|
|
| (21 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| − | Page Title = Level Control, non UDS
| + | == Contacting Ross-Tech == |
| | | | |
| − | This information applies to the [https://forums.ross-tech.com/index.php?threads/1905/ non UDS] Level Control. This can be identified by evaluating the data in the Auto-Scan:
| + | Blah blah blah, if additional assistance is needed, our registered customers can submit an auto-scan for review blah blah blah |
| | | | |
| − | Address 34: Level Control Labels: 4E0-910-553.clb
| + | Once the Auto-Scan is complete, click on the small VCDS icon in the top left corner, then select '''[Copy and Submit Auto-Scan]'''. |
| − | Part No SW: 4E0 910 553 K HW: 4E0 907 553 H
| |
| − | Component: '''LUFTFDR.-CDC''' H07 4590
| |
| | | | |
| − | Address 34: Level Control Labels: 4F0-910-553.clb
| + | https://i.imgur.com/XbVYS1j.jpg |
| − | Part No SW: 4F0 910 553 A HW: 4F0 907 553 A
| |
| − | Component: '''J197 LUFTFEDER''' H17 0060
| |
| | | | |
| − | *If '''LUFTFDR.-CDC''' or '''J197 LUFTFEDER''' is not shown in the Component field, this information may not apply.
| |
| | | | |
| − | ==Suspension Level Control Calibration==
| + | This will load up a special web page with a form to fill out. Please verify you type in your correct email address. |
| − | '''Prerequisites'''
| |
| − | * Engine at idle
| |
| − | * Transmission in park/neutral
| |
| − | * Doors, hood, rear lid or hatch are to remain shut during the entire procedure
| |
| | | | |
| − | '''[Select]'''<br>
| + | The Short Serial Number is on your Ross-Tech device, you will find that on the sticker. It might be something like: |
| − | '''[34 - Level Control]'''<br>
| + | * HN2-xxxxxx |
| − | '''[Security Access - 16]'''<br>
| + | * H17-xxxxxx |
| − | * Enter 31564 | + | * HCxxxxxx |
| − | '''[Do It!]'''<br>
| + | * UCxxxxxx |
| − | '''[Adaption - 10]'''<br>
| |
| − | * Channel 01 | |
| − | '''[Read]'''<br>
| |
| | | | |
| − | The vehicle will now try to level itself. The first field will show "Wait". Once this process is complete, the first field will show "Value".<br>
| + | In the Comments box, document the issue or concern. Once you have that typed out, in the Comment box, right click your mouse and then select '''[Paste]'''. |
| − | Now measure the ride height, in millimeters, from the center of the wheel to the edge of fender, do this for all four wheels and record the values.<br>
| |
| − | https://www.ross-tech.com/vag-com/cars/images/rim.jpeg
| |
| | | | |
| − | <br>
| + | https://i.imgur.com/OJLxxx8.jpeg |
| | | | |
| − | In the "New Value" field for '''channel 01''', input the measurement from the '''left front''' wheel.<br>
| + | https://i.imgur.com/5Wc30hQ.jpeg |
| − | '''[Test]''' - '''[Save]''' - Confirm '''[Yes]'''<br>
| |
| − | Click the '''[Up]''' button to go to Channel 02.<br>
| |
| | | | |
| | + | You should see the data from the Auto-Scan populate the Comments field after you paste. |
| | | | |
| − | In the "New Value" field for '''channel 02''', input the measurement from the '''right front''' wheel.<br>
| + | Click the '''[Send Email!]''' that is below the Comments box once the form is filled out. |
| − | '''[Test]''' - '''[Save]''' - Confirm '''[Yes]'''<br> | |
| − | Click the '''[Up]''' button to go to Channel 03.<br>
| |
| | | | |
| | + | The Ross-Tech support team will reply back once we have an answer to provide. We also have a Ross-Tech Forum where you should post your scan and questions: |
| | | | |
| − | In the "New Value" field for '''channel 03''', input the measurement from the '''left rear wheel'''.<br>
| + | '''https://forums.ross-tech.com/index.php''' |
| − | '''[Test]''' - '''[Save]''' - Confirm '''[Yes]'''<br>
| |
| − | Click the '''[Up]''' button to go to Channel 04.<br>
| |
| | | | |
| − | | + | That is the best place to get help from the greatest variety of different people, in a place where answers will be searchable in the future as well. |
| − | In the "New Value" field for '''channel 04''', input the measurement from the '''right rear wheel'''.<br>
| |
| − | '''[Test]''' - '''[Save]''' - Confirm '''[Yes]'''<br>
| |
| − | Click the '''[Up]''' button to go to Channel 05.<br>
| |
| − | | |
| − | | |
| − | In the "New Value" field for '''channel 05''', input a value of '''1'''.<br>
| |
| − | '''[Test]''' - '''[Save]''' - Confirm '''[Yes]'''<br>
| |
| − | | |
| − | '''[Done, Go Back]'''<br>
| |
| − | | |
| − | Check for fault codes, if all procedures went fine there should be none.<br>
| |
| − | | |
| − | ===Special Notes===
| |
| − | * In Adaptation channel 01, from "Wait" to "Value" should take less than 5 minutes.
| |
| − | ** If you still have the "wait" message after 5 minutes you could have a small leak or a weak pump.
| |
| − | * If you run into issues, verify the level sensors are to factory design.
| |
| − | ** Damaged or improperly installed hardware for the level sensors will confuse the system.
| |
| − | ** Verify the terminals and wiring for the level sensors are clean.
| |
| − | | |
| − | ===Ride Height Factory Values===
| |
| − | * After a successful Suspension Level Control Calibration, the approximate values should be:
| |
| − | ** Audi A6 (4F) (PR-1BK): 386 mm (front) and 384 mm (rear)
| |
| − | ** Audi A6 (4F) Allroad (PR-1BY): 388 mm (front) and 380 mm (rear)
| |
| − | ** Audi A8 (4E) standard suspension (PR-1BK): 416 mm (front) and 398 mm (rear)
| |
| − | ** Audi A8/S8 (4E) sport suspension (PR-2MA/2MB): 396 mm (front) and 378 mm (rear)
| |
| − | ** Audi Q7 (4L): 449 mm (front) and 465 mm (rear)
| |
| − | ** VW Phaeton (3D) RoW (Rest of World): 407 mm (front) and 401 mm (rear)
| |
| − | ** VW Phaeton (3D) NAR (North American Region): 417 mm (front) and 411 (rear)
| |
| − | ** VW Touareg (7L) standard: 497 mm (front) and 502 mm (rear)
| |
| − | ** VW Touareg (7L) offroad: 488 mm (front) and 498 mm (rear)
| |
| − | | |
| − | <br>
| |
| − | == Bleeding or Charging ==
| |
| − | Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk. As always, you should refer to a Factory Repair Manual for your vehicle!
| |
| − | | |
| − | '''<u>Prerequisites:</u>'''<br>
| |
| − | *Doors, hood and rear lid closed
| |
| − | *Engine at idle
| |
| − | | |
| − | Note: The bleeding procedure will lower the vehicle, proceed with caution and refer to the factory repair manual for proper repair information, warnings and cautions!
| |
| − | | |
| − | '''[Select]'''<br>
| |
| − | '''[34-Level Control]'''<br>
| |
| − | '''[Security Access-16]'''<br>
| |
| − | Enter 08367
| |
| − | * If the Security Access code does not work, try 08367 in '''[Coding II - 11]'''
| |
| − | | |
| − | '''[Basic Settings-04]'''<br>
| |
| − | * Bleeding:
| |
| − | ** Group 020 = to Bleed Pressure Accumulator<br>
| |
| − | ** Group 021 = to Bleed Front Axle<br>
| |
| − | ** Group 022 = to Bleed Rear Axle<br>
| |
| − | * Charging:
| |
| − | ** Group 023 = to Charge Pressure Accumulator
| |
| − | ** Group 024 = to Charge Front Axle
| |
| − | ** Group 025 = to Charge Rear Axle
| |
| − | '''[Go!]'''<br>
| |
| − | '''[ON/OFF/Next]'''<br>
| |
| − | | |
| − | Field-4 will display the current pressure.<br>
| |
| − | The procedure will time out after 60 seconds.<br>
| |
| − | The procedure maybe repeated as necessary to achieve the desired system pressure.
| |
| − | | |
| − | | |
| − | ==== Special Notes ====
| |
| − | | |
| − | *These instructions should work with most non-UDS Level Control systems found in:
| |
| − | **A6
| |
| − | **A8
| |
| − | **Q7
| |
| − | **Phaeton
| |
| − | **Touareg
| |
| − | **Bentley Continental.
| |
| − | *http://forums.ross-tech.com/showthread.php?1996-Level-Control-Bleeding-Charging
| |
Contacting Ross-Tech
Blah blah blah, if additional assistance is needed, our registered customers can submit an auto-scan for review blah blah blah
Once the Auto-Scan is complete, click on the small VCDS icon in the top left corner, then select [Copy and Submit Auto-Scan].
This will load up a special web page with a form to fill out. Please verify you type in your correct email address.
The Short Serial Number is on your Ross-Tech device, you will find that on the sticker. It might be something like:
- HN2-xxxxxx
- H17-xxxxxx
- HCxxxxxx
- UCxxxxxx
In the Comments box, document the issue or concern. Once you have that typed out, in the Comment box, right click your mouse and then select [Paste].
You should see the data from the Auto-Scan populate the Comments field after you paste.
Click the [Send Email!] that is below the Comments box once the form is filled out.
The Ross-Tech support team will reply back once we have an answer to provide. We also have a Ross-Tech Forum where you should post your scan and questions:
https://forums.ross-tech.com/index.php
That is the best place to get help from the greatest variety of different people, in a place where answers will be searchable in the future as well.