VW Jetta (16/AJ) Tweaks - Revision history

Dana: /* Alarm, Locking and Coming Home */

2017-10-04T14:03:14Z

Alarm, Locking and Coming Home

← Older revision		Revision as of 14:03, 4 October 2017
Line 87:		Line 87:
	'''Auto-UnLock'''		'''Auto-UnLock'''


			'''Remote operation when engine is running''' ''for vehicles with KESSY''
			* Found in Coding, "Remote Control with "Terminal 15 ON" active" would need to be enabled but this tweak would require the engine start button with KESSY.
			** Please note: VW/Audi have prevented alarm/locking activation with the door open and/or the ignition switched on to prevent the locking the vehicle with any of the keys inside it. This tweak will allow you to lock any spare ''or misplaced'' keys inside the vehicle!

	=== Windows ===		=== Windows ===

Dana: /* Lighting */

2017-08-30T18:11:37Z

Lighting

← Older revision		Revision as of 18:11, 30 August 2017
Line 65:		Line 65:
	'''NAR:'''		'''NAR:'''
	* The 2011+ Jetta and 2012 Beelte from the US/Canadian (NAR) market use a hardwired "TFL" signal into the BCM for DRL operation. This input is not monitored by the BCM for fault code recognition and simply removing the "TFL" pin at the headlight switch will disable DRL operation.<br>		* The 2011+ Jetta and 2012 Beelte from the US/Canadian (NAR) market use a hardwired "TFL" signal into the BCM for DRL operation. This input is not monitored by the BCM for fault code recognition and simply removing the "TFL" pin at the headlight switch will disable DRL operation.<br>
			'''NAR 2017+ Facelift LED DRLs.'''
			* Discussion related to 2017 NAR market Jetta headlights with LED DRLs can be found here: [http://forums.ross-tech.com/showthread.php?8859-2017-Jetta-SE-TSI-DRL-wink 2017 Jetta SE TSI DRL wink]
			** See post #8 for coding observations.<br>
	'''RoW:'''		'''RoW:'''
	* It is unclear at this time if other makes/models/brands outside of the NAR markets use actual coding alone, however several bits are available in the Long Coding Helper. If coding does not disable the DRL operation refer to the wiring diagrams and experiment with the TFL pin mentioned above.		* It is unclear at this time if other makes/models/brands outside of the NAR markets use actual coding alone, however several bits are available in the Long Coding Helper. If coding does not disable the DRL operation refer to the wiring diagrams and experiment with the TFL pin mentioned above.
	** Seat Ibiza (6J) owners have reported success with coding alone, but Polo (6R) owners have not.		** Seat Ibiza (6J) owners have reported success with coding alone, but Polo (6R) owners have not.
	** Registered customers can [http://~~www~~.ross-tech.com/~~contact~~.~~html contact us directly], sending~~ a complete Auto-Scan.		** Registered customers can [http://forums.ross-tech.com/forum.php join and post in a complete Auto-Scan in our forum].
			<font color=white>E?ID=110407</font>
	<br>		<br>
	<~~font color=white~~>~~E?ID=110407</font>~~		'''All markets'''<br>

	'''<font color=red>Byte 18</font>''' - '''Do Not alter this if you are not retrofitting rear lights !'''		'''<font color=red>Byte 18</font>''' - '''Do Not alter this if you are not retrofitting rear lights !'''



	=== Alarm, Locking and Coming Home ===		=== Alarm, Locking and Coming Home ===

Dana at 13:11, 3 June 2014

2014-06-03T13:11:15Z

← Older revision		Revision as of 13:11, 3 June 2014
Line 3:		Line 3:
	'''Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk'''.<br>		'''Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk'''.<br>

	These instructions apply to the [[VW Jetta (16/AJ)]] MY 2011+		These instructions apply to the [[VW Jetta (16/AJ)]] MY 2011+ and [[VW Beetle (5C/AT) \| VW Beetle (5C/AT/16)]] with BCM25 -or- PQ25 control modules.

	* It is always recommended to perform a complete Auto-Scan and save it prior to coding changes. Please see the Online Manual: [http://www.ross-tech.com/vcds/tour/autoscan.html Auto Scan Screen]		* It is always recommended to perform a complete Auto-Scan and save it prior to coding changes. Please see the Online Manual: [http://www.ross-tech.com/vcds/tour/autoscan.html Auto Scan Screen]

Dana at 16:48, 19 June 2013

2013-06-19T16:48:35Z

@@ Line 96: / Line 96: @@
 <br>
 ----
 === [17] - Instrument Cluster ===

Dana at 16:00, 9 August 2012

2012-08-09T16:00:42Z

← Older revision		Revision as of 16:00, 9 August 2012
Line 137:		Line 137:
	----		----

			=== [77] - Telephone ===
			Some of the long codes 9W7 and similar telephone (Bluetooth) modules may support phone book sorting order by:

			# First Name
			# Last Name

			If the module installed in the vehicle supports this modification simply open the Long Coding Helper while connected to the vehicle and look for the "Phone Book" option to see if it is present.


			----
	=== Retrofits ===		=== Retrofits ===

	Some of the common retrofits are found in the Ross-Tech Wiki in this location: [[Retrofitting]].<br>		Some of the common retrofits are found in the Ross-Tech Wiki in this location: [[Retrofitting]].<br>
	Additional retrofitting links and information can be found at the bottom of this forum thread: [http://forums.vwvortex.com/showthread.php?4743553-VCDS-MKVI-MK6-Platform-Handy-Coding-tweaks VCDS MKVI / MK6 Platform, Handy Coding tweaks]		Additional retrofitting links and information can be found at the bottom of this forum thread: [http://forums.vwvortex.com/showthread.php?4743553-VCDS-MKVI-MK6-Platform-Handy-Coding-tweaks VCDS MKVI / MK6 Platform, Handy Coding tweaks]

Dana at 17:00, 19 June 2012

2012-06-19T17:00:30Z

← Older revision		Revision as of 17:00, 19 June 2012
Line 71:		Line 71:
	** Registered customers can [http://www.ross-tech.com/contact.html contact us directly], sending a complete Auto-Scan.		** Registered customers can [http://www.ross-tech.com/contact.html contact us directly], sending a complete Auto-Scan.
	<br>		<br>
			<font color=white>E?ID=110407</font>

	'''<font color=red>Byte 18</font>''' - '''Do Not alter this if you are not retrofitting rear lights !'''		'''<font color=red>Byte 18</font>''' - '''Do Not alter this if you are not retrofitting rear lights !'''

Dana at 21:48, 19 January 2012

2012-01-19T21:48:35Z

← Older revision		Revision as of 21:48, 19 January 2012
Line 69:		Line 69:
	* It is unclear at this time if other makes/models/brands outside of the NAR markets use actual coding alone, however several bits are available in the Long Coding Helper. If coding does not disable the DRL operation refer to the wiring diagrams and experiment with the TFL pin mentioned above.		* It is unclear at this time if other makes/models/brands outside of the NAR markets use actual coding alone, however several bits are available in the Long Coding Helper. If coding does not disable the DRL operation refer to the wiring diagrams and experiment with the TFL pin mentioned above.
	** Seat Ibiza (6J) owners have reported success with coding alone, but Polo (6R) owners have not.		** Seat Ibiza (6J) owners have reported success with coding alone, but Polo (6R) owners have not.
			** Registered customers can [http://www.ross-tech.com/contact.html contact us directly], sending a complete Auto-Scan.
	<br>		<br>

Dana at 20:59, 19 January 2012

2012-01-19T20:59:45Z

← Older revision		Revision as of 20:59, 19 January 2012
Line 60:		Line 60:
	* Turning On/Off the feature is found in Adaptation. Select "Lights: Comfort Turn Signals" from the drop down list, choose 0 = Comfort Turn Signals inactive -OR- 1 = Comfort Turn Signals active.<br>		* Turning On/Off the feature is found in Adaptation. Select "Lights: Comfort Turn Signals" from the drop down list, choose 0 = Comfort Turn Signals inactive -OR- 1 = Comfort Turn Signals active.<br>


			'''Daytime Running Lights (DRL)'''<br>

			'''NAR:'''
			* The 2011+ Jetta and 2012 Beelte from the US/Canadian (NAR) market use a hardwired "TFL" signal into the BCM for DRL operation. This input is not monitored by the BCM for fault code recognition and simply removing the "TFL" pin at the headlight switch will disable DRL operation.<br>

			'''RoW:'''
			* It is unclear at this time if other makes/models/brands outside of the NAR markets use actual coding alone, however several bits are available in the Long Coding Helper. If coding does not disable the DRL operation refer to the wiring diagrams and experiment with the TFL pin mentioned above.
			** Seat Ibiza (6J) owners have reported success with coding alone, but Polo (6R) owners have not.

			<br>

	'''<font color=red>Byte 18</font>''' - '''Do Not alter this if you are not retrofitting rear lights !'''		'''<font color=red>Byte 18</font>''' - '''Do Not alter this if you are not retrofitting rear lights !'''

Dana: Created page with 'FORCETOC '''Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk'''.
These in…'

2011-07-27T04:16:20Z

Created page with '__FORCETOC__ '''Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk'''. These in…'

New page

__FORCETOC__

'''Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk'''. 

These instructions apply to the [[VW Jetta (16/AJ)]] MY 2011+

* It is always recommended to perform a complete Auto-Scan and save it prior to coding changes. Please see the Online Manual: [http://www.ross-tech.com/vcds/tour/autoscan.html Auto Scan Screen]
* Never Copy coding from a different vehicle and Paste it to your module(s)! 

''The installed control modules vary by vendor, firmware level and equipment level, some of the noted tweaks may not be supported by all control modules/vehicles.'' 

----

=== [03] - Brake Electronics ===

On Vehicles using the [[VW Golf (1K) Brake Electronics (MK60EC1) | MK60EC1]] ABS system it may be possible to:
* Alter the HHA (Hill Hold Assist) using the documented '''[http://www.ross-tech.com/vcds/tour/adaptation_screen.html [Adaptation -10]]''' Channel while connected to the vehicle. 

* Enable Indirect TPMS using the documented Long Coding Helper information and the forum feedback here: [http://www.vwwatercooled.org.au/f112/how-retrofit-indirect-tire-pressure-monitoring-5-minutes-7k6-50164.html How to: retrofit indirect Tire Pressure Monitoring in 5 minutes. (7K6) ] 

----

=== [08] - Heating/Air Conditioning ===

'''Drivers heated seat memory''' 
The Driver side heated seat level (i.e. 1, 2 or 3) should resume the previous level upon restarting the car.
* Found in Adaptation. From the drop down list, choose Storage of seat heater level driver. Change to On and Save.
** ''This may not be supported on all control modules.''

----

=== [09] - Central Electronics / Body Control Module (BCM) ===

'''Note''': ''Make sure to have all Doors unlocked, otherwise this Control Module may not communicate with the Scan Tool / VCDS.

=== Lighting ===

All modifications are found in Found in '''[Coding - 07]''' > '''[http://www.ross-tech.com/vcds/tour/recode_screen.html Long Coding Helper]''' unless otherwise noted. Click on each of the Bytes and Bits for the documented options and check or un-check the appropriate boxes as shown in the example below: 

'''[Select]''' 
'''[09 - Cent. Elect.]''' ''Or the module you intend on tweaking as per the list below'' 
'''[Coding - 07]''' 
'''[Long Coding Helper]''' 
Click on each of the Byte numbers in row '''3''') and you'll see the selectable options below. Check or Un-check the boxes for the desired results. ''Example: Comfort Function for Power Windows via Remote Control active'' 

Close the Long Coding Helper by clicking the Windows X box on the top right of the screen or clicking the Exit button on the top left of the screen to send your altered Coding value back to the Coding screen. 
'''[Do It!]''' 
. 

'''Comfort Turn signals''' Number of flashes and turning On/Off the feature
* Number of flashes found in Adaptation. Select "Lights: Comfort Turn Signals (Cycles)" from the drop down list, choose the number of flashes and Save.
* Coding or MFA / dash options may apply to this setting in some cases. 

Note: MY 2011 Golf owners reported: [http://forums.vwvortex.com/showthread.php?5006547-Change-comfort-turn-signals-count-in-MKVI&p=70065688&viewfull=1#post70065688 Change comfort turn signals count in the VW Vortex] 
 
* Turning On/Off the feature is found in Adaptation. Select "Lights: Comfort Turn Signals" from the drop down list, choose 0 = Comfort Turn Signals inactive -OR- 1 = Comfort Turn Signals active. 

'''Byte 18''' - '''Do Not alter this if you are not retrofitting rear lights !'''

=== Alarm, Locking and Coming Home ===

Options are primarily found in Coding, '''Long Coding helper'''. Some Adaptation Channels may be available after enabling coding options.

'''Alarm Confirmation via lights and horn'''

'''Auto-Lock'''

'''Auto-UnLock'''

=== Windows ===

'''Windows up via remote'''
Comfort Operation (via Remote Control)
* Found in Coding, Long Coding Helper "Comfort Function for Power Windows via Remote Control active". 
 
 
----

=== [17] - Instrument Cluster ===

'''Staging''' 
The gauge needles should sweep from default to max upon starting the car. ''This is Not supported on all instrument clusters.'' 
* Found in '''[http://www.ross-tech.com/vcds/tour/adaptation_screen.html [Adaptation -10]]'''. From the drop down list, choose Staging. Change to On and Save.
** Forum Staging feedback here: [http://forums.vwvortex.com/showthread.php?4802735 MkVI Instrument cluster - which one do you have?] 

'''Seat Belt Light''' May remove the chime as well 
* Found in Coding, Long Coding helper. 

'''Service Interval Reset''' 
* Found in Adaptation, Choose "ESI: Resetting ESI" from the drop-down menu. 

* Most North American vehicles with the UDS/ODX protocol instrument clusters have a "Reset" that can be accessed via the MFA, without a scan tool. Pictures here: 
# [http://i778.photobucket.com/albums/yy64/Dana_at_Ross-Tech/Cluster/DSC02170.jpg Service Menu]
# [http://i778.photobucket.com/albums/yy64/Dana_at_Ross-Tech/Cluster/DSC02173.jpg Service Reset]
# [http://i778.photobucket.com/albums/yy64/Dana_at_Ross-Tech/Cluster/DSC02171.jpg Service Info] 

'''Modify Service Intervals Mileage and Time''' 
* Found in Adaptation, Choose "SID: maximum value of distance to service" or "SID: maximum value of time to service" 

'''Fuel Gauge and Fuel Consumption Adaption''' 
* Found in Adaptation
** See the notes in this forum which apply to most newer (UDS) clusters: [http://forums.vwvortex.com/showthread.php?4868432-Fuel-Gauge-Adaption-2010-Jetta&p=66099017&viewfull=1#post66099017 Fuel Gauge Adaption] 

----

=== [46] - Comfort System ===

'''Note''': ''The Comfort System known from earlier Models has been integrated with the Central Electronics / Body Control Module (BCM) and is no longer available as a separate Address/Module. All related Diagnostics/Settings have to be performed via Central Electronics / Body Control Module (BCM).''

----

=== Retrofits ===

Some of the common retrofits are found in the Ross-Tech Wiki in this location: [[Retrofitting]]. 
Additional retrofitting links and information can be found at the bottom of this forum thread: [http://forums.vwvortex.com/showthread.php?4743553-VCDS-MKVI-MK6-Platform-Handy-Coding-tweaks VCDS MKVI / MK6 Platform, Handy Coding tweaks]