Difference between revisions of "User:Jef"
| Line 40: | Line 40: | ||
<br> | <br> | ||
'''Prerequisites''' | '''Prerequisites''' | ||
| − | * Ignition | + | * Ignition ON, use a Battery maintainer |
* Vehicle on level surface | * Vehicle on level surface | ||
* No persons or gear in Vehicle | * No persons or gear in Vehicle | ||
| Line 52: | Line 52: | ||
* Enter 201013<br> | * Enter 201013<br> | ||
'''[Basic Settings - 04]'''<br> | '''[Basic Settings - 04]'''<br> | ||
| + | * '''[IDE03804] Deactivating loading mode'''<br> | ||
| + | '''[Go!]''' After the result of '''Finished Correctly''' appears click '''[Stop]'''<br> | ||
| + | * '''[IDE03751] Activate level control'''<br> | ||
| + | '''[Go!]''' After the result of '''Finished Correctly''' appears click '''[Stop]'''<br> | ||
| + | * '''[IDE03761] Delete calibration for level control''' | ||
| + | '''[Go!]''' After the result of '''Finished Correctly''' appears click '''[Stop]'''<br> | ||
| + | * '''[IDE03802] Set reference level''' | ||
| + | '''[Go!]''' After the result of '''Finished Correctly''' appears click '''[Stop]'''<br> | ||
Revision as of 10:27, 17 July 2024
As per Peter's suggestion, bundling Level Control information into wiki pages... looking to break this down into non UDS and UDS.
Page titles:
Level Control, UDS
Level Control, non-UDS
Looking at component info to help people ID or verify what version they have.
non-UDS (legacy):
Component: LUFTFDR.-CDC
Component: J197 LUFTFEDER
Component: - 2C1A1
UDS:
Component: LUFE-DAEMPFER
page title: Level Control, UDS
This information applies to Level Control, UDS versions. This can be identified by evaluating the data in the Auto-Scan:
Address 34: Level Control (J197) Labels:. 4G0-907-553.clb Part No SW: 4G0 907 553 G HW: 4G0 907 553 F Component: LUFE-DAEMPFER H19 0783
- If LUFE-DAEMPFER is not shown in the Component field, this information may not apply.
Re-adapt Adaptive Suspension to default position
Special Notes, warnings, etc
- Do not at any point in time select Basic Settings [IDE01475] Resetting of all adaptations.
- If you choose to do so, DTC B2013: No End-of-Line Programming will be stored and you will need to make an appointment with your local dealer!
- Make sure you perform and save an [Auto-Scan] before beginning any work.
- If there is an 'incorrectly coded' fault in the [34-Level Control], the controller will need to be coded first.
- If you are attempting to alter the ride height use this procedure at your own risk!
Prerequisites
- Ignition ON, use a Battery maintainer
- Vehicle on level surface
- No persons or gear in Vehicle
- Fuel Tank 60% or more
- Nothing under vehicle
- Doors are to remain shut during the entire procedure
- No faults in the [34-Level Control] controller other than "No or incorrect Basic Settings"
[34-Level Control]
[Security Access-16]
- Enter 201013
[Basic Settings - 04]
- [IDE03804] Deactivating loading mode
[Go!] After the result of Finished Correctly appears click [Stop]
- [IDE03751] Activate level control
[Go!] After the result of Finished Correctly appears click [Stop]
- [IDE03761] Delete calibration for level control
[Go!] After the result of Finished Correctly appears click [Stop]
- [IDE03802] Set reference level
[Go!] After the result of Finished Correctly appears click [Stop]