Difference between revisions of "User:Jef"
| Line 36: | Line 36: | ||
** If you choose to do so, [http://wiki.ross-tech.com/wiki/index.php/B2013 DTC B2013: No End-of-Line Programming] will be stored and you will need to make an appointment with your local dealer! | ** If you choose to do so, [http://wiki.ross-tech.com/wiki/index.php/B2013 DTC B2013: No End-of-Line Programming] will be stored and you will need to make an appointment with your local dealer! | ||
* Make sure you perform and save an [https://www.ross-tech.com/vcds/tour/autoscan.php '''Auto-Scan'''] before beginning any work. | * Make sure you perform and save an [https://www.ross-tech.com/vcds/tour/autoscan.php '''Auto-Scan'''] before beginning any work. | ||
| − | * If there is an 'incorrectly coded' fault in the [34-Level Control], the controller will need to be coded first. | + | * If there is an 'incorrectly coded' fault in the '''[34-Level Control]''', the controller will need to be coded first. |
*If you are attempting to alter the ride height use this procedure at your own risk! | *If you are attempting to alter the ride height use this procedure at your own risk! | ||
<br> | <br> | ||
| Line 46: | Line 46: | ||
* Nothing under vehicle | * Nothing under vehicle | ||
* Doors are to remain shut during the entire procedure | * Doors are to remain shut during the entire procedure | ||
| − | * No faults in the [34-Level Control] controller other than "No or incorrect Basic Settings" | + | * No faults in the '''[34-Level Control]''' controller other than "No or incorrect Basic Settings" |
<br> | <br> | ||
'''[34-Level Control]'''<br> | '''[34-Level Control]'''<br> | ||
| Line 75: | Line 75: | ||
'''[Go Back]'''<br> | '''[Go Back]'''<br> | ||
<br> | <br> | ||
| − | |||
Measure the ride height, in millimeters, from the center of the wheel to the edge of fender, do this for all four wheels and record the values.<br> | Measure the ride height, in millimeters, from the center of the wheel to the edge of fender, do this for all four wheels and record the values.<br> | ||
Revision as of 11:12, 17 July 2024
As per Peter's suggestion, bundling Level Control information into wiki pages... looking to break this down into non UDS and UDS.
Page titles:
Level Control, UDS
Level Control, non-UDS
Looking at component info to help people ID or verify what version they have.
non-UDS (legacy):
Component: LUFTFDR.-CDC
Component: J197 LUFTFEDER
Component: - 2C1A1
UDS:
Component: LUFE-DAEMPFER
page title: Level Control, UDS
This information applies to Level Control, UDS versions. This can be identified by evaluating the data in the Auto-Scan:
Address 34: Level Control (J197) Labels:. 4G0-907-553.clb Part No SW: 4G0 907 553 G HW: 4G0 907 553 F Component: LUFE-DAEMPFER H19 0783
- If LUFE-DAEMPFER is not shown in the Component field, this information may not apply.
Re-adapt Adaptive Suspension to default position
Special Notes, warnings, etc
- Do not at any point in time select Basic Settings [IDE01475] Resetting of all adaptations.
- If you choose to do so, DTC B2013: No End-of-Line Programming will be stored and you will need to make an appointment with your local dealer!
- Make sure you perform and save an Auto-Scan before beginning any work.
- If there is an 'incorrectly coded' fault in the [34-Level Control], the controller will need to be coded first.
- If you are attempting to alter the ride height use this procedure at your own risk!
Prerequisites
- Ignition on, engine off. Use a Battery maintainer!!
- Vehicle on level surface
- No persons or gear in Vehicle
- Fuel Tank 60% or more
- Nothing under vehicle
- Doors are to remain shut during the entire procedure
- No faults in the [34-Level Control] controller other than "No or incorrect Basic Settings"
[34-Level Control]
[Security Access-16]
- Enter 201013
[Basic Settings - 04]
- [IDE03804] Deactivating loading mode
[Go!] After the result of Finished Correctly appears click [Stop]
- [IDE03751] Activate level control
[Go!] After the result of Finished Correctly appears click [Stop]
- [IDE03761] Delete calibration for level control
[Go!] After the result of Finished Correctly appears click [Stop]
- [IDE03802] Set reference level
- Vehicle should level itself during this step, may take some time.
[Go!] After the result of Finished Correctly appears click [Stop]
[Go Back]
[Basic Settings - 04]
- For each Basic Setting, click [Go!] After the result of Finished Correctly appears click [Stop]
- Select the Basic Setting steps from the drop down menu in the order shown!!
- [IDE03804] Deactivating loading mode
- [IDE03751] Activate level control
- [IDE03761] Delete calibration for level control
- [IDE03802] Set reference level
- Vehicle should level itself during this step, may take some time.
- [IDE03804] Deactivating loading mode
[Go Back]
Measure the ride height, in millimeters, from the center of the wheel to the edge of fender, do this for all four wheels and record the values.
[Adaptation - 10]
- Choose from the drop down menu and enter the "New value" recorded value for each of the wheels below, then press [Do it!]
- [IDE02001] Body height left front wheel house edge
- [IDE02002] Body height right front wheel house edge
- [IDE02003] Body height left rear wheel house edge
- [IDE02004] Body height right rear wheel house edge
[Go Back]
[Basic Settings - 04]
- For each Basic Setting, click [Go!] After the result of Finished Correctly appears click [Stop]
- Select the Basic Setting steps from the drop down menu in the order shown!!
- [IDE03762] Calibrate level control
- [IDE03751] Activate level control
[Go Back]