VW Golf (1J) Brake Electronics (MK60)

Coding

ABS

• 0001025 = Cable-Throttle Engines
• 0004097 = Drive-By-Wire Engines

ABS/EDS/ASR/ESP (Front-Wheel-Drive)

• Frontbrakes:
  • +0000002 = FS III 54 15" (PR-1LS/1LQ/1ZM/1ZF)
  • +0000514 = FN III 54 15"/16" (PR-1LE/1LJ/1ZE)
• Suspension:
  • +0000000 = Standard/Sport Suspension (PR-2UA)
  • +0000128 = Rough Road Suspension (PR-2UB)
• Engine I:
  • +0010240 = Gasoline Engine (through 92 kW / 125 HP)
  • +0018432 = Gasoline Engine (from 92 kW / 125 HP) & All Diesel Engines
• Engine II
  • +0001024 = Drive-By-Wire Engines
  • +0004096 = Cable-Throttle Engines

Notes: See production codes on car data plate. Coding is the sum of the individual options.
Seat Leon Cupra R: Unlike the above coding chart, the Cupra R has a different coding 0019469.

ABS/EDS/ASR/ESP (All-Wheel-Drive)

• Frontbrakes:
  • +0000006 = FS III 54 14"/15" (PR-1LS/1LQ/1ZM/1ZF)
  • +0000518 = FN III 54 15"/16" (PR-1LE/1LJ/1ZE)
  • +0000521 = FN III 54 17" (PR-1ZT)
• Suspension:
  • +0000000 = Standard/Sport Suspension (PR-2UA)
  • +0000128 = Rough Road Suspension (PR-2UB)
• Engine:
  • +0010240 = Gasoline Engine (through 92 kW / 125 HP)
  • +0018432 = Gasoline Engine (from 92 kW / 125 HP) & All Diesel Engines

Notes: See production codes on car data plate. Coding is the sum of the individual options.

Basic Setting

Sensor for Steering Angle (G85)

Prerequisites:

• Start the vehicle.
• Turn the steering wheel one turn to the right and one turn to the left.
• Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.
• If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight.
• Ensure that the steering wheel is not moved again.
• Keep the engine running and do not switch off the ignition.
• System voltage at least 12.0 V.
  
  

[Select]
[03 - Brake Electronics]
[Coding-II - 11]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 060
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
To make sure the basic setting was succesful, check the sensor again.
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 1, the value has to be between -4.5 and +4.5 °.
[Done, Go Back]
[Close Controller, Go Back - 06]

Lateral Acceleration Sensor (G200)

Prerequisites:

• System voltage at least 12.0 V.
  
  

[Select]
[03 - Brake Electronics]
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 2, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Coding-II - 11]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 063
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
To make sure the basic setting was succesful, check the sensor again.
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 2, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Close Controller, Go Back - 06]

Brake Pressure Sensor 1 (G201)

Prerequisites:

• System voltage at least 12.0 V.
  
  

[Select]
[03 - Brake Electronics]
[Coding-II - 11]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 066
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
To make sure the basic setting was succesful, check the sensor again.
[Measuring Blocks - 08]
Group 005
[Go!]
Check field 1, the value has to be between -7.0 and +7.0 bar.
[Done, Go Back]
[Close Controller, Go Back - 06]

Longitudinal Acceleration Sensor (G251)

Prerequisites:

• System voltage at least 12.0 V.
  
  

[Select]
[03 - Brake Electronics]
[Coding-II - 11]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 069
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
To make sure the basic setting was succesful, check the sensor again.
[Measuring Blocks - 08]
Group 006
[Go!]
Check field 1, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Close Controller, Go Back - 06]

Special Procedures

System Function Test

See System Function Test