Difference between revisions of "VW Golf (1K) Comfort System"
From Ross-Tech Wiki
RtWiKiSyS0p (talk | contribs) |
|||
| Line 1: | Line 1: | ||
== Coding == | == Coding == | ||
| + | |||
| + | ''Coding information is found using the Long Coding Helper while connected to the vehicle with VCDS.'' | ||
| + | |||
| + | |||
== Adaptation == | == Adaptation == | ||
=== Channel 000: Remote Control Clearing === | === Channel 000: Remote Control Clearing === | ||
| − | ''' | + | * This Adaptation Channel is used to clear all matched Remote Controls. |
| − | ''' | + | |
| − | ''' | + | === Channel 001: Remote Control Matching === |
| − | + | ||
| − | ''' | + | * Start Matching new/additional Remote Controls with entering '''1''', then '''Test''' and '''Save''' the New Value. |
| − | + | * Press the '''Unlock''' button on each Remote Control you want to add, the Blinkers will light up to confirm the Adaptation Process of each Remote Control. | |
| − | ''' | + | |
| − | '''[ | + | '''''Note:''' The time for matching remotes after saving the new value should not exceed 15 seconds. You can add a maximum of 4 remotes. '''Remote Control for Cars equipped with Keyless Entry and Access are automatically being matched when [[VW Passat (3C) Immobilizer|Adapting the Immobilizer/Keys]].''''' |
| − | '' | + | |
| + | === Channel 003: Selective (Single) Door Locking === | ||
| + | * 0 = Selective Door Locking OFF | ||
| + | * 1 = Selective Door Locking ON | ||
| + | |||
| + | === Channel 004: Auto-Lock === | ||
| + | The Doors will lock automatically when the Vehicle reaches a Speed of 15 km/h or 10 mph. | ||
| + | * 0 = Auto-Lock OFF | ||
| + | * 1 = Auto-Lock ON | ||
| + | |||
| + | === Channel 005: Auto-Unlock === | ||
| + | The Doors will unlock automatically when the Key is removed from the Ignition Switch. | ||
| + | * 0 = Auto-Unlock OFF | ||
| + | * 1 = Auto-Unlock ON | ||
| + | === Channel 007: Unlocking Confirmation (Remote Control) === | ||
| + | Type of Confirmation when unlocking the Car via Remote Control. | ||
| + | * 0 = Confirmation OFF | ||
| + | * 1 = Confirmation via Blinker/Turn Signal | ||
| + | * 2 = Confirmation via Beep/Horn | ||
| + | * 3 = Confirmation via Beep/Horn & Blinker/Turn Signal | ||
| − | === Channel | + | === Channel 008: Unlocking Confirmation (Key Switch) === |
| + | Type of Confirmation when unlocking the Car via Key/Lock Switch. | ||
| + | * 0 = Confirmation OFF | ||
| + | * 1 = Confirmation via Blinker/Turn Signal | ||
| + | * 2 = Confirmation via Beep/Horn | ||
| + | * 3 = Confirmation via Beep/Horn & Blinker/Turn Signal | ||
| + | |||
| + | === Channel 010: Locking Confirmation (Remote Control) === | ||
| + | Type of Confirmation when locking the Car via Remote Control. | ||
| + | * 0 = Confirmation OFF | ||
| + | * 1 = Confirmation via Blinker/Turn Signal | ||
| + | * 2 = Confirmation via Beep/Horn | ||
| + | * 3 = Confirmation via Beep/Horn & Blinker/Turn Signal | ||
| + | |||
| + | === Channel 011: Locking Confirmation (Key Switch) === | ||
| + | Type of Confirmation when locking the Car via Key/Lock Switch. | ||
| + | * 0 = Confirmation OFF | ||
| + | * 1 = Confirmation via Blinker/Turn Signal | ||
| + | * 2 = Confirmation via Beep/Horn | ||
| + | * 3 = Confirmation via Beep/Horn & Blinker/Turn Signal | ||
| + | |||
| + | === Channel 012: Safe Confirmation === | ||
| + | Type of Confirmation when the car is being locked. | ||
| + | * 0 = Confirmation OFF | ||
| + | * 1 = Confirmation via Blinker/Turn Signal | ||
| + | * 2 = Confirmation via Beep/Horn | ||
| + | * 3 = Confirmation via Beep/Horn & Blinker/Turn Signal | ||
| − | + | === Channel 013: Alarm Horn Adjustment === | |
| − | + | The Alarm Horn Country Setting changes the Length and Volume of the Alarm Horn Sound. | |
| − | + | * 0 = Great Britain (Frequency Modulated - 10 Tamper Alarms) | |
| − | Channel | + | * 1 = Great Britain (Frequency Modulated - 1 Tamper Alarm) |
| − | + | * 2 = Rest of World (Discontinuous - 10 Tamper Alarms) | |
| − | + | * 3 = Rest of World (Discontinuous - 1 Tamper Alarm) | |
| − | * 0 = | ||
| − | * | ||
| + | === Channel 017: Comfort Function === | ||
| + | Enables Comfort via Remote Functionality depending on the Options enabled in the Control Module Coding. ''This Adaptation Channel will have no Effect if the Comfort Function(s) are disabled in the Control Module Coding.'' | ||
| − | * | + | * 0 = Comfort Function OFF |
| + | * 1 = Comfort Function ON | ||
| − | + | === Channel 018: Alarm Delay === | |
| − | + | Deactivates the Anti-Theft-Warning Delay when opening the Drivers Door before the Anti-Theft-Warning-System is being activated. | |
| − | |||
| − | |||
| − | + | * 0 = Alarm Delay OFF | |
| − | + | * 1 = Alarm Delay ON | |
| + | === Channel 019: Factory Mode === | ||
| + | Factory Mode is usually active when a newly delivered Control Module is being installed. To enable all Functions of the new Control Module Factory Mode has to be disabled. Once it has been disabled it cannot be enabled again. | ||
== Special Procedures == | == Special Procedures == | ||
| − | === Remote Control | + | === Remote Control Synchronization === |
* If locked, open the car using the drivers door lock. | * If locked, open the car using the drivers door lock. | ||
* Press the remote control ''unlock'' button. | * Press the remote control ''unlock'' button. | ||
| Line 45: | Line 95: | ||
* Switch off ignition and pull the key out of the ignition lock. | * Switch off ignition and pull the key out of the ignition lock. | ||
* Press the remote control ''lock'' or ''unlock'' button. | * Press the remote control ''lock'' or ''unlock'' button. | ||
| − | ''The | + | ''The synchronization is now finished.'' |
Revision as of 14:50, 15 March 2011
Coding
Coding information is found using the Long Coding Helper while connected to the vehicle with VCDS.
Adaptation
Channel 000: Remote Control Clearing
- This Adaptation Channel is used to clear all matched Remote Controls.
Channel 001: Remote Control Matching
- Start Matching new/additional Remote Controls with entering 1, then Test and Save the New Value.
- Press the Unlock button on each Remote Control you want to add, the Blinkers will light up to confirm the Adaptation Process of each Remote Control.
Note: The time for matching remotes after saving the new value should not exceed 15 seconds. You can add a maximum of 4 remotes. Remote Control for Cars equipped with Keyless Entry and Access are automatically being matched when Adapting the Immobilizer/Keys.
Channel 003: Selective (Single) Door Locking
- 0 = Selective Door Locking OFF
- 1 = Selective Door Locking ON
Channel 004: Auto-Lock
The Doors will lock automatically when the Vehicle reaches a Speed of 15 km/h or 10 mph.
- 0 = Auto-Lock OFF
- 1 = Auto-Lock ON
Channel 005: Auto-Unlock
The Doors will unlock automatically when the Key is removed from the Ignition Switch.
- 0 = Auto-Unlock OFF
- 1 = Auto-Unlock ON
Channel 007: Unlocking Confirmation (Remote Control)
Type of Confirmation when unlocking the Car via Remote Control.
- 0 = Confirmation OFF
- 1 = Confirmation via Blinker/Turn Signal
- 2 = Confirmation via Beep/Horn
- 3 = Confirmation via Beep/Horn & Blinker/Turn Signal
Channel 008: Unlocking Confirmation (Key Switch)
Type of Confirmation when unlocking the Car via Key/Lock Switch.
- 0 = Confirmation OFF
- 1 = Confirmation via Blinker/Turn Signal
- 2 = Confirmation via Beep/Horn
- 3 = Confirmation via Beep/Horn & Blinker/Turn Signal
Channel 010: Locking Confirmation (Remote Control)
Type of Confirmation when locking the Car via Remote Control.
- 0 = Confirmation OFF
- 1 = Confirmation via Blinker/Turn Signal
- 2 = Confirmation via Beep/Horn
- 3 = Confirmation via Beep/Horn & Blinker/Turn Signal
Channel 011: Locking Confirmation (Key Switch)
Type of Confirmation when locking the Car via Key/Lock Switch.
- 0 = Confirmation OFF
- 1 = Confirmation via Blinker/Turn Signal
- 2 = Confirmation via Beep/Horn
- 3 = Confirmation via Beep/Horn & Blinker/Turn Signal
Channel 012: Safe Confirmation
Type of Confirmation when the car is being locked.
- 0 = Confirmation OFF
- 1 = Confirmation via Blinker/Turn Signal
- 2 = Confirmation via Beep/Horn
- 3 = Confirmation via Beep/Horn & Blinker/Turn Signal
Channel 013: Alarm Horn Adjustment
The Alarm Horn Country Setting changes the Length and Volume of the Alarm Horn Sound.
- 0 = Great Britain (Frequency Modulated - 10 Tamper Alarms)
- 1 = Great Britain (Frequency Modulated - 1 Tamper Alarm)
- 2 = Rest of World (Discontinuous - 10 Tamper Alarms)
- 3 = Rest of World (Discontinuous - 1 Tamper Alarm)
Channel 017: Comfort Function
Enables Comfort via Remote Functionality depending on the Options enabled in the Control Module Coding. This Adaptation Channel will have no Effect if the Comfort Function(s) are disabled in the Control Module Coding.
- 0 = Comfort Function OFF
- 1 = Comfort Function ON
Channel 018: Alarm Delay
Deactivates the Anti-Theft-Warning Delay when opening the Drivers Door before the Anti-Theft-Warning-System is being activated.
- 0 = Alarm Delay OFF
- 1 = Alarm Delay ON
Channel 019: Factory Mode
Factory Mode is usually active when a newly delivered Control Module is being installed. To enable all Functions of the new Control Module Factory Mode has to be disabled. Once it has been disabled it cannot be enabled again.
Special Procedures
Remote Control Synchronization
- If locked, open the car using the drivers door lock.
- Press the remote control unlock button.
- Put the key in the ignition lock and switch on ignition.
- Switch off ignition and pull the key out of the ignition lock.
- Press the remote control lock or unlock button.
The synchronization is now finished.