User:Peter: Difference between revisions

From Ross-Tech Wiki
← Older edit
Peter (talk | contribs)
508 edits
No edit summary
Peter (talk | contribs)
508 edits
No edit summary
 
(32 intermediate revisions by 3 users not shown)
Line 1: Line 1:
__NOTOC__
= 0BK Transmission (ZF 8HP-55) – Standstill Basic Settings =
__NOEDITSECTION__
__FORCETOC__


== Application ==
This procedure performs the '''Fast adaptation''' (standstill adaptation) routine for the ZF 0BK 8-speed automatic transmissions with UDS-based control modules.


''Note: Not all 0BK transmission controllers support this function.''


== '''VW Scirocco (13)''' ==
== Prerequisites ==
* Vehicle stationary, engine idling. 
* Parking brake applied and foot brake held firmly during the entire procedure. 
* Selector lever in '''D'''. 
* Transmission fluid temperature between '''50 °C and 95 °C'''
* Battery charger/maintainer connected. 
* No fault codes related to transmission or engine torque request.


== When to Perform ==
* After mechatronic unit replacement 
* After clutch or internal transmission repair 
* After ATF service 
* When experiencing harsh or irregular shifting


=== [01] - [[:Category:Engines|Engine Electronics]] ===
== Procedure ==
==== [[:Category:Gasoline Engines|Gasoline Engines]] ====
[Select] → [02-Auto Trans]
==== [[:Category:Diesel Engines|Diesel Engines]] ====
'''[Basic Settings - UDS]'''
=== [02] - [[:Category:Transmissions|Transmission Electronics]] ===
 
=== [03] - Brake Electronics ===
* From the Basic Settings drop-down list, select '''Fast/Quick Adaption (IDE07217)'''
=== [08] - Heating/Air Conditioning ===
* Click '''[Show Measuring Data]''' and add:
=== [0F] - Radio (Digital) ===
  - Engine speed (IDE00021)
=== [09] - Central Electronics|Central Electronics ===
  - Fast_adaption; cancellation condition (IDE07220)
=== [14] - Suspension Electronics  ===
  - ATF temperature (IDE00024)
=== [15] - Airbag ===
* Apply the parking brake, hold the brake pedal, and move the selector from '''[P]''' to '''[D]''' 
=== [16] - Steering wheel ===
* Press '''[Go!]''' to start the Basic Setting.
=== [17] - Instrument Cluster|Instrument Cluster ===
 
=== [19] - CAN-Gateway|CAN-Gateway ===
=== During the Procedure ===
=== [22] - All-Wheel-Drive ===
* Engine speed will increase to about 1,200 rpm 
=== [25] - Immobilizer ===
* Light jolts or lurching may occur; this is normal
=== [2E] - Media Player 3 ===
* The procedure typically runs for 5–10 minutes
=== [37] - Navigation ===
* Continue holding the brake; do not release!
=== [42] - Door Electronics Driver ===
* Monitor ATF temperature remains within the specified range.
=== [44] - Steering Assist ===
 
=== [46] - Comfort System ===
=== The Basic Setting may abort if: ===
=== [47] - Sound System ===
* Brake pedal is released or selector not in [D]  
=== [4C] - Tire Pressure Monitoring II ===
* ATF temperature outside 50–95 °C  
=== [52] - Door Electronics Passenger ===
* TCM not standstill-capable (engine speed does not rise to ~ 1,200 rpm)
=== [55] - Headlight Aim Control ===
 
=== [56] - VW Radio/Navigation System|Radio ===
== Completion ==
When the procedure finishes '''(Finished correctly)''':
* Engine speed returns to normal idle. 
* Shift selector to '''[P]''' when prompted. 
* Click '''[Done, Go Back]''' 
* Read and clear any fault codes if necessary.
* Road test the vehicle, normally
 
== Notes ==
* Always confirm ATF level and temperature before performing adaptation.  
* Use official factory information if unsure whether the control module supports this function.

Latest revision as of 22:43, 7 November 2025

0BK Transmission (ZF 8HP-55) – Standstill Basic Settings

Application

This procedure performs the Fast adaptation (standstill adaptation) routine for the ZF 0BK 8-speed automatic transmissions with UDS-based control modules.

Note: Not all 0BK transmission controllers support this function.

Prerequisites

  • Vehicle stationary, engine idling.
  • Parking brake applied and foot brake held firmly during the entire procedure.
  • Selector lever in D.
  • Transmission fluid temperature between 50 °C and 95 °C
  • Battery charger/maintainer connected.
  • No fault codes related to transmission or engine torque request.

When to Perform

  • After mechatronic unit replacement
  • After clutch or internal transmission repair
  • After ATF service
  • When experiencing harsh or irregular shifting

Procedure

[Select] → [02-Auto Trans] [Basic Settings - UDS]

  • From the Basic Settings drop-down list, select Fast/Quick Adaption (IDE07217)
  • Click [Show Measuring Data] and add:
 - Engine speed (IDE00021)
 - Fast_adaption; cancellation condition (IDE07220)
 - ATF temperature (IDE00024)
  • Apply the parking brake, hold the brake pedal, and move the selector from [P] to [D]
  • Press [Go!] to start the Basic Setting.

During the Procedure

  • Engine speed will increase to about 1,200 rpm
  • Light jolts or lurching may occur; this is normal
  • The procedure typically runs for 5–10 minutes
  • Continue holding the brake; do not release!
  • Monitor ATF temperature remains within the specified range.

The Basic Setting may abort if:

  • Brake pedal is released or selector not in [D]
  • ATF temperature outside 50–95 °C
  • TCM not standstill-capable (engine speed does not rise to ~ 1,200 rpm)

Completion

When the procedure finishes (Finished correctly):

  • Engine speed returns to normal idle.
  • Shift selector to [P] when prompted.
  • Click [Done, Go Back]
  • Read and clear any fault codes if necessary.
  • Road test the vehicle, normally

Notes

  • Always confirm ATF level and temperature before performing adaptation.
  • Use official factory information if unsure whether the control module supports this function.
Retrieved from "https://wiki.ross-tech.com/wiki/index.php?title=User:Peter&oldid=9803"
Contact Privacy Accessibility