Difference between revisions of "User talk:Jef"
From Ross-Tech Wiki
(Created page with "'''[Select]'''<br> '''[15 - Airbags]'''<br> '''[Security Access - 16]'''<br> Enter the code shown in the pop-up balloon to enable the basic setting.<br> '''[Do it!]'''<br> ''...") |
|||
| (9 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| + | This information applies to the MQB platform with the Steering Angle Sensor (G85) integrated into the Steering Assist (J500). This can be identified by evaluating the data in the Auto-Scan: | ||
| + | |||
| + | Address 44: Steering Assist (J500) Labels:| 5Q0-909-144.clb | ||
| + | Part No SW: 3Q0 909 144 K HW: 3Q0 909 144 H | ||
| + | Component: '''EPS_MQB_ZFLS''' 506 5072 | ||
| + | |||
| + | *If '''EPS_MQB_ZFLS''' is not shown in the Component field, this information may not apply. | ||
| + | |||
| + | == Basic Setting == | ||
| + | |||
| + | === Sensor for Steering Angle (G85) === | ||
| + | |||
| + | '''<u>Prerequisites:</u>'''<br> | ||
| + | * Start the vehicle.<br> | ||
| + | |||
| + | '''[44-Steering Assist]'''<br> | ||
| + | '''[Security Access - 16]'''<br> | ||
| + | *Enter 19249<br> | ||
| + | '''[Basic Settings - 04]'''<br> | ||
| + | *'''[MAS00815] Steering angle sensor'''<br> | ||
| + | '''[Go!]'''<br> | ||
| + | *Rotate steering wheel all the way to the left, hold firmly against end stop for 5 seconds.<br> | ||
| + | *Rotate steering wheel all the way to the right, hold firmly against end stop for 5 seconds.<br> | ||
| + | *Center steering wheel, front wheel straight ahead.<br> | ||
| + | '''[Stop]'''<br> | ||
| + | *Several error messages and warnings will appear on the cluster, what messages you get can vary based on how the vehicles is equipped.<br> | ||
| + | '''[Done, Go Back]'''<br> | ||
| + | *Rotate steering wheel all the way to the left, hold firmly against end stop for 5 seconds.<br> | ||
| + | *Rotate steering wheel all the way to the right, hold firmly against end stop for 5 seconds.<br> | ||
| + | *Center steering wheel, front wheel straight ahead.<br> | ||
| + | '''[Close Controller, Go Back - 06]'''<br> | ||
| + | *Cycle the ignition off for 10 seconds.<br> | ||
| + | <br> | ||
| + | '''Notes''' | ||
| + | *When doing the Basic Settings, should see the message of "Running", but it may not change to "Finished Correctly" | ||
| + | *Several control modules will flag DTCs, "Databus" type codes that can cleared out after the 10 second ignition cycle.<br> | ||
| + | |||
| + | == Video Link == | ||
| + | |||
| + | [[File:MBQ_G85_thumb_wiki.jpg|200px|link=https://www.youtube.com/watch?v=bXScTl4VvMc]] | ||
| + | |||
| + | https://www.youtube.com/watch?v=bXScTl4VvMc | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
'''[Select]'''<br> | '''[Select]'''<br> | ||
'''[15 - Airbags]'''<br> | '''[15 - Airbags]'''<br> | ||
| Line 19: | Line 74: | ||
** IDE03872-ENG99733,Seat occupied recognition imaginary part-Measured Value Capacitance | ** IDE03872-ENG99733,Seat occupied recognition imaginary part-Measured Value Capacitance | ||
** IDE03873-ENG99733,Seat occupied recognition compensated imaginary part-Measured Value Capacitance | ** IDE03873-ENG99733,Seat occupied recognition compensated imaginary part-Measured Value Capacitance | ||
| − | + | *** Not all systems have location IDE03873-ENG99733 | |
| + | It can be normal for one of those locations to be a value of 0 pF, but if two of those locations are 0 pF, it may be a sign of a failed pressure mat that needs to be replaced. | ||
* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan. | * We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan. | ||
Latest revision as of 17:11, 9 February 2024
This information applies to the MQB platform with the Steering Angle Sensor (G85) integrated into the Steering Assist (J500). This can be identified by evaluating the data in the Auto-Scan:
Address 44: Steering Assist (J500) Labels:| 5Q0-909-144.clb Part No SW: 3Q0 909 144 K HW: 3Q0 909 144 H Component: EPS_MQB_ZFLS 506 5072
- If EPS_MQB_ZFLS is not shown in the Component field, this information may not apply.
Basic Setting
Sensor for Steering Angle (G85)
Prerequisites:
- Start the vehicle.
[44-Steering Assist]
[Security Access - 16]
- Enter 19249
[Basic Settings - 04]
- [MAS00815] Steering angle sensor
[Go!]
- Rotate steering wheel all the way to the left, hold firmly against end stop for 5 seconds.
- Rotate steering wheel all the way to the right, hold firmly against end stop for 5 seconds.
- Center steering wheel, front wheel straight ahead.
[Stop]
- Several error messages and warnings will appear on the cluster, what messages you get can vary based on how the vehicles is equipped.
[Done, Go Back]
- Rotate steering wheel all the way to the left, hold firmly against end stop for 5 seconds.
- Rotate steering wheel all the way to the right, hold firmly against end stop for 5 seconds.
- Center steering wheel, front wheel straight ahead.
[Close Controller, Go Back - 06]
- Cycle the ignition off for 10 seconds.
Notes
- When doing the Basic Settings, should see the message of "Running", but it may not change to "Finished Correctly"
- Several control modules will flag DTCs, "Databus" type codes that can cleared out after the 10 second ignition cycle.
Video Link
https://www.youtube.com/watch?v=bXScTl4VvMc
[Select]
[15 - Airbags]
[Security Access - 16]
Enter the code shown in the pop-up balloon to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Select Resetting seat occupied recognition.
When applicable type the single digit 0 into the (reserved) box. If this is not present skip this step.
[Go!] to activate the Basic Setting.
After the result of Finished Correctly appears click [Stop]
The reset has been performed.
[Done, Go Back]
[Fault Codes - 02] Faults should NOT be stored
[Close Controller, Go Back - 06]
Notes
- If you get a "Request Sequence Error" when performing the Resetting seat occupied recognition then check the following Advance Measuring Values:
- IDE03871-ENG99733,Seat occupied recognition real part-Measured Value Capacitance
- IDE03872-ENG99733,Seat occupied recognition imaginary part-Measured Value Capacitance
- IDE03873-ENG99733,Seat occupied recognition compensated imaginary part-Measured Value Capacitance
- Not all systems have location IDE03873-ENG99733
It can be normal for one of those locations to be a value of 0 pF, but if two of those locations are 0 pF, it may be a sign of a failed pressure mat that needs to be replaced.
- We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.