Difference between revisions of "02844"
From Ross-Tech Wiki
RtWiKiSyS0p (talk | contribs) |
RtWiKiSyS0p (talk | contribs) |
||
| (3 intermediate revisions by 2 users not shown) | |||
| Line 10: | Line 10: | ||
==== Possible Causes ==== | ==== Possible Causes ==== | ||
| + | * Control Module incorrectly coded, Auto-Hold not installed | ||
| + | * Wiring/Connectors from/to Brake Light Switch (F) faulty | ||
* Wiring/Connectors from/to Lamp for Auto-Hold (K237) faulty | * Wiring/Connectors from/to Lamp for Auto-Hold (K237) faulty | ||
| − | |||
| − | |||
| − | |||
==== Possible Solutions ==== | ==== Possible Solutions ==== | ||
| − | * | + | * Perform Output Test |
* Check Control Module Coding | * Check Control Module Coding | ||
* Check Wiring/Connectors from/to Brake Light Switch (F) | * Check Wiring/Connectors from/to Brake Light Switch (F) | ||
| + | * Check Wiring/Connectors and fuse(s) from/to Lamp for Auto-Hold (K237) | ||
==== Special Notes ==== | ==== Special Notes ==== | ||
| − | * When found in [[VW Passat (3C) | + | * When found in [[VW Passat (3C)|VW Passat (3C)]]: [[VW Passat (3C) Parking Brake|Parking Brake]] |
| − | ** Check if Auto-Hold is installed, car data plate ''(sticker on 1st page of the service manual or identical sticker in the trunk)'' should have a '''UH2''' tag | + | ** Check if Auto-Hold is installed/equipped, car data plate ''(sticker on 1st page of the service manual or identical sticker in the trunk)'' should have a '''UH2''' tag and [[VW Passat (3C) Parking Brake#Coding|Parking Brake Control Module Coding]] accordingly. After Coding make sure to Cycle the Ignition and leave it OFF for at least 30 Seconds. |
| − | + | ** Check Brake Light Switch (F) Signal via Parking Brake Control Module Measuring Value Block (MVB) 003.1 | |
| − | ** Check Brake Light Switch (F) Signal via | + | ** Perform Selective Output Test (in Parking Brake Control Module) |
| − | |||
[[Category:Fault Codes]] | [[Category:Fault Codes]] | ||
Latest revision as of 09:24, 29 May 2012
02844 - Lamp for Automatic Parking Function
02844 - Lamp for Automatic Parking Function: Open or Short to Ground
Possible Symptoms
- Malfunction Indicator Light (MIL) active
Possible Causes
- Control Module incorrectly coded, Auto-Hold not installed
- Wiring/Connectors from/to Brake Light Switch (F) faulty
- Wiring/Connectors from/to Lamp for Auto-Hold (K237) faulty
Possible Solutions
- Perform Output Test
- Check Control Module Coding
- Check Wiring/Connectors from/to Brake Light Switch (F)
- Check Wiring/Connectors and fuse(s) from/to Lamp for Auto-Hold (K237)
Special Notes
- When found in VW Passat (3C): Parking Brake
- Check if Auto-Hold is installed/equipped, car data plate (sticker on 1st page of the service manual or identical sticker in the trunk) should have a UH2 tag and Parking Brake Control Module Coding accordingly. After Coding make sure to Cycle the Ignition and leave it OFF for at least 30 Seconds.
- Check Brake Light Switch (F) Signal via Parking Brake Control Module Measuring Value Block (MVB) 003.1
- Perform Selective Output Test (in Parking Brake Control Module)