https://wiki.ross-tech.com/wiki/index.php?action=history&feed=atom&title=VW_Touareg_%287L%29_Brake_Electronics 2026-05-13T21:58:34Z Revision history for this page on the wiki MediaWiki 1.43.3 https://wiki.ross-tech.com/wiki/index.php?title=VW_Touareg_(7L)_Brake_Electronics&diff=3654&oldid=prev 2007-05-09T16:43:55Z

<p></p> <p><b>New page</b></p><div>__FORCETOC__<br /> == Coding ==<br /> <br /> == Basic Setting ==<br /> <br /> === Sensor for Steering Angle (G85) ===<br /> <br /> &#039;&#039;&#039;&lt;u&gt;Prerequisites:&lt;/u&gt;&#039;&#039;&#039;&lt;br&gt;<br /> * Start the vehicle.<br /> * Turn the steering wheel one turn to the right and one turn to the left.<br /> * Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.<br /> * If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight.<br /> * Ensure that the steering wheel is not moved again.<br /> * Keep the engine running and do not switch off the ignition.<br /> * System voltage at least 12.0 V.&lt;br&gt;&lt;br&gt;<br /> <br /> &#039;&#039;&#039;[Select]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[03 - Brake Electronics]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Coding-II - 11]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;OR&#039;&#039;&#039; &#039;&#039;(if Coding-II is not available)&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Security Access - 16]&#039;&#039;&#039;&lt;br&gt;<br /> Enter 40168, to enable the basic setting.&lt;br&gt;<br /> &#039;&#039;&#039;[Do it!]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Basic Settings - 04]&#039;&#039;&#039;&lt;br&gt;<br /> Group 060&lt;br&gt;<br /> &#039;&#039;&#039;[Go!]&#039;&#039;&#039;&lt;br&gt;<br /> Activate the Basic Setting.&lt;br&gt;<br /> &#039;&#039;&#039;[ON/OFF/Next]&#039;&#039;&#039;&lt;br&gt;<br /> After a successful basic setting, field 2 should say &quot;OK&quot;.&lt;br&gt;<br /> &#039;&#039;&#039;[Done, Go Back]&#039;&#039;&#039;&lt;br&gt;<br /> To make sure the basic setting was succesful, check the sensor again.&lt;br&gt;<br /> &#039;&#039;&#039;[Measuring Blocks - 08]&#039;&#039;&#039;&lt;br&gt;<br /> Group 004&lt;br&gt;<br /> &#039;&#039;&#039;[Go!]&#039;&#039;&#039;&lt;br&gt;<br /> Check field 1, the value has to be between -1.5 and +1.5 °.&lt;br&gt;<br /> &#039;&#039;&#039;[Done, Go Back]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Close Controller, Go Back - 06]&#039;&#039;&#039;&lt;br&gt;<br /> <br /> <br /> === Lateral Acceleration Sensor (G200) ===<br /> <br /> &#039;&#039;&#039;&lt;u&gt;Prerequisites:&lt;/u&gt;&#039;&#039;&#039;&lt;br&gt;<br /> * System voltage at least 12.0 V.&lt;br&gt;&lt;br&gt;<br /> <br /> &#039;&#039;&#039;[Select]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[03 - Brake Electronics]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Measuring Blocks - 08]&#039;&#039;&#039;&lt;br&gt;<br /> Group 004&lt;br&gt;<br /> &#039;&#039;&#039;[Go!]&#039;&#039;&#039;&lt;br&gt;<br /> Check field 2, the value has to be between -1.5 and +1.5 m/s².&lt;br&gt;<br /> &#039;&#039;&#039;[Done, Go Back]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Coding-II - 11]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;OR&#039;&#039;&#039; &#039;&#039;(if Coding-II is not available)&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Security Access - 16]&#039;&#039;&#039;&lt;br&gt;<br /> Enter 40168, to enable the basic setting.&lt;br&gt;<br /> &#039;&#039;&#039;[Do it!]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Basic Settings - 04]&#039;&#039;&#039;&lt;br&gt;<br /> Group 063&lt;br&gt;<br /> &#039;&#039;&#039;[Go!]&#039;&#039;&#039;&lt;br&gt;<br /> Activate the Basic Setting.&lt;br&gt;<br /> &#039;&#039;&#039;[ON/OFF/Next]&#039;&#039;&#039;&lt;br&gt;<br /> After a successful basic setting, field 2 should say &quot;OK&quot;.&lt;br&gt;<br /> &#039;&#039;&#039;[Done, Go Back]&#039;&#039;&#039;&lt;br&gt;<br /> To make sure the basic setting was succesful, check the sensor again.&lt;br&gt;<br /> &#039;&#039;&#039;[Measuring Blocks - 08]&#039;&#039;&#039;&lt;br&gt;<br /> Group 004&lt;br&gt;<br /> &#039;&#039;&#039;[Go!]&#039;&#039;&#039;&lt;br&gt;<br /> Check field 2, the value has to be between -1.5 and +1.5 m/s².&lt;br&gt;<br /> &#039;&#039;&#039;[Done, Go Back]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Close Controller, Go Back - 06]&#039;&#039;&#039;&lt;br&gt;&lt;br&gt;&lt;br&gt;<br /> <br /> <br /> === Brake Pressure Sensor 1 (G201) ===<br /> <br /> &#039;&#039;&#039;&lt;u&gt;Prerequisites:&lt;/u&gt;&#039;&#039;&#039;&lt;br&gt;<br /> * System voltage at least 12.0 V.&lt;br&gt;&lt;br&gt;<br /> <br /> &#039;&#039;&#039;[Select]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[03 - Brake Electronics]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Measuring Blocks - 08]&#039;&#039;&#039;&lt;br&gt;<br /> Group 005&lt;br&gt;<br /> &#039;&#039;&#039;[Go!]&#039;&#039;&#039;&lt;br&gt;<br /> Check field 1, the value has to be between -8.0 and +8.0 bar.&lt;br&gt;<br /> &#039;&#039;&#039;[Done, Go Back]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Coding-II - 11]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;OR&#039;&#039;&#039; &#039;&#039;(if Coding-II is not available)&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Security Access - 16]&#039;&#039;&#039;&lt;br&gt;<br /> Enter 40168, to enable the basic setting.&lt;br&gt;<br /> &#039;&#039;&#039;[Do it!]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Basic Settings - 04]&#039;&#039;&#039;&lt;br&gt;<br /> Group 066&lt;br&gt;<br /> &#039;&#039;&#039;[Go!]&#039;&#039;&#039;&lt;br&gt;<br /> Activate the Basic Setting.&lt;br&gt;<br /> &#039;&#039;&#039;[ON/OFF/Next]&#039;&#039;&#039;&lt;br&gt;<br /> After a successful basic setting, field 2 should say &quot;OK&quot;.&lt;br&gt;<br /> &#039;&#039;&#039;[Done, Go Back]&#039;&#039;&#039;&lt;br&gt;<br /> To make sure the basic setting was succesful, check the sensor again.&lt;br&gt;<br /> &#039;&#039;&#039;[Measuring Blocks - 08]&#039;&#039;&#039;&lt;br&gt;<br /> Group 005&lt;br&gt;<br /> &#039;&#039;&#039;[Go!]&#039;&#039;&#039;&lt;br&gt;<br /> Check field 1, the value has to be between -7.0 and +7.0 bar.&lt;br&gt;<br /> &#039;&#039;&#039;[Done, Go Back]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Close Controller, Go Back - 06]&#039;&#039;&#039;&lt;br&gt;&lt;br&gt;&lt;br&gt;<br /> <br /> <br /> === Longitudinal Acceleration Sensor (G251) ===<br /> <br /> &#039;&#039;&#039;&lt;u&gt;Prerequisites:&lt;/u&gt;&#039;&#039;&#039;&lt;br&gt;<br /> * System voltage at least 12.0 V.&lt;br&gt;&lt;br&gt;<br /> <br /> &#039;&#039;&#039;[Select]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[03 - Brake Electronics]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Measuring Blocks - 08]&#039;&#039;&#039;&lt;br&gt;<br /> Group 004&lt;br&gt;<br /> &#039;&#039;&#039;[Go!]&#039;&#039;&#039;&lt;br&gt;<br /> Check field 4, the value has to be between -1.5 and +1.5 m/s².&lt;br&gt;<br /> &#039;&#039;&#039;[Done, Go Back]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Coding-II - 11]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;OR&#039;&#039;&#039; &#039;&#039;(if Coding-II is not available)&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Security Access - 16]&#039;&#039;&#039;&lt;br&gt;<br /> Enter 40168, to enable the basic setting.&lt;br&gt;<br /> &#039;&#039;&#039;[Do it!]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Basic Settings - 04]&#039;&#039;&#039;&lt;br&gt;<br /> Group 069&lt;br&gt;<br /> &#039;&#039;&#039;[Go!]&#039;&#039;&#039;&lt;br&gt;<br /> Activate the Basic Setting.&lt;br&gt;<br /> &#039;&#039;&#039;[ON/OFF/Next]&#039;&#039;&#039;&lt;br&gt;<br /> After a successful basic setting, field 2 should say &quot;OK&quot;.&lt;br&gt;<br /> &#039;&#039;&#039;[Done, Go Back]&#039;&#039;&#039;&lt;br&gt;<br /> To make sure the basic setting was succesful, check the sensor again.&lt;br&gt;<br /> &#039;&#039;&#039;[Measuring Blocks - 08]&#039;&#039;&#039;&lt;br&gt;<br /> Group 006&lt;br&gt;<br /> &#039;&#039;&#039;[Go!]&#039;&#039;&#039;&lt;br&gt;<br /> Check field 1, the value has to be between -1.5 and +1.5 m/s².&lt;br&gt;<br /> &#039;&#039;&#039;[Done, Go Back]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[Close Controller, Go Back - 06]&#039;&#039;&#039;&lt;br&gt;<br /> <br /> <br /> == Special Procedures ==<br /> <br /> === System Function Test ===<br /> <br /> See [[ESP System Function Test (Conti/Teves)|System Function Test]]</div>

RtWiKiSyS0p