replaced.
	* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.		* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.

Dana at 22:42, 8 February 2018

2018-02-08T22:42:08Z

← Older revision		Revision as of 22:42, 8 February 2018
Line 75:		Line 75:
	<br>		<br>
	'''Notes'''		'''Notes'''
	* If you get a "Request Sequence Error" when performing the above procedures using VCDS Release 17.8 please ~~try Beta 17.10~~: http://www.ross-tech.com/vcds/download~~/beta~~/current.php		* If you get a "Request Sequence Error" when performing the above procedures using VCDS Release 17.8 please update to the current Release: http://www.ross-tech.com/vcds/download/current.php
	* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.		* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.

Dana at 13:14, 30 October 2017

2017-10-30T13:14:37Z

← Older revision		Revision as of 13:14, 30 October 2017
Line 75:		Line 75:
	<br>		<br>
	'''Notes'''		'''Notes'''
	* If you get a "Request Sequence Error" when performing the above procedures~~, try '''[Coding - 07]''' the '''[15 - Airbags]''' module with the same Coding value it already has. It may give you an error but proceed anyway with the two Basic Settings steps shown above.~~		* If you get a "Request Sequence Error" when performing the above procedures using VCDS Release 17.8 please try Beta 17.10: http://www.ross-tech.com/vcds/download/beta/current.php
	** '''If you encounter difficulty using VCDS Release 17.8 please ~~email the complete Auto-Scan to [mailto~~:~~Support@Ross~~-~~Tech~~.com ~~Support]'''~~
	* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.		* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.

Dana at 16:02, 22 September 2017

2017-09-22T16:02:39Z

← Older revision		Revision as of 16:02, 22 September 2017
Line 1:		Line 1:
	__FORCETOC__		__FORCETOC__

			This Airbag system can be identified by evaluating the data in the Auto-Scan:
			Address 15: Airbags (J234) Labels:\| 5K0-959-655.clb
			Part No SW: 5C0 959 655 B HW: 5C0 959 655 B
			Component: '''AirbagVW10''' 013 0613
			ASAM Dataset: EV_'''AirbaVW10'''SMEVW360 A01014

			Address 15: Airbags (J234) Labels:\| 5K0-959-655.clb
			Part No SW: 5C0 959 655 Q HW: 5C0 959 655 Q
			Component: '''AirbagVW10G''' 014 0851
			ASAM Dataset: EV_'''AirbaVW10'''SMEVW360 001026


	== Coding ==		== Coding ==

Dana: /* Seat Occupied Recognition Control Module (J706): Reset */

2017-08-17T18:22:10Z

Seat Occupied Recognition Control Module (J706): Reset

← Older revision		Revision as of 18:22, 17 August 2017
Line 64:		Line 64:
	'''Notes'''		'''Notes'''
	* If you get a "Request Sequence Error" when performing the above procedures, try '''[Coding - 07]''' the '''[15 - Airbags]''' module with the same Coding value it already has. It may give you an error but proceed anyway with the two Basic Settings steps shown above.		* If you get a "Request Sequence Error" when performing the above procedures, try '''[Coding - 07]''' the '''[15 - Airbags]''' module with the same Coding value it already has. It may give you an error but proceed anyway with the two Basic Settings steps shown above.
			** '''If you encounter difficulty using VCDS Release 17.8 please email the complete Auto-Scan to [mailto:Support@Ross-Tech.com Support]'''
	* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.		* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.


	== Special Notes ==		== Special Notes ==

Dana at 13:45, 11 May 2017

2017-05-11T13:45:07Z

← Older revision		Revision as of 13:45, 11 May 2017
Line 62:		Line 62:
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>
	<br>		<br>
	'''~~Note~~''' If you get a "Request Sequence Error" when performing the above procedures, try '''[Coding - 07]''' the '''[15 - Airbags]''' module with the same Coding value it already has. It may give you an error but proceed anyway with the two Basic Settings steps shown above.		'''Notes'''
			* If you get a "Request Sequence Error" when performing the above procedures, try '''[Coding - 07]''' the '''[15 - Airbags]''' module with the same Coding value it already has. It may give you an error but proceed anyway with the two Basic Settings steps shown above.
			* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.

Dana at 14:07, 2 February 2016

2016-02-02T14:07:51Z

← Older revision		Revision as of 14:07, 2 February 2016
Line 28:		Line 28:
	'''[Do it!]'''<br>		'''[Do it!]'''<br>
	'''[Basic Settings - 04]'''<br>		'''[Basic Settings - 04]'''<br>
	~~'' When applicable type the single digit 0 into the (reserved ) box. If this is not present skip this step.''<br>~~
	Select '''Seat occupied recognition serial number'''.<br>		Select '''Seat occupied recognition serial number'''.<br>
			'' When applicable type the single digit 0 into the (reserved) box. If this is not present skip this step.''<br>
	'''[Go!]''' to activate the Basic Setting.<br>		'''[Go!]''' to activate the Basic Setting.<br>
	After the result of '''Finished Correctly''' appears click '''[Stop]'''<br>		After the result of '''Finished Correctly''' appears click '''[Stop]'''<br>
Line 53:		Line 53:
	'''[Do it!]'''<br>		'''[Do it!]'''<br>
	'''[Basic Settings - 04]'''<br>		'''[Basic Settings - 04]'''<br>
	~~'' When applicable type the single digit 0 into the (reserved ) box. If this is not present skip this step.''<br>~~
	Select '''Resetting seat occupied recognition'''.<br>		Select '''Resetting seat occupied recognition'''.<br>
			'' When applicable type the single digit 0 into the (reserved) box. If this is not present skip this step.''<br>
	'''[Go!]''' to activate the Basic Setting.<br>		'''[Go!]''' to activate the Basic Setting.<br>
	After the result of '''Finished Correctly''' appears click '''[Stop]'''<br>		After the result of '''Finished Correctly''' appears click '''[Stop]'''<br>

Andy at 13:57, 10 February 2015

2015-02-10T13:57:20Z

← Older revision		Revision as of 13:57, 10 February 2015
Line 61:		Line 61:
	'''[Fault Codes - 02]''' ''Faults should NOT be stored''<br>		'''[Fault Codes - 02]''' ''Faults should NOT be stored''<br>
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>
			<br>
			'''Note''' If you get a "Request Sequence Error" when performing the above procedures, try '''[Coding - 07]''' the '''[15 - Airbags]''' module with the same Coding value it already has. It may give you an error but proceed anyway with the two Basic Settings steps shown above.

Dana: /* Special Notes */

2013-12-17T18:20:25Z

Special Notes

← Older revision		Revision as of 18:20, 17 December 2013
Line 64:		Line 64:

	== Special Notes ==		== Special Notes ==
	Due to liability concerns, Ross Tech does not offer assistance for installing used airbag components.		'''Due to liability concerns, Ross Tech does not offer assistance for installing used airbag components. '''
	* If you click the basic settings tests out of sequence, you may need to exit the module, cycle the key and repeat the entire process.		* If you click the basic settings tests out of sequence, you may need to exit the module, cycle the key and repeat the entire process.
	* If the procedure results in an error message -or- does not complete as expected:		* If the procedure results in an error message -or- does not complete as expected:

Dana at 18:19, 17 December 2013

2013-12-17T18:19:43Z

← Older revision		Revision as of 18:19, 17 December 2013
Line 64:		Line 64:

	== Special Notes ==		== Special Notes ==
			Due to liability concerns, Ross Tech does not offer assistance for installing used airbag components.
	* If you click the basic settings tests out of sequence, you may need to exit the module, cycle the key and repeat the entire process.		* If you click the basic settings tests out of sequence, you may need to exit the module, cycle the key and repeat the entire process.
	* If the procedure results in an error message ~~of any type~~ or does not complete as expected:		* If the procedure results in an error message -or- does not complete as expected:
	# Registered users can send a complete Auto-Scan via [mailto:Support@Ross-Tech.com email].		# Registered users can send a complete Auto-Scan via [mailto:Support@Ross-Tech.com email].
	# Include specific details regarding which component(s) were replaced in the vehicle.		# Include specific details regarding which component(s) were replaced in the vehicle.
	# Include specific details regarding the exact results when completing the basic settings procedure.<font color=white>E?ID=110711 and ST?ID=34591</font><br>		# Include specific details regarding the exact results when completing the basic settings procedure.<font color=white>E?ID=110711 and ST?ID=34591</font><br>