Difference between revisions of "Immobilizer III Injection Pump Swapping"
From Ross-Tech Wiki
RtWiKiSyS0p (talk | contribs) m |
|||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 27: | Line 27: | ||
'''<u>Prerequisites:</u>'''<br> | '''<u>Prerequisites:</u>'''<br> | ||
| − | * The NEW | + | * The NEW Injection Pump is installed in the car. |
* Battery voltage at least 12.5 V. | * Battery voltage at least 12.5 V. | ||
* Make sure to have the Immobilizer PIN, for the Engine Control Unit (ECU). | * Make sure to have the Immobilizer PIN, for the Engine Control Unit (ECU). | ||
| Line 37: | Line 37: | ||
'''[Login - 11]'''<br> | '''[Login - 11]'''<br> | ||
| − | |||
* '''4-digit PIN''' | * '''4-digit PIN''' | ||
** The PIN needs to be entered as 5-digit number. ''For example, if your PIN is 1234, enter 01234.'' | ** The PIN needs to be entered as 5-digit number. ''For example, if your PIN is 1234, enter 01234.'' | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
'''[Do it!]'''<br> | '''[Do it!]'''<br> | ||
| Line 51: | Line 45: | ||
Enter 050 in "Channel Number".<br> | Enter 050 in "Channel Number".<br> | ||
'''[Read]'''<br> | '''[Read]'''<br> | ||
| − | |||
* '''4-digit PIN''' | * '''4-digit PIN''' | ||
** The PIN needs to be entered as 5-digit number. ''For example, if your PIN is 1234, enter 01234.'' | ** The PIN needs to be entered as 5-digit number. ''For example, if your PIN is 1234, enter 01234.'' | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
'''[Save]'''<br> | '''[Save]'''<br> | ||
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
Latest revision as of 16:39, 12 July 2012
This procedure details how to change the Injection Pump on 2.5l V6 TDI Engine in VW/Audi/Seat/Skoda vehicles with Immobilizer III.
Determining VIN & IMMO-ID
Engine Control Unit (ECU)
[Select]
[01 - Engine]
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.
[Close Controller, Go Back - 06]
---OR---
[Select]
[01 - Engine]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]
Injection Pump Swapping
Prerequisites:
- The NEW Injection Pump is installed in the car.
- Battery voltage at least 12.5 V.
- Make sure to have the Immobilizer PIN, for the Engine Control Unit (ECU).
[Select]
[01 - Engine]
[Login - 11]
- 4-digit PIN
- The PIN needs to be entered as 5-digit number. For example, if your PIN is 1234, enter 01234.
[Do it!]
[Adaptation - 10]
Enter 050 in "Channel Number".
[Read]
- 4-digit PIN
- The PIN needs to be entered as 5-digit number. For example, if your PIN is 1234, enter 01234.
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]
- Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
- Start the Engine to verify the adaptation was successful.