Difference between revisions of "User:Jef"

From Ross-Tech Wiki
Line 1: Line 1:
 
As per Peter's suggestion, bundling Level Control information into wiki pages... looking to break this down into non UDS and UDS.
 
As per Peter's suggestion, bundling Level Control information into wiki pages... looking to break this down into non UDS and UDS.
  
−
Page titles:<br>
 
−
Level Control, UDS<br>
 
−
Level Control, non-UDS<br>
 
−
 
−
 
−
Looking at component info to help people ID or verify what version they have.
 
  
 
<br>
 
<br>
Line 15: Line 9:
  
  
−
UDS:<br>
 
−
Component: LUFE-DAEMPFER<br>
 
  
  
 +
== Bleeding or Charging ==
 +
Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk. As always, you should refer to a Factory Repair Manual for your vehicle!
  
−
page title: Level Control, UDS (LUFE-DAEMPFER)
+
'''<u>Prerequisites:</u>'''<br>
−
----
+
*Doors, hood and rear lid closed
−
This information applies to Level Control, [https://forums.ross-tech.com/index.php?threads/1905/ UDS versions].  This can be identified by evaluating the data in the Auto-Scan:
+
*Engine at idle
  
−
Address 34: Level Control (J197)      Labels:. 4G0-907-553.clb
+
Note: The bleeding procedure will lower the vehicle, proceed with caution and refer to the factory repair manual for proper repair information, warnings and cautions!
−
    Part No SW: 4G0 907 553 G    HW: 4G0 907 553 F
 
−
    Component: '''LUFE-DAEMPFER''' H19 0783
 
  
−
Address 34: Level Control (J197)      Labels:. 4G0-907-553.clb
+
'''[Select]'''<br>
−
    Part No SW: 4G0 907 553 G    HW: 4G0 907 553 F
 
−
    Component: '''LUFE-DAEMPFER''' H19 0783
 
−
    Coding: 008000
 
−
    Shop #: WSC 12345 123 12345
 
−
    ASAM Dataset: EV_AirSuspe 003025
 
−
 
 
−
*If '''LUFE-DAEMPFER''' is not shown in the Component field, this information may not apply.
 
−
 
 
−
<br>
 
−
==Re-adapt Adaptive Suspension to default position==
 
−
'''Special Notes, warnings, etc'''
 
−
* '''Do not''' at any point in time select Basic Settings '''[IDE01475] Resetting of all adaptations'''.
 
−
** If you choose to do so, [http://wiki.ross-tech.com/wiki/index.php/B2013 DTC B2013: No End-of-Line Programming] will be stored and you will need to make an appointment with your local dealer!
 
−
* Make sure you perform and save an [https://www.ross-tech.com/vcds/tour/autoscan.php '''Auto-Scan'''] before beginning any work.
 
−
* If there is an 'incorrectly coded' fault in the '''[34-Level Control]''', the controller will need to be coded first.
 
−
*If you are attempting to alter the ride height use this procedure at your own risk!
 
−
<br>
 
−
'''Prerequisites'''
 
−
* Ignition on, engine off.  Use a Battery maintainer!!
 
−
* Vehicle on level surface
 
−
* No persons or gear in Vehicle
 
−
* Fuel Tank 60% or more
 
−
* Nothing under vehicle
 
−
* Doors are to remain shut during the entire procedure
 
−
* No faults in the '''[34-Level Control]''' controller other than "No or incorrect Basic Settings"
 
−
<br>
 
 
'''[34-Level Control]'''<br>
 
'''[34-Level Control]'''<br>
 
'''[Security Access-16]'''<br>
 
'''[Security Access-16]'''<br>
−
* Enter 201013<br>
+
Enter 08367
−
'''[Basic Settings - 04]'''<br>
+
* If the Security Access code does not work, try 08367 in '''[Login - 11]''' or '''[Coding II - 11]'''
−
* '''[IDE03804] Deactivating loading mode'''<br>
 
−
'''[Go!]'''  After the result of '''Finished Correctly''' appears click '''[Stop]'''<br>
 
−
* '''[IDE03751] Activate level control'''<br>
 
−
'''[Go!]'''  After the result of '''Finished Correctly''' appears click '''[Stop]'''<br>
 
−
* '''[IDE03761] Delete calibration for level control'''
 
−
'''[Go!]'''  After the result of '''Finished Correctly''' appears click '''[Stop]'''<br>
 
−
* '''[IDE03802] Set reference level'''
 
−
** Vehicle should level itself during this step, may take some time.
 
−
'''[Go!]''' After the result of '''Finished Correctly''' appears click '''[Stop]'''<br>
 
−
'''[Go Back]'''<br>
 
−
<br>
 
  
−
'''[Basic Settings - 04]'''<br>
+
'''[Basic Settings-04]'''<br>
−
* For each Basic Setting, click '''[Go!]'''  After the result of '''Finished Correctly''' appears click '''[Stop]'''
+
* Bleeding:
−
* Select the Basic Setting steps from the drop down menu in the order shown!!
+
** Group 020 = to Bleed Pressure Accumulator<br>
−
** '''[IDE03804] Deactivating loading mode'''<br>
+
** Group 021 = to Bleed Front Axle<br>
−
** '''[IDE03751] Activate level control'''<br>
+
** Group 022 = to Bleed Rear Axle<br>
−
** '''[IDE03761] Delete calibration for level control'''
+
* Charging:
−
** '''[IDE03802] Set reference level'''
+
** Group 023 = to Charge Pressure Accumulator
−
*** Vehicle should level itself during this step, may take some time.
+
** Group 024 = to Charge Front Axle
 +
** Group 025 = to Charge Rear Axle
 +
'''[Go!]'''<br>
 +
'''[ON/OFF/Next]'''<br>
  
−
'''[Go Back]'''<br>
+
Field-4 will display the current pressure.<br>
−
<br>
+
The procedure will time out after 60 seconds.<br>
−
 
+
The procedure maybe repeated as necessary to achieve the desired system pressure.
−
Measure the ride height, in millimeters, from the center of the wheel to the edge of fender, do this for all four wheels and record the values.<br>
 
−
https://www.ross-tech.com/vag-com/cars/images/rim.jpeg
 
−
 
 
−
<br>
 
−
'''[Adaptation - 10]'''
 
−
* Choose from the drop down menu and enter the "New value" recorded value for each of the wheels below, then press '''[Do it!]'''
 
−
** '''[IDE02001] Body height left front wheel house edge'''
 
−
** '''[IDE02002] Body height right front wheel house edge'''
 
−
** '''[IDE02003] Body height left rear wheel house edge'''
 
−
** '''[IDE02004] Body height right rear wheel house edge'''
 
−
'''[Go Back]'''<br>
 
−
 
 
−
'''[Basic Settings - 04]'''<br>
 
−
* For each Basic Setting, click '''[Go!]'''  After the result of '''Finished Correctly''' appears click '''[Stop]'''
 
−
* Select the Basic Setting steps from the drop down menu in the order shown!!
 
−
** '''[IDE03762] Calibrate level control'''
 
−
** '''[IDE03751] Activate level control'''
 
−
'''[Go Back]'''<br>
 
−
<br>
 
−
'''Notes'''
 
−
* This information is from DrPeter's forum post.
 
−
* OE Ride Height information can be found on the forum post.
 
−
**  https://forums.ross-tech.com/index.php?threads/12737/
 
−
<br>
 
−
<!--
 
−
==Bleeding and Charging==
 
−
very much draft info, make sure formatting looks good.<br>
 
−
 
 
−
'''Prerequisites'''
 
−
* Engine at idle
 
−
* Doors are to remain shut during the entire procedure
 
−
'''[34-Level Control]'''<br>
 
−
'''[Security Access-16]'''<br>
 
−
* Enter 201013<br>
 
−
'''[Basic Settings - 04]'''<br>
 
−
* [IDE03753] Venting pressure reservoir
 
−
* [IDE03754] Vent air shock absorbers for front axle
 
−
* [IDE03755] Vent air shock absorbers for rear axle
 
−
* [IDE03756] Fill pressure reservoir
 
−
* [IDE03757] Fill air shock absorbers for front axle
 
−
* [IDE03758] Fill air shock absorbers for rear axle
 
−
* [IDE03759] Fill left rear air shock absorber
 
−
* [IDE03760] Fill right rear air shock absorber
 
−
<br>
 
  
  
 +
==== Special Notes ====
  
−
Live data that may be useful:
+
*These instructions should work with most non-UDS Level Control systems found in:
−
* [IDE02951] Absolute left front vehicle height
+
**A6
−
* [IDE02952] Absolute right front vehicle height
+
**A8
−
* [IDE02953] Absolute left rear vehicle height
+
**Q7
−
* [IDE02954] Absolute right rear vehicle height
+
**Phaeton
−
* [IDE02940] System pressure
+
**Touareg
−
* [IDE03064] Accumulator pressure
+
**Bentley Continental.
−
-->
+
*http://forums.ross-tech.com/showthread.php?1996-Level-Control-Bleeding-Charging

Revision as of 14:38, 17 July 2024

As per Peter's suggestion, bundling Level Control information into wiki pages... looking to break this down into non UDS and UDS.



non-UDS (legacy):
Component: LUFTFDR.-CDC
Component: J197 LUFTFEDER
Component: - 2C1A1



Bleeding or Charging

Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk. As always, you should refer to a Factory Repair Manual for your vehicle!

Prerequisites:

  • Doors, hood and rear lid closed
  • Engine at idle

Note: The bleeding procedure will lower the vehicle, proceed with caution and refer to the factory repair manual for proper repair information, warnings and cautions!

[Select]
[34-Level Control]
[Security Access-16]
Enter 08367

  • If the Security Access code does not work, try 08367 in [Login - 11] or [Coding II - 11]

[Basic Settings-04]

  • Bleeding:
    • Group 020 = to Bleed Pressure Accumulator
    • Group 021 = to Bleed Front Axle
    • Group 022 = to Bleed Rear Axle
  • Charging:
    • Group 023 = to Charge Pressure Accumulator
    • Group 024 = to Charge Front Axle
    • Group 025 = to Charge Rear Axle

[Go!]
[ON/OFF/Next]

Field-4 will display the current pressure.
The procedure will time out after 60 seconds.
The procedure maybe repeated as necessary to achieve the desired system pressure.


Special Notes

Retrieved from "http://wiki.ross-tech.com/wiki/index.php?title=User:Jef&oldid=9558"