Difference between revisions of "6-Speed Direct Shift Gearbox (DSG/02E)"
RtWiKiSyS0p (talk | contribs) m |
|||
| Line 1: | Line 1: | ||
== Basic Setting == | == Basic Setting == | ||
| − | '''''NOTE:''' | + | '''''NOTE:''' Be sure to perform the following steps in the sequence shown, followed by the defined test drive.'' |
'''[Select]'''<br> | '''[Select]'''<br> | ||
| Line 16: | Line 16: | ||
=== Transmission Tolerances (Synch. Point. Measurement) === | === Transmission Tolerances (Synch. Point. Measurement) === | ||
| − | + | Group 060<br> | |
'''[Go!]'''<br> | '''[Go!]'''<br> | ||
Activate the Basic Setting.<br> | Activate the Basic Setting.<br> | ||
| Line 25: | Line 25: | ||
'''''Control Module Software Version < 0800:''''' | '''''Control Module Software Version < 0800:''''' | ||
| − | + | Group 062<br> | |
'''[Go!]'''<br> | '''[Go!]'''<br> | ||
Activate the Basic Setting.<br> | Activate the Basic Setting.<br> | ||
| Line 32: | Line 32: | ||
'''''Control Module Software Version >= 0800 :''''' | '''''Control Module Software Version >= 0800 :''''' | ||
| − | + | Group 067<br> | |
'''[Go!]'''<br> | '''[Go!]'''<br> | ||
Activate the Basic Setting.<br> | Activate the Basic Setting.<br> | ||
| Line 39: | Line 39: | ||
=== Reset Values (Clutch Safety Function) === | === Reset Values (Clutch Safety Function) === | ||
| − | + | Group 068<br> | |
'''[Go!]'''<br> | '''[Go!]'''<br> | ||
Activate the Basic Setting.<br> | Activate the Basic Setting.<br> | ||
| Line 46: | Line 46: | ||
=== Reset Values (Pressure Adaptation) === | === Reset Values (Pressure Adaptation) === | ||
| − | + | Group 065<br> | |
'''[Go!]'''<br> | '''[Go!]'''<br> | ||
Activate the Basic Setting.<br> | Activate the Basic Setting.<br> | ||
| Line 53: | Line 53: | ||
=== Reset Values (Steering Wheel Paddle Installation) === | === Reset Values (Steering Wheel Paddle Installation) === | ||
| − | + | Group 063<br> | |
'''[Go!]'''<br> | '''[Go!]'''<br> | ||
Activate the Basic Setting.<br> | Activate the Basic Setting.<br> | ||
| Line 60: | Line 60: | ||
=== Reset Values (ESP & Tip Cruise Control) === | === Reset Values (ESP & Tip Cruise Control) === | ||
| − | + | Group 069<br> | |
'''[Go!]'''<br> | '''[Go!]'''<br> | ||
Activate the Basic Setting.<br> | Activate the Basic Setting.<br> | ||
| Line 76: | Line 76: | ||
''Suggested test drive after replacing the mechatronic or successful basic setting.''<br><br> | ''Suggested test drive after replacing the mechatronic or successful basic setting.''<br><br> | ||
'''<u>Prerequisites:</u>'''<br> | '''<u>Prerequisites:</u>'''<br> | ||
| − | * ATF Temperature 30...100 °C (86...210 °F), see | + | * ATF Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019. |
| Line 83: | Line 83: | ||
The engine speed window for all gears is 1200 - 3500 RPM (for clutch calibration).<br> | The engine speed window for all gears is 1200 - 3500 RPM (for clutch calibration).<br> | ||
Perform one sharp braking followed by a full throttle acceleration (oil return check).<br> | Perform one sharp braking followed by a full throttle acceleration (oil return check).<br> | ||
| − | + | Evaluate creep and starting-off points.<br> | |
Check for leaks.<br> | Check for leaks.<br> | ||
| − | '''''NOTE:''' If the test drive cannot be performed in the recommended way or the necessary time, | + | '''''NOTE:''' If the test drive cannot be performed in the recommended way or the necessary time, any remaining adaptations will be performed automatically during normal driving.'' |
[[Category:Transmissions]] | [[Category:Transmissions]] | ||
Revision as of 15:44, 29 November 2006
Basic Setting
NOTE: Be sure to perform the following steps in the sequence shown, followed by the defined test drive.
[Select]
[02 - Transmission]
[Basic Settings - 04]
Transmission Tolerances (Enganged Calibration)
Block 061
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Transmission Tolerances (Synch. Point. Measurement)
Group 060
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Clutch Adaptation
Control Module Software Version < 0800:
Group 062
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Control Module Software Version >= 0800 :
Group 067
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (Clutch Safety Function)
Group 068
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (Pressure Adaptation)
Group 065
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (Steering Wheel Paddle Installation)
Group 063
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (ESP & Tip Cruise Control)
Group 069
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
[Done, Go Back]
[Fault Codes - 02]
Check and clear fault codes after successful test.
[Close Controller, Go Back - 06]
Perform the Defined Test Drive.
Special Procedures
Defined Test Drive
Suggested test drive after replacing the mechatronic or successful basic setting.
Prerequisites:
- ATF Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019.
Drive in Tiptronic Mode from stand still up to 6th Gear.
While doing that make sure to drive in Gears 3 or 5 for approx. 5 minutes and also in 4 or 6 for approx. 5 minutes.
The engine speed window for all gears is 1200 - 3500 RPM (for clutch calibration).
Perform one sharp braking followed by a full throttle acceleration (oil return check).
Evaluate creep and starting-off points.
Check for leaks.
NOTE: If the test drive cannot be performed in the recommended way or the necessary time, any remaining adaptations will be performed automatically during normal driving.