Difference between revisions of "Immobilizer I Key Matching (Separate)"
From Ross-Tech Wiki
RtWiKiSyS0p (talk | contribs) m |
|||
| (9 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
__FORCETOC__ | __FORCETOC__ | ||
| − | '''This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with with Immobilizer | + | '''This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with with Immobilizer I, where the immobilizer control module is integrated in a separate immo box. See the seperate instructions for models where the [[Immobilizer I Key Matching (Cluster)|immobilizer control module is integrated in instrument cluster]].''' |
== Determining IMMO-ID & VIN == | == Determining IMMO-ID & VIN == | ||
| Line 6: | Line 6: | ||
'''[Select]'''<br> | '''[Select]'''<br> | ||
'''[25 - Immobilizer]'''<br> | '''[25 - Immobilizer]'''<br> | ||
| − | Look at the | + | Look at the "Component" field. The 14-digit string in the Immo-ID.<br> |
'''[Close Controller, Go Back - 06]'''<br> | '''[Close Controller, Go Back - 06]'''<br> | ||
| Line 25: | Line 25: | ||
'''[Go!]'''<br> | '''[Go!]'''<br> | ||
''The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.''<br> | ''The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.''<br> | ||
| − | ''You can check each key in this manner.'' | + | ''You can check each key in this manner.''<br> |
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
'''[Login - 11]'''<br> | '''[Login - 11]'''<br> | ||
| − | |||
* '''4-digit PIN''' | * '''4-digit PIN''' | ||
** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.'' | ** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.'' | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
'''[Do it!]'''<br> | '''[Do it!]'''<br> | ||
| Line 46: | Line 40: | ||
''The "Stored Value" is the number of keys currently matched.''<br> | ''The "Stored Value" is the number of keys currently matched.''<br> | ||
Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.<br> | Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.<br> | ||
| − | ''The old keys are automatically | + | ''The old keys are automatically being cleared.''<br> |
'''[Save]'''<br> | '''[Save]'''<br> | ||
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
'''[Close Controller, Go Back - 06]'''<br> | '''[Close Controller, Go Back - 06]'''<br> | ||
| − | * ''Repeat the following steps until all | + | * ''Repeat the following steps until all Keys have been matched:'' |
| − | **''Switch | + | **''Switch Ignition OFF and remove Key.'' |
| − | **''Insert next | + | **''Insert the next Key and switch Ignition ON.'' |
| − | **''The | + | **''The Immobilizer Warning Light will light up for ~2 seconds, wait until it goes out.'' |
'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!'' | '''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!'' | ||
Latest revision as of 16:26, 12 July 2012
This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with with Immobilizer I, where the immobilizer control module is integrated in a separate immo box. See the seperate instructions for models where the immobilizer control module is integrated in instrument cluster.
Determining IMMO-ID & VIN
[Select]
[25 - Immobilizer]
Look at the "Component" field. The 14-digit string in the Immo-ID.
[Close Controller, Go Back - 06]
Key Matching
Prerequisites:
- All keys are either new or were adapted to this car (IMMO-ID) before.
- You can match up to 4 keys.
- While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). The passenger seat is an adequate place.
- Battery voltage at least 12.0 V.
[Select]
[25 - Immobilizer]
[Meas. Blocks - 08]
Select Block 001.
[Go!]
The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.
You can check each key in this manner.
[Done, Go Back]
[Login - 11]
- 4-digit PIN
- Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234.
[Do it!]
[Adaptation - 10]
Enter 01 in "Channel Number".
[Read]
The "Stored Value" is the number of keys currently matched.
Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.
The old keys are automatically being cleared.
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]
- Repeat the following steps until all Keys have been matched:
- Switch Ignition OFF and remove Key.
- Insert the next Key and switch Ignition ON.
- The Immobilizer Warning Light will light up for ~2 seconds, wait until it goes out.
Note: The above steps after saving the adaptation, should not exceed 60 seconds!