Difference between revisions of "Trailer Hitch Retrofitting (4F)"
From Ross-Tech Wiki
RtWiKiSyS0p (talk | contribs) m |
RtWiKiSyS0p (talk | contribs) |
||
| Line 1: | Line 1: | ||
| − | + | ''These instructions may not cover mechanical/electronic details, they will only list the the diagnostic side (coding etc.). Additional details for the mechanical/electronic work needed are part of the retrofitting instructions provided by the parts supplier (i.e. trailer hitch retrofits) or can be found in the factory repair manuals and wiring diagrams.'' | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| + | == Installation & Wiring == | ||
| − | + | Information regarding the Installation can be found in the Repair Manuals, the Wiring Diagrams, the Parts Catalog and/or the Instructions included in the Retrofitting Kit. | |
| − | |||
| − | + | == Configuration == | |
| − | + | The following Activations are necessary to ensure that the newly fitted parts are properly recognized and are ready to use. | |
| − | ''''' | + | * '''Update the Installation List in the Gateway (J533 / #19).''' |
| + | ** Register the newly added '''69 - Trailer''' Control Module. | ||
| + | * '''Update the Trailer Control Module (J345 / #69) Coding.''' | ||
| + | ** Not all Retrofitting Kits contain Diagnostic capable Trailer Control Modules, some Aftermarket Modules may even be pre-coded. This Step can be ignored for Modules which are not Diagnostic capable. | ||
| + | ** ''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be used by the Long Coding Assistant once you access the Function using VCDS. If an Aftermarket Module is installed, check the Retrofitting Kit for further Instructions.'' | ||
| + | * '''Update the Engine Control Module (J623 / #01) Coding.''' | ||
| + | ** Make sure that the '''Engine is NOT running''', otherwise the new Coding will be rejected. Models equipped with Start/Stop System do have a Shutoff Switch/Button which will deactivate the Start/Stop Function. | ||
| + | ** For Engines with a 2nd Engine Control Module (J624 / #11) this needs to be coded as well. | ||
| + | ** As a Rule of Thumb, if the Engine Control Module uses a Short Coding the Activation is being done using Coding-II. If the Engine Control Module uses a Long Coding the Activation is done in (Long) Coding itself. Please also note that there are different Coding Variants for Long Coding. | ||
| + | ** ''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be used by the Long Coding Assistant once you access the Function using VCDS.'' | ||
| + | * '''Update the Level Control (J197 / #34) Coding, if installed.''' | ||
| + | ** ''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be shown once you access the Function using VCDS.'' | ||
| + | * '''Update the Parking Aid (J446 / #76) Coding, if installed.''' | ||
| + | ** ''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be shown once you access the Function using VCDS.'' | ||
| + | * '''Update the Rear View Camera (J772 / #6C) Coding, if installed.''' | ||
| + | ** ''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be displayed once you access the Coding Function using VCDS.'' | ||
| + | * '''Update the Lane Change Assist (J769 / #3C) Coding, if installed.''' | ||
| + | ** ''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be displayed once you access the Coding Function using VCDS.'' | ||
| + | * '''Update the Distance Regulation (J428 / #13) Coding, if installed.''' | ||
| + | ** ''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be displayed once you access the Coding Function using VCDS.'' | ||
| − | |||
| − | + | '''''If you are having trouble finding/calculating the proper Coding using the Long Coding Assist [http://ross-tech.com/contact.html please Contact us directly].''' Make sure to include a complete Diagnostic Protocol (Auto-Scan) from the Car and state which steps/work you have performed yet.'' | |
| − | + | __NOTOC__ | |
| − | |||
| − | ''''' | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Revision as of 09:25, 23 September 2011
These instructions may not cover mechanical/electronic details, they will only list the the diagnostic side (coding etc.). Additional details for the mechanical/electronic work needed are part of the retrofitting instructions provided by the parts supplier (i.e. trailer hitch retrofits) or can be found in the factory repair manuals and wiring diagrams.
Installation & Wiring
Information regarding the Installation can be found in the Repair Manuals, the Wiring Diagrams, the Parts Catalog and/or the Instructions included in the Retrofitting Kit.
Configuration
The following Activations are necessary to ensure that the newly fitted parts are properly recognized and are ready to use.
- Update the Installation List in the Gateway (J533 / #19).
- Register the newly added 69 - Trailer Control Module.
- Update the Trailer Control Module (J345 / #69) Coding.
- Not all Retrofitting Kits contain Diagnostic capable Trailer Control Modules, some Aftermarket Modules may even be pre-coded. This Step can be ignored for Modules which are not Diagnostic capable.
- Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be used by the Long Coding Assistant once you access the Function using VCDS. If an Aftermarket Module is installed, check the Retrofitting Kit for further Instructions.
- Update the Engine Control Module (J623 / #01) Coding.
- Make sure that the Engine is NOT running, otherwise the new Coding will be rejected. Models equipped with Start/Stop System do have a Shutoff Switch/Button which will deactivate the Start/Stop Function.
- For Engines with a 2nd Engine Control Module (J624 / #11) this needs to be coded as well.
- As a Rule of Thumb, if the Engine Control Module uses a Short Coding the Activation is being done using Coding-II. If the Engine Control Module uses a Long Coding the Activation is done in (Long) Coding itself. Please also note that there are different Coding Variants for Long Coding.
- Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be used by the Long Coding Assistant once you access the Function using VCDS.
- Update the Level Control (J197 / #34) Coding, if installed.
- Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be shown once you access the Function using VCDS.
- Update the Parking Aid (J446 / #76) Coding, if installed.
- Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be shown once you access the Function using VCDS.
- Update the Rear View Camera (J772 / #6C) Coding, if installed.
- Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be displayed once you access the Coding Function using VCDS.
- Update the Lane Change Assist (J769 / #3C) Coding, if installed.
- Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be displayed once you access the Coding Function using VCDS.
- Update the Distance Regulation (J428 / #13) Coding, if installed.
- Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be displayed once you access the Coding Function using VCDS.
If you are having trouble finding/calculating the proper Coding using the Long Coding Assist please Contact us directly. Make sure to include a complete Diagnostic Protocol (Auto-Scan) from the Car and state which steps/work you have performed yet.