|
|
| (12 intermediate revisions by 2 users not shown) |
| Line 1: |
Line 1: |
| | + | = WARNING: RESTRICTED ACCESS = |
| | | | |
| | + | Your attempt to access this page is considered UNAUTHORIZED! |
| | + | '''ERROR 401: UNAUTHORIZED''' |
| | | | |
| − | == Audi A5 (8T) Active/Dynamic Steering ==
| + | Your IP address has been logged. |
| − | | |
| − | == Coding ==
| |
| − | | |
| − | '''Coding for this Control Module is normally done via Software Version Management (SVM). If the old Control Module is still accessible read/copy it's Coding to the new Module.
| |
| − | | |
| − | | |
| − | | |
| − | == Basic Setting ==
| |
| − | | |
| − | === 1B-Active Steering ===
| |
| − | | |
| − | | |
| − | '''<u>Prerequisites:</u>'''<br>
| |
| − | * Battery Voltage = 12.0 - 14.0 V'''<br>
| |
| − | * No fault codes other than [[01087 | 01087 - Basic Setting Not Performed]]'''<br>
| |
| − | | |
| − | * Perform G85-Steering Angle Sensor Basic Settings found on this Ross-Tech wiki page: [[Audi A5 (8T) Steering Wheel Electronics#Basic Setting|Audi A4/A5 (8K/8T) Steering Angle Sensor (G85) Calibration]]
| |
| − | | |
| − | | |
| − |
| |
| − | | |
| − | | |
| − | <span style="color:#000000; background:#FFFF00"> '''- Continue Only after successfully completing the G85 basic settings -''' </span>
| |
| − | | |
| − | *Leave the steering wheel in the straight ahead position during the next steps.
| |
| − | | |
| − | | |
| − | '''[Select]'''<br>
| |
| − | '''[1B-Active Steering]'''<br>
| |
| − | | |
| − | '''[Security Access - 16]'''<br>
| |
| − | Enter 61378, to enable the basic setting.'''<br>
| |
| − | '''[Do it!]'''<br>
| |
| − | | |
| − | | |
| − | '''[Basic Settings - 04]'''<br>
| |
| − | Group 101<br>
| |
| − | '''[Go!]'''<br>
| |
| − | '''[ON/OFF/Next]''' <br>
| |
| − | | |
| − | * The results should be stored after a key cycle and fault code(s) should clear.
| |
| − | | |
| − | | |
| − | '''[Done, Go Back]''' <br>
| |
| − | '''[Fault Codes - 02]'''<br>
| |
| − | Check and clear fault codes.<br>
| |
| − | '''[Close Controller, Go Back - 06]'''<br>
| |
| − | | |
| − | | |
| − | | |
| − | | |
| − | | |
| − | | |
| − | | |
| − | | |
| − | | |
| − | ======================================================================
| |
| − | | |
| − | | |
| − | | |
| − | 001 Upper Limit Exceeded<br>
| |
| − | 002 Lower Specified Value too Low<br>
| |
| − | 003 Mechanical/Hydraulic Fault<br>
| |
| − | 004 No signal/communication<br>
| |
| − | 005 No or Incorrect Basic Settings/Adaptation<br>
| |
| − | 006 Short Circuit to positive<br>
| |
| − | 007 Short to Ground<br>
| |
| − | 008 Implausible Signal/Ranger or Performance<br>
| |
| − | 009 Open Circuit/short to ground<br>
| |
| − | 010 Open Circuit/short to positive<br>
| |
| − | 011 Open Circuit<br>
| |
| − | 012 Electrical fault in Circuit<br>
| |
| − | 013 Check/Read DTC memory<br>
| |
| − | 014 Defective<br>
| |
| − | 015<br>
| |
| − | 016 Signal outside of Tolerance<br>
| |
| − | | |
| − | <br>
| |
| − | | |
| − | 027 Implausible Signal<br>
| |
| − | 028 Short Circuit to positive<br>
| |
| − | 029 Short to Ground<br>
| |
| − | 030 Open Circuit<br>
| |
| − | 031 Open Circuit/short to ground<br>
| |
| − | 035 No Indication in Display<br>
| |
| − | 036 Open Circuit<br>
| |
| − | 037 Faulty<br>
| |
| − | 045 Connector<br>
| |
| − | 049 No Communications<br>
| |
| − | 079 Checking DTC Memory<br>
| |
| − | 194 Comparison not Carried Out<br>
| |
| − | | |
| − | | |
| − | | |
| − | | |
| − | | |
| − | | |
| − | | |
| − | | |
| − | | |
| − | | |
| − | | |
| − | | |
| − | | |
| − | __FORCETOC__
| |
| − | == 18613/P2181/008577 - Performance Malfunction in Cooling System ==
| |
| − | | |
| − | ==== Possible Causes ====
| |
| − | | |
| − | * Faulty Coolant Sensor
| |
| − | * Faulty Coolant Thermostat
| |
| − | * Faulty Wiring, Connections
| |
| − | | |
| − | ''Note'': This fault code sets when engine coolant temperature mapping falls out of expected range based on operating conditions of the engine.
| |
| − | * For example: Engine warms up, thermostat opens and stays open, coolant temperature drops below normal operating range. The ECM knows the coolant temperature should stay within 80.0...110.0 °C typically after warm up. Thus a drop in coolant temperature below normal operating temperature is not possible without a malfunction in cooling system.
| |
| − | | |
| − | | |
| − | | |
| − | | |
| − | ==== Possible Solutions ====
| |
| − | | |
| − | * Check G62 - Engine Coolant Temperature Sender <br>
| |
| − | ** Inspect wiring for G62 (Coolant Migration, damage, corrosion, etc)
| |
| − | | |
| − | * Check (if applicable) G83 - Radiator Outlet, Coolant Temperature Sender <br>
| |
| − | ** Inspect wiring for G83 (Coolant Migration, damage, corrosion, etc)
| |
| − | | |
| − | * Check Coolant Thermostat
| |
| − | ** Use Graph function in VCDS, Measuring Value Blocks - MVB
| |
| − | ** Start Engine cold, graph Coolant Temperature Sender (G62) Typically MVB Group-001
| |
| − | ** Hold RPM around 1,500rpm and watch coolant temp increase in Graph until thermostat opens, indicated by a slight drop in coolant temp
| |
| − | ** If coolant temp drops below minimum operating temperature (80°C) or never reaches operating temperature, (verified by external thermometer) suspect failed thermostat
| |
| − | | |
| − | * Vehicles with both G62-Engine Outlet, Coolant Temperature Sensor and G83-Radiator Outlet, Coolant Temperature Sensor
| |
| − | ** Use Measuring Value Block group MVB-130 instead on MVB-001
| |
| − | ** G62 should increase in Temperature before G83 increase when engine coolant is cold
| |
| − | ** G83 will increase when the thermostat opens and after G62 reaches operating temperature (80°C)
| |
| − | ** If G62 and G83 both increase while engine warms up, suspect failed thermostat
| |
| − | | |
| − | | |
| − | ==== Special Notes ====
| |
| − | | |
| − | * Check the stored Freeze Frame data with this fault code. Freeze Frame information will be found in the fault code description (if the module supports it) or in Generic OBD-II if the vehicle complies with those regulations.
| |
| − | ** Freeze Frame data stored at -40*C is generally an indication of a faulty ECT or wiring.
| |
| − | ** Freeze Frame data stored at +140*C is generally an indication of a faulty ECT or wiring.
| |
| − | ** Freeze Frame data stored with in the 68*C ~ 80*C range is an indication that the vehicle was close to, but not within, the cooling systems normal operation range. The Thermostat itself or Cooling system components may be at fault.
| |