VW Golf VII (5G/AU) ABS Brakes - Revision history

Jef: /* Basic Setting */

2024-02-09T22:28:18Z

Basic Setting

← Older revision		Revision as of 22:28, 9 February 2024
Line 12:		Line 12:
	=== Steering Angle Sensor (G85) Calibration ===		=== Steering Angle Sensor (G85) Calibration ===
	* Steering Angle Sensor (G85) Calibration is completed in Address 44-Steering Assist. See [[EPS MQB]] for detals.		* Steering Angle Sensor (G85) Calibration is completed in Address 44-Steering Assist. See [[EPS MQB]] for detals.


	=== Brake Pressure Sensor 1 (G201) ===		=== Brake Pressure Sensor 1 (G201) ===

2024-02-09T22:27:18Z

Steering Angle Sensor (G85) Calibration

← Older revision		Revision as of 22:27, 9 February 2024
Line 11:		Line 11:

	=== Steering Angle Sensor (G85) Calibration ===		=== Steering Angle Sensor (G85) Calibration ===
	* Steering Angle Sensor (G85) Calibration is completed in Address 44-Steering Assist. See [~~https://forums.ross-tech.com/showthread.php?4224-~~MQB~~-(Mk7-Golf)-Steering-Angle-Sensor-(G85)-Calibration-in-44-Steering-Assist&p=144324&viewfull=1#post144324 this post~~]		* Steering Angle Sensor (G85) Calibration is completed in Address 44-Steering Assist. See [[EPS MQB]] for detals.


	=== Brake Pressure Sensor 1 (G201) ===		=== Brake Pressure Sensor 1 (G201) ===

2023-11-14T19:22:38Z

← Older revision		Revision as of 19:22, 14 November 2023
Line 29:		Line 29:
	'''[Go]'''<br>		'''[Go]'''<br>
	After a successful basic setting Finished Correctly or Not Running will be shown<br>		After a successful basic setting Finished Correctly or Not Running will be shown<br>
			'''[Stop]'''<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	~~'''[Stop]'''<br>~~



Line 51:		Line 50:
	'''[Go]'''<br>		'''[Go]'''<br>
	After a successful basic setting Finished Correctly or Not Running will be shown<br>		After a successful basic setting Finished Correctly or Not Running will be shown<br>
			'''[Stop]'''<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	~~'''[Stop]'''<br>~~

2023-11-10T20:12:08Z

@@ Line 9: / Line 9: @@
 == Basic Setting ==
 === Caution! ===
 * Do not perform any of these Basic Settings while the brakes are disassembled!  Opening, closing, function tests, and otherwise cycling the Electronic Parking brakes should only be done with the pads and calipers properly installed on the rotors.
 * Please follow the procedures EXACTLY.  There's a reason for every step.  If you skip any prerequisites or other steps here, you are likely to experience "issues" for which no documented resolutions exist, in which case we will not be able to help you resolve them.

2023-11-10T19:07:39Z

← Older revision		Revision as of 19:07, 10 November 2023
Line 1:		Line 1:
			__FORCETOC__

			This page applies to Golf 7 based 03-ABS Brake systems using Component: ESC. The Electro-Mechanical Parking Brake (EPB) system is NOT standard equipment in all of the models covered by this page.

			== Coding ==

			'''Coding for this Control Module is normally done via Software Version Management (SVM). If the old Control Module is still accessible read/copy it's Coding to the new Module.'''


	== Basic Setting ==		== Basic Setting ==
	=== Caution! ===		=== Caution! ===

2020-03-12T19:50:31Z

Open Rear Parking Brake

← Older revision		Revision as of 19:50, 12 March 2020
Line 7:		Line 7:
	=== Open Rear Parking Brake ===		=== Open Rear Parking Brake ===
	'''<u>Prerequisites:</u>'''<br>		'''<u>Prerequisites:</u>'''<br>
	* Connect a battery charger as per repair manual.		* Connect a battery charger as per repair manual. (For plug-ins like the e-Golf/Golf GTE/A3 e-tron/etc., connect the EV charging cable)
	* Cycle the Parking Brake ON, then OFF first.		* Cycle the Parking Brake ON, then OFF first.
	'''[Select]'''<br>		'''[Select]'''<br>

2018-02-27T21:57:45Z

← Older revision		Revision as of 21:57, 27 February 2018
Line 12:		Line 12:
	'''[03 - ABS Brakes]'''<br>		'''[03 - ABS Brakes]'''<br>
	'''[Basic Settings - 04]'''<br>		'''[Basic Settings - 04]'''<br>
	Select '''~~IStart~~ lining change mode'''''<br>		Select '''Start lining change mode'''''<br>
	'''[Go!]''' to activate the Basic Setting.<br>		'''[Go!]''' to activate the Basic Setting.<br>
	The brake calipers will then open, allowing the pads to be changed.<br>		The brake calipers will then open, allowing the pads to be changed.<br>

2017-05-22T18:07:52Z

← Older revision		Revision as of 18:07, 22 May 2017
Line 12:		Line 12:
	'''[03 - ABS Brakes]'''<br>		'''[03 - ABS Brakes]'''<br>
	'''[Basic Settings - 04]'''<br>		'''[Basic Settings - 04]'''<br>
	Select '''~~IDE03331-ENG114972 Start~~ lining change mode'''''<br>		Select '''IStart lining change mode'''''<br>
	'''[Go!]''' to activate the Basic Setting.<br>		'''[Go!]''' to activate the Basic Setting.<br>
	The brake calipers will then open, allowing the pads to be changed.<br>		The brake calipers will then open, allowing the pads to be changed.<br>
Line 29:		Line 29:
	'''[03 - ABS Brakes]'''<br>		'''[03 - ABS Brakes]'''<br>
	'''[Basic Settings - 04]'''<br>		'''[Basic Settings - 04]'''<br>
	Select '''~~IDE03330-ENG114972~~ End lining change mode'''''<br>		Select '''End lining change mode'''''<br>
	'''[Go!]''' to activate the Basic Setting.<br>		'''[Go!]''' to activate the Basic Setting.<br>
	The brake calipers will then close.<br>		The brake calipers will then close.<br>

2017-04-26T22:42:59Z

Close Rear Parking Brake

← Older revision		Revision as of 22:42, 26 April 2017
Line 37:		Line 37:
	* Turn ignition off<br>		* Turn ignition off<br>

	The LED in the parking brake switch and the warning lamp in the instrument cluster will probably continue to blink rapidly in addition to Fault code [[~~721152~~ \| ~~721152~~ - Brake pad replacement mode active]]. This should stop after cycling the Parking Brake ON, then OFF again using the switch in the vehicle while holding the brake pedal AFTER all rear brake components are reassembled.		The LED in the parking brake switch and the warning lamp in the instrument cluster will probably continue to blink rapidly in addition to Fault code [[C1011 \| C1011 - Brake pad replacement mode active]]. This should stop after cycling the Parking Brake ON, then OFF again using the switch in the vehicle while holding the brake pedal AFTER all rear brake components are reassembled.

2017-02-03T14:00:45Z

← Older revision		Revision as of 14:00, 3 February 2017
Line 12:		Line 12:
	'''[03 - ABS Brakes]'''<br>		'''[03 - ABS Brakes]'''<br>
	'''[Basic Settings - 04]'''<br>		'''[Basic Settings - 04]'''<br>
	Select '''Start lining change mode'''''<br>		Select '''IDE03331-ENG114972 Start lining change mode'''''<br>
	'''[Go!]''' to activate the Basic Setting.<br>		'''[Go!]''' to activate the Basic Setting.<br>
	The brake calipers will then open, allowing the pads to be changed.<br>		The brake calipers will then open, allowing the pads to be changed.<br>
Line 29:		Line 29:
	'''[03 - ABS Brakes]'''<br>		'''[03 - ABS Brakes]'''<br>
	'''[Basic Settings - 04]'''<br>		'''[Basic Settings - 04]'''<br>
	Select '''End lining change mode'''''<br>		Select '''IDE03330-ENG114972 End lining change mode'''''<br>
	'''[Go!]''' to activate the Basic Setting.<br>		'''[Go!]''' to activate the Basic Setting.<br>
	The brake calipers will then close.<br>		The brake calipers will then close.<br>