Latest revision as of 22:43, 7 November 2025

0BK Transmission (ZF 8HP-55) – Standstill Basic Settings

Application

This procedure performs the Fast adaptation (standstill adaptation) routine for the ZF 0BK 8-speed automatic transmissions with UDS-based control modules.

Note: Not all 0BK transmission controllers support this function.

Prerequisites

Vehicle stationary, engine idling.
Parking brake applied and foot brake held firmly during the entire procedure.
Selector lever in D.
Transmission fluid temperature between 50 °C and 95 °C
Battery charger/maintainer connected.
No fault codes related to transmission or engine torque request.

When to Perform

After mechatronic unit replacement
After clutch or internal transmission repair
After ATF service
When experiencing harsh or irregular shifting

Procedure

[Select] → [02-Auto Trans] [Basic Settings - UDS]

From the Basic Settings drop-down list, select Fast/Quick Adaption (IDE07217)
Click [Show Measuring Data] and add:

 - Engine speed (IDE00021)
 - Fast_adaption; cancellation condition (IDE07220)
 - ATF temperature (IDE00024)

Apply the parking brake, hold the brake pedal, and move the selector from [P] to [D]
Press [Go!] to start the Basic Setting.

During the Procedure

Engine speed will increase to about 1,200 rpm
Light jolts or lurching may occur; this is normal
The procedure typically runs for 5–10 minutes
Continue holding the brake; do not release!
Monitor ATF temperature remains within the specified range.

The Basic Setting may abort if:

Brake pedal is released or selector not in [D]
ATF temperature outside 50–95 °C
TCM not standstill-capable (engine speed does not rise to ~ 1,200 rpm)

Completion

When the procedure finishes (Finished correctly):

Engine speed returns to normal idle.
Shift selector to [P] when prompted.
Click [Done, Go Back]
Read and clear any fault codes if necessary.
Road test the vehicle, normally

Notes

Always confirm ATF level and temperature before performing adaptation.
Use official factory information if unsure whether the control module supports this function.

@@ Line 1: / Line 1: @@
-__NOTOC__
+= 0BK Transmission (ZF 8HP-55) – Standstill Basic Settings =
-__NOEDITSECTION__
+__FORCETOC__
-=== [01] - [[:Category:Engines|Engine Electronics]] ===
-==== [[:Category:Gasoline Engines|Gasoline Engines]] ====
-=== [02] - [[:Category:Transmissions|Transmission Electronics]] ===
+== Application ==
-=== [03] - Brake Electronics ===
+This procedure performs the '''Fast adaptation''' (standstill adaptation) routine for the ZF 0BK 8-speed automatic transmissions with UDS-based control modules.
-* [[Bentley Continental (3W) Brake Electronics (Bosch 5.7)|Bosch 5.7]]
+''Note: Not all 0BK transmission controllers support this function.''
-** [[Bentley Continental (3W) Brake Electronics (Bosch 5.7)#Coding II|Coding II]]
-** [[Bentley Continental (3W) Brake Electronics (Bosch 5.7)#Coding|Coding]]
-** [[Bentley Continental (3W) Brake Electronics (Bosch 5.7)#Basic Setting|Basic Setting]]
-** Label File ''(3W0-614-517.LBL)''
-* [[Bentley Continental (3W) Brake Electronics (Bosch 8.1)|Bosch 8.1]]
-** [[Bentley Continental (3W) Brake Electronics (Bosch 8.1)#Coding|Coding]]
-** [[Bentley Continental (3W) Brake Electronics (Bosch 8.1)#Basic Setting|Basic Setting]]
-** [[Bentley Continental (3W) Brake Electronics (Bosch 8.1)#Replacement|Replacement]]
-** Label File ''(3W0-614-511.CLB)''
-=== [05] - Access/Start Authorization ===
+== Prerequisites ==
-=== [06] - Seat Adjustment (Passenger) ===
+* Vehicle stationary, engine idling.
-=== [09] - Central Electronics ===
+* Parking brake applied and foot brake held firmly during the entire procedure.
-=== [13] - Distance Regulation ===
+* Selector lever in '''D'''.
-=== [15] - Airbag ===
+* Transmission fluid temperature between '''50 °C and 95 °C'''
-=== [16] - Steering Wheel Electronics ===
+* Battery charger/maintainer connected.
-=== [17] - Instrument Cluster ===
+* No fault codes related to transmission or engine torque request.
-=== [18] - Auxiliary Heating ===
-=== [19] - CAN-Gateway ===
-=== [22] - All-Wheel-Drive ===
-=== [28] - Heating/Air Conditioning (Rear) ===
-=== [29] - Headlight Aim Control Left ===
-=== [34] - Level Control ===
-=== [36] - Seat Adjustment (Driver) ===
-=== [37] - Navigation ===
-=== [39] - Headlight Aim Control Right ===
-=== [46] - [[VW Golf (1K) Comfort System|Comfort System]] ===
+== When to Perform ==
+* After mechatronic unit replacement
+* After clutch or internal transmission repair
+* After ATF service
+* When experiencing harsh or irregular shifting
-* [[VW Golf (1K) Comfort System#Coding|Coding]]
+== Procedure ==
-* [[VW Golf (1K) Comfort System#Adaptation|Adaptation]]
+[Select] → [02-Auto Trans]
-* [[VW Golf (1K) Comfort System#Special Procedures|Special Procedures]]
+'''[Basic Settings - UDS]'''
-* [http://www.ross-tech.com/vag-com/download/label-files/1K0-959-433-46.lbl Label File]
+* From the Basic Settings drop-down list, select '''Fast/Quick Adaption (IDE07217)'''
+* Click '''[Show Measuring Data]''' and add:
+  - Engine speed (IDE00021)
+  - Fast_adaption; cancellation condition (IDE07220)
+  - ATF temperature (IDE00024)
+* Apply the parking brake, hold the brake pedal, and move the selector from '''[P]''' to '''[D]'''
+* Press '''[Go!]''' to start the Basic Setting.
-=== [16] - [[VW Touareg (7P) Steering Wheel Electronics|Steering Wheel Electronics]] ===
+=== During the Procedure ===
+* Engine speed will increase to about 1,200 rpm
+* Light jolts or lurching may occur; this is normal
+* The procedure typically runs for 5–10 minutes
+* Continue holding the brake; do not release!
+* Monitor ATF temperature remains within the specified range.
-* [[VW Touareg (7P) Steering Wheel Electronics#Coding|Coding]]
+=== The Basic Setting may abort if: ===
-* [[VW Touareg (7P) Steering Wheel Electronics#Adaptation|Adaptation]]
+* Brake pedal is released or selector not in [D]
-* [[VW Touareg (7P) Steering Wheel Electronics#Special Procedures|Special Procedures]]
+* ATF temperature outside 50–95 °C
+* TCM not standstill-capable (engine speed does not rise to ~ 1,200 rpm)
+== Completion ==
+When the procedure finishes '''(Finished correctly)''':
+* Engine speed returns to normal idle.
+* Shift selector to '''[P]''' when prompted.
+* Click '''[Done, Go Back]'''
+* Read and clear any fault codes if necessary.
+* Road  test the vehicle, normally
+== Notes ==
+* Always confirm ATF level and temperature before performing adaptation.
+* Use official factory information if unsure whether the control module supports this function.
-=== [47] - Sound System ===
-=== [53] - [[Bentley Continental (3W) Parking Brake|Parking Brake]] ===
-* [[Bentley Continental (3W) Parking Brake#Coding|Coding]]
-* [[Bentley Continental (3W) Parking Brake#Adaptation|Adaptation]]
-* [[Bentley Continental (3W) Parking Brake#Basic Setting|Basic Setting]]
-* [[Bentley Continental (3W) Parking Brake#Replacement|Replacement]]
-* Label File ''(3W0-907-801.CLB)''
-=== [55] - Headlight Aim Control ===
-=== [56] - Radio (Analog) ===
-=== [57] - TV-Tuner ===
-=== [65] - [[Bentley Continental (3W) Tire Pressure Monitoring|Tire Pressure Monitoring]] ===
-* [[Bentley Continental (3W) Tire Pressure Monitoring#Coding|Coding]]
-* [[Bentley Continental (3W) Tire Pressure Monitoring#Special Procedures|Special Procedures]]
-* Label File
-=== [68] - Wiper Electronics ===
-=== [69] - Trailer ===
-=== [6C] - [[Bentley Continental (3W) Back-Up Camera|Back-Up Camera]] ===
-* [[Bentley Continental (3W) Back-Up Camera#Coding|Coding]]
-* [[Bentley Continental (3W) Back-Up Camera#Security Access|Security Access]]
-* [[Bentley Continental (3W) Back-Up Camera#Special Procedures|Special Procedures]]
-* Label File ''(5N0-907-441.CLB)''
-=== [76] - Parking Aid ===
-=== [77] - Telephone ===

User:Peter: Difference between revisions

Namespaces

Views

More

Table Of Contents