User:Jef

As per Peter's suggestion, bundling Level Control information into wiki pages... looking to break this down into non UDS and UDS.

Page titles:
Level Control, UDS
Level Control, non-UDS

Looking at component info to help people ID or verify what version they have.

non-UDS (legacy):
Component: LUFTFDR.-CDC
Component: J197 LUFTFEDER
Component: - 2C1A1

UDS:
Component: LUFE-DAEMPFER

page title: Level Control, UDS

---

This information applies to Level Control, UDS versions. This can be identified by evaluating the data in the Auto-Scan:

Address 34: Level Control (J197)       Labels:. 4G0-907-553.clb
   Part No SW: 4G0 907 553 G    HW: 4G0 907 553 F
   Component: LUFE-DAEMPFER H19 0783

• If LUFE-DAEMPFER is not shown in the Component field, this information may not apply.

---

Re-adapt Adaptive Suspension to default position

Special Notes, warnings, etc

• Do not at any point in time select Basic Settings [IDE01475] Resetting of all adaptations.
  • If you choose to do so, DTC B2013: No End-of-Line Programming will be stored and you will need to make an appointment with your local dealer!
• Make sure you perform and save an Auto-Scan before beginning any work.
• If there is an 'incorrectly coded' fault in the [34-Level Control], the controller will need to be coded first.
• If you are attempting to alter the ride height use this procedure at your own risk!

Prerequisites

• Ignition on, engine off. Use a Battery maintainer!!
• Vehicle on level surface
• No persons or gear in Vehicle
• Fuel Tank 60% or more
• Nothing under vehicle
• Doors are to remain shut during the entire procedure
• No faults in the [34-Level Control] controller other than "No or incorrect Basic Settings"

[34-Level Control]
[Security Access-16]

• Enter 201013
  

[Basic Settings - 04]

• [IDE03804] Deactivating loading mode
  

[Go!] After the result of Finished Correctly appears click [Stop]

• [IDE03751] Activate level control
  

[Go!] After the result of Finished Correctly appears click [Stop]

• [IDE03761] Delete calibration for level control

[Go!] After the result of Finished Correctly appears click [Stop]

• [IDE03802] Set reference level
  • Vehicle should level itself during this step, may take some time.

[Go!] After the result of Finished Correctly appears click [Stop]
[Go Back]

[Basic Settings - 04]

• For each Basic Setting, click [Go!] After the result of Finished Correctly appears click [Stop]
• Select the Basic Setting steps from the drop down menu in the order shown!!
  • [IDE03804] Deactivating loading mode
    
  • [IDE03751] Activate level control
    
  • [IDE03761] Delete calibration for level control
  • [IDE03802] Set reference level
    • Vehicle should level itself during this step, may take some time.

[Go Back]

Measure the ride height, in millimeters, from the center of the wheel to the edge of fender, do this for all four wheels and record the values.

[Adaptation - 10]

• Choose from the drop down menu and enter the "New value" recorded value for each of the wheels below, then press [Do it!]
  • [IDE02001] Body height left front wheel house edge
  • [IDE02002] Body height right front wheel house edge
  • [IDE02003] Body height left rear wheel house edge
  • [IDE02004] Body height right rear wheel house edge

[Go Back]

[Basic Settings - 04]

• For each Basic Setting, click [Go!] After the result of Finished Correctly appears click [Stop]
• Select the Basic Setting steps from the drop down menu in the order shown!!
  • [IDE03762] Calibrate level control
  • [IDE03751] Activate level control

[Go Back]

Notes

• This information is from DrPeter's forum post.
• OE Ride Height information can be found on the forum post.
  • https://forums.ross-tech.com/index.php?threads/12737/