VW Passat (3C) Trunk Electronics - Revision history

Dana at 14:21, 30 September 2018

2018-09-30T14:21:06Z

← Older revision		Revision as of 14:21, 30 September 2018
Line 16:		Line 16:

	== Special Notes ==		== Special Notes ==
	This thread may be helpful it the top stop of the tailgate cannot be adjusted properly using the General Information below: [https://forums.ross-tech.com/showthread.php?15735-Powered-Tailgate-minor-issue Powered Tailgate minor issue]		This thread may be helpful if the top stop of the tailgate cannot be adjusted properly using the General Information below: [https://forums.ross-tech.com/showthread.php?15735-Powered-Tailgate-minor-issue Powered Tailgate minor issue]

	== General Information ==		== General Information ==

Dana at 22:25, 29 September 2018

2018-09-29T22:25:39Z

← Older revision		Revision as of 22:25, 29 September 2018
Line 14:		Line 14:
	== Coding ==		== Coding ==
	* This control module does not support Coding.		* This control module does not support Coding.

			== Special Notes ==
			This thread may be helpful it the top stop of the tailgate cannot be adjusted properly using the General Information below: [https://forums.ross-tech.com/showthread.php?15735-Powered-Tailgate-minor-issue Powered Tailgate minor issue]

	== General Information ==		== General Information ==

Dana at 20:20, 19 May 2016

2016-05-19T20:20:49Z

← Older revision		Revision as of 20:20, 19 May 2016
Line 21:		Line 21:
	* If the power close function is not working when power opening works properly check the luggage compartment light (W3) functionality. If W3 is not operating properly check the powers and grounds to the light in addition to measuring block data for the F5/F256/V254 rear latch motor assembly. A failed W3 light assembly may be responsible for feedback however rear latch motor/micro-switch failure isn't unheard of.		* If the power close function is not working when power opening works properly check the luggage compartment light (W3) functionality. If W3 is not operating properly check the powers and grounds to the light in addition to measuring block data for the F5/F256/V254 rear latch motor assembly. A failed W3 light assembly may be responsible for feedback however rear latch motor/micro-switch failure isn't unheard of.
	** The factory level Comfort System wiring diagram will clarify the relationship of the above mentioned components.		** The factory level Comfort System wiring diagram will clarify the relationship of the above mentioned components.


			''Internal ref: ST?ID=67792''

Dana at 16:46, 19 May 2016

2016-05-19T16:46:59Z

← Older revision		Revision as of 16:46, 19 May 2016
Line 19:		Line 19:
	* When replacing the master (J605) or slave (J756) control module with integrated motors it may be necessary to initialize the new parts. Hold the exterior hatch button in addition to the hatch closing button in the rear hatch trim for 5 seconds. The comfort system should confirm the learning completed by flashing the lights or beeping the siren.		* When replacing the master (J605) or slave (J756) control module with integrated motors it may be necessary to initialize the new parts. Hold the exterior hatch button in addition to the hatch closing button in the rear hatch trim for 5 seconds. The comfort system should confirm the learning completed by flashing the lights or beeping the siren.
	* When adapting the opening height (top stop) of the hatch raise the lid to the desired height followed by holding hatch closing button in the rear hatch trim for 5 - 10 seconds. After doing so the Comfort system should confirm the learning completed by flashing the lights.		* When adapting the opening height (top stop) of the hatch raise the lid to the desired height followed by holding hatch closing button in the rear hatch trim for 5 - 10 seconds. After doing so the Comfort system should confirm the learning completed by flashing the lights.
	* If the power close function is not working when power opening works properly check the luggage compartment light (W3) functionality. If W3 is not operating properly check the powers and grounds to the light in addition to measuring block data for the F5/F256/V254 rear latch motor assembly. A failed W3 light assembly may be responsible for feedback however rear latch motor failure isn't unheard of.		* If the power close function is not working when power opening works properly check the luggage compartment light (W3) functionality. If W3 is not operating properly check the powers and grounds to the light in addition to measuring block data for the F5/F256/V254 rear latch motor assembly. A failed W3 light assembly may be responsible for feedback however rear latch motor/micro-switch failure isn't unheard of.
	** The factory level Comfort System wiring diagram will clarify the relationship of the above mentioned components.		** The factory level Comfort System wiring diagram will clarify the relationship of the above mentioned components.

Dana at 22:28, 18 May 2016

2016-05-18T22:28:19Z

← Older revision		Revision as of 22:28, 18 May 2016
Line 16:		Line 16:

	== General Information ==		== General Information ==
	* When replacing the master or slave control module with integrated motors it may be necessary to initialize the new parts. ~~A scan tool is not used for this initialization.~~ Hold the exterior hatch button in addition to the hatch closing button in the rear hatch trim for 5 seconds. The comfort system should confirm the learning completed by flashing the lights or beeping the siren.		A scan tool is not used for the following operations and fault codes are NOT generally stored when they are necessary.
			* When replacing the master (J605) or slave (J756) control module with integrated motors it may be necessary to initialize the new parts. Hold the exterior hatch button in addition to the hatch closing button in the rear hatch trim for 5 seconds. The comfort system should confirm the learning completed by flashing the lights or beeping the siren.
			* When adapting the opening height (top stop) of the hatch raise the lid to the desired height followed by holding hatch closing button in the rear hatch trim for 5 - 10 seconds. After doing so the Comfort system should confirm the learning completed by flashing the lights.
			* If the power close function is not working when power opening works properly check the luggage compartment light (W3) functionality. If W3 is not operating properly check the powers and grounds to the light in addition to measuring block data for the F5/F256/V254 rear latch motor assembly. A failed W3 light assembly may be responsible for feedback however rear latch motor failure isn't unheard of.
			** The factory level Comfort System wiring diagram will clarify the relationship of the above mentioned components.

Dana: Created page with "FORCETOC This page applies to Address-6D: Trunk Elect.in the VW Passat (3C) Wagon with Component: J605 HECKDECKEL. This can be identified by evaluating the data in the Au..."

2016-05-18T20:34:58Z

Created page with "__FORCETOC__ This page applies to Address-6D: Trunk Elect.in the VW Passat (3C) Wagon with Component: J605 HECKDECKEL. This can be identified by evaluating the data in the Au..."

New page

__FORCETOC__
This page applies to Address-6D: Trunk Elect.in the VW Passat (3C) Wagon with Component: J605 HECKDECKEL. This can be identified by evaluating the data in the Auto-Scan:

Address 6D: Trunk Elect. Labels: None
Part No SW: 3C9 827 383 B HW: 3C9 827 383 E
Component: J605 HECKDECKEL 0600
Revision: 00H21001

Subsystem 1 - Part No: 3C9 827 384 B
Component: J756 HECKDECKEL 0600

Subsystem 2 - Serial number:

== Coding ==
* This control module does not support Coding.

== General Information ==
* When replacing the master or slave control module with integrated motors it may be necessary to initialize the new parts. A scan tool is not used for this initialization. Hold the exterior hatch button in addition to the hatch closing button in the rear hatch trim for 5 seconds. The comfort system should confirm the learning completed by flashing the lights or beeping the siren.