VW Touareg (7L) Airbag - Revision history

RtWiKiSyS0p at 15:01, 11 April 2007

2007-04-11T15:01:59Z

← Older revision		Revision as of 15:01, 11 April 2007
Line 28:		Line 28:
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Close Controller, Go Back - 06]'''<br><br>		'''[Close Controller, Go Back - 06]'''<br><br>

			== Output Test ==

			'''''Important Note:''' Please do NOT run Output Tests (function 03) on your Airbag Controller!''<br>
			''No, it won't deploy your airbags. But it MAY render the vehicle undrivable. Running Output Tests is supposed to make the airbag controller generate a simulated crash signal to the rest of the systems in the vehicle so that unlocks itself and shuts various things OFF. Unfortunately, one of the things it shuts off in the Touareg is the power supply to the Engine Control Module. Two things are needed (confirmed by a dealer tech who was brave enough to run Output Tests on an Airbag Module):''
			# Clear "Crash Data" code from the DTC Screen in 25 - Immobilizer.
			# Reset the yellow Circuit breaker under driver's seat. The circuit breaker should be yellow and should be visible/accessible if you remove the carpeted "step" trim panel at the front of the seat (an operation requiring some dexterity, but no tools).
			''Beginning with Beta 310.0, VAG-COM will pop up a warning if you try to run Output Tests on the Airbag Controller.''

	== Special Procedures ==		== Special Procedures ==

RtWiKiSyS0p at 14:36, 20 April 2006

2006-04-20T14:36:30Z

← Older revision		Revision as of 14:36, 20 April 2006
Line 17:		Line 17:
	'''[Select]'''<br>		'''[Select]'''<br>
	'''[15 - Airbags]'''<br>		'''[15 - Airbags]'''<br>
	'''[~~Coding~~-~~II - 11~~]'''<br>		'''[Security Access - 16]'''<br>
	Enter 30475, to enable the basic setting.<br>		Enter 30475, to enable the basic setting.<br>
	'''[Do it!]'''<br>		'''[Do it!]'''<br>
Line 44:		Line 44:
	'''[Select]'''<br>		'''[Select]'''<br>
	'''[15 - Airbags]'''<br>		'''[15 - Airbags]'''<br>
	'''[~~Coding~~-~~II - 11~~]'''<br>		'''[Security Access - 16]'''<br>
	Enter 30475, to enable the basic setting.<br>		Enter 30475, to enable the basic setting.<br>
	'''[Do it!]'''<br>		'''[Do it!]'''<br>

RtWiKiSyS0p at 13:20, 20 April 2006

2006-04-20T13:20:28Z

← Older revision		Revision as of 13:20, 20 April 2006
Line 26:		Line 26:
	'''[ON/OFF/Next]'''<br>		'''[ON/OFF/Next]'''<br>
	The reset has been performed.<br>		The reset has been performed.<br>
	'''[Done, Go Back]'''<br><br>		'''[Done, Go Back]'''<br>
			'''[Close Controller, Go Back - 06]'''<br><br>

	== Special Procedures ==		== Special Procedures ==
Line 50:		Line 51:
	'''[Read]'''<br>		'''[Read]'''<br>
	'''[Save]'''<br>		'''[Save]'''<br>
	'''[Done, Go Back]'''<br><br>		'''[Done, Go Back]'''<br>
			'''[Close Controller, Go Back - 06]'''<br><br>

RtWiKiSyS0p at 12:16, 20 April 2006

2006-04-20T12:16:44Z

New page

__FORCETOC__

== Coding ==

VAG-COM will automatically tell you a suggested coding (HEX interface required), otherwise [http://www.ross-tech.com/contact.html contact us] for assistance. 

== Adaptation ==

Used to deactivate individual airbag components (see repair manual for details). 

== Basic Setting ==

=== Seat Occupied Recognition Control Module (J706) ===

If the Seat Occupied Recognition Control Module (J706) or the seat itself have been replaced, the basic setting has to be performed.

'''[Select]''' 
'''[15 - Airbags]''' 
'''[Coding-II - 11]''' 
Enter 30475, to enable the basic setting. 
'''[Do it!]''' 
'''[Basic Settings - 04]''' 
Group 001 
'''[Go!]''' 
Activate the Basic Setting. 
'''[ON/OFF/Next]''' 
The reset has been performed. 
'''[Done, Go Back]''' 

== Special Procedures ==

=== Seat Occupied Recognition Control Module (J706): Reset ===

If a repair on the Seat Occupied Recognition has been performed, a reset has to be performed too.

'''Prerequisites:'''
* Seat in normal position.
* Seat must NOT be occupied during the whole procedure.
* Seatbelt must NOT be plugged in.
* No faults in the system.
* Interior temperature must be between 0 °C and 37 °C (32 °F and 98 °F). 

'''[Select]''' 
'''[15 - Airbags]''' 
'''[Coding-II - 11]''' 
Enter 30475, to enable the basic setting. 
'''[Do it!]''' 
'''[Adaptation - 10]''' 
Channel 000 
'''[Read]''' 
'''[Save]''' 
'''[Done, Go Back]'''