01487: Difference between revisions
From Ross-Tech Wiki
Table Of Contents
-
1.
01487 - System Function Test
-
1.1.1
01487 - System Function Test
- 1.1.1.2 Possible Symptoms
- 1.1.2.2 Possible Causes
- 1.1.3.2 Possible Solutions
- 1.1.4.2 Special Notes
-
1.2.1
01487 - System Function Test: Implausible Signal
- 1.2.1.7 Possible Symptoms
- 1.2.2.7 Possible Causes
- 1.2.3.7 Special Notes
-
1.1.1
01487 - System Function Test
RtWiKiSyS0p (talk | contribs) New page: __FORCETOC__ == 01487 - System Function Test == === 01487 - System Function Test: Implausible Signal === ==== Possible Symptoms ==== * Malfunction Indicator Light (MIL) ON ==== Possibl... |
|||
| (8 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
__FORCETOC__ | __FORCETOC__ | ||
== 01487 - System Function Test == | == 01487 - System Function Test == | ||
=== 01487 - System Function Test === | |||
==== Possible Symptoms ==== | |||
* Malfunction Indicator Light (MIL) ON | |||
==== Possible Causes ==== | |||
* When found in Brake Electronics Control Module (J104) | |||
** Brake Electronics Function Test Timed Out | |||
==== Possible Solutions ==== | |||
* When found in Brake Electronics Control Module (J104) | |||
** Perform [[ESP System Function Test|Brake Electronics Function Test]] | |||
==== Special Notes ==== | |||
* When found in Brake Electronics Control Module (J104) | |||
** The Function Test on most ABS/ESP Systems should not exceed more than 50 Seconds | |||
=== 01487 - System Function Test: Implausible Signal === | === 01487 - System Function Test: Implausible Signal === | ||
| Line 10: | Line 31: | ||
==== Possible Causes ==== | ==== Possible Causes ==== | ||
* Internal Error in Control Module for Level Control (J197) | * When found in Control Module for Level Control (J197) | ||
* Control Module for Level Control (J197) faulty | ** Internal Error in Control Module for Level Control (J197) | ||
** Control Module for Level Control (J197) faulty | |||
==== Special Notes ==== | ==== Special Notes ==== | ||
* When found in [[Audi A8 (4E)], this Fault Code can have several different | * When found in [[Audi A8 (4E)]] or Bentley Continental (3W): Level Control (J197), this Fault Code can have several different Causes but by clearing Fault Codes most of those will be reset. Switch OFF the Ignition for 5 Seconds and then switch it back ON again, now clear Fault Codes and re-check for Fault Codes. If no Fault Code remains you are done. If the fault code remains, switch OFF the Ignition for 5 Seconds again and then switch it back ON. Now wait 5 Minutes before re-checking for Fault Codes! If after these 5 Minutes the Fault Code remains you may need to replace the Control Module for Level Control (J197). | ||
* When found in 8P HVAC (possibly others), this thread may be helpful: http://forums.ross-tech.com/showthread.php?6641/page3 | |||
[[Category:Fault Codes]] | [[Category:Fault Codes]] | ||
Latest revision as of 20:34, 26 October 2020
01487 - System Function Test
01487 - System Function Test
Possible Symptoms
- Malfunction Indicator Light (MIL) ON
Possible Causes
- When found in Brake Electronics Control Module (J104)
- Brake Electronics Function Test Timed Out
Possible Solutions
- When found in Brake Electronics Control Module (J104)
- Perform Brake Electronics Function Test
Special Notes
- When found in Brake Electronics Control Module (J104)
- The Function Test on most ABS/ESP Systems should not exceed more than 50 Seconds
01487 - System Function Test: Implausible Signal
Possible Symptoms
- Malfunction Indicator Light (MIL) ON
Possible Causes
- When found in Control Module for Level Control (J197)
- Internal Error in Control Module for Level Control (J197)
- Control Module for Level Control (J197) faulty
Special Notes
- When found in Audi A8 (4E) or Bentley Continental (3W): Level Control (J197), this Fault Code can have several different Causes but by clearing Fault Codes most of those will be reset. Switch OFF the Ignition for 5 Seconds and then switch it back ON again, now clear Fault Codes and re-check for Fault Codes. If no Fault Code remains you are done. If the fault code remains, switch OFF the Ignition for 5 Seconds again and then switch it back ON. Now wait 5 Minutes before re-checking for Fault Codes! If after these 5 Minutes the Fault Code remains you may need to replace the Control Module for Level Control (J197).
- When found in 8P HVAC (possibly others), this thread may be helpful: http://forums.ross-tech.com/showthread.php?6641/page3