Difference between revisions of "User:Jef"

From Ross-Tech Wiki
 
(26 intermediate revisions by the same user not shown)
Line 1: Line 1:
Page Title = Level Control, non UDS
+
== Contacting Ross-Tech  ==
  
This information applies to the [https://forums.ross-tech.com/index.php?threads/1905/ non UDS] Level Control.  This can be identified by evaluating the data in the Auto-Scan:
+
Blah blah blah, if additional assistance is needed, our registered customers can submit an auto-scan for review blah blah blah
  
Address 34: Level Control        Labels: 4E0-910-553.clb
+
Once the Auto-Scan is complete, click on the small VCDS icon in the top left corner, then select '''[Copy and Submit Auto-Scan]'''.
    Part No SW: 4E0 910 553 K    HW: 4E0 907 553 H
 
    Component: '''LUFTFDR.-CDC'''   H07 4590
 
  
Address 34: Level Control        Labels: 4F0-910-553.clb
+
https://i.imgur.com/XbVYS1j.jpg
    Part No SW: 4F0 910 553 A    HW: 4F0 907 553 A
 
    Component: '''J197 LUFTFEDER'''  H17 0060
 
  
*If '''LUFTFDR.-CDC''' or '''J197 LUFTFEDER''' is not shown in the Component field, this information may not apply.
 
  
 +
This will load up a special web page with a form to fill out.  Please verify you type in your correct email address.
  
 +
The Short Serial Number is on your Ross-Tech device, you will find that on the sticker.  It might be something like:
 +
* HN2-xxxxxx
 +
* H17-xxxxxx
 +
* HCxxxxxx
 +
* UCxxxxxx
  
 +
In the Comments box, document the issue or concern.  Once you have that typed out, in the Comment box, right click your mouse and then select '''[Paste]'''.
  
 +
https://i.imgur.com/OJLxxx8.jpeg
  
== Bleeding or Charging ==
+
https://i.imgur.com/5Wc30hQ.jpeg
Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk. As always, you should refer to a Factory Repair Manual for your vehicle!
 
  
'''<u>Prerequisites:</u>'''<br>
+
You should see the data from the Auto-Scan populate the Comments field after you paste.
*Doors, hood and rear lid closed
 
*Engine at idle
 
  
Note: The bleeding procedure will lower the vehicle, proceed with caution and refer to the factory repair manual for proper repair information, warnings and cautions!
+
Click the '''[Send Email!]''' that is below the Comments box once the form is filled out.
  
'''[Select]'''<br>
+
The Ross-Tech support team will reply back once we have an answer to provide.  We also have a Ross-Tech Forum where you should post your scan and questions:
'''[34-Level Control]'''<br>
 
'''[Security Access-16]'''<br>
 
Enter 08367
 
* If the Security Access code does not work, try 08367 in '''[Coding II - 11]'''
 
  
'''[Basic Settings-04]'''<br>
+
'''https://forums.ross-tech.com/index.php'''
* Bleeding:
 
** Group 020 = to Bleed Pressure Accumulator<br>
 
** Group 021 = to Bleed Front Axle<br>
 
** Group 022 = to Bleed Rear Axle<br>
 
* Charging:
 
** Group 023 = to Charge Pressure Accumulator
 
** Group 024 = to Charge Front Axle
 
** Group 025 = to Charge Rear Axle
 
'''[Go!]'''<br>
 
'''[ON/OFF/Next]'''<br>
 
  
Field-4 will display the current pressure.<br>
+
That is the best place to get help from the greatest variety of different people, in a place where answers will be searchable in the future as well.
The procedure will time out after 60 seconds.<br>
 
The procedure maybe repeated as necessary to achieve the desired system pressure.
 
 
 
 
 
==== Special Notes ====
 
 
 
*These instructions should work with most non-UDS Level Control systems found in:
 
**A6
 
**A8
 
**Q7
 
**Phaeton
 
**Touareg
 
**Bentley Continental.
 
*http://forums.ross-tech.com/showthread.php?1996-Level-Control-Bleeding-Charging
 

Latest revision as of 15:35, 27 March 2025

Contacting Ross-Tech

Blah blah blah, if additional assistance is needed, our registered customers can submit an auto-scan for review blah blah blah

Once the Auto-Scan is complete, click on the small VCDS icon in the top left corner, then select [Copy and Submit Auto-Scan].

XbVYS1j.jpg


This will load up a special web page with a form to fill out. Please verify you type in your correct email address.

The Short Serial Number is on your Ross-Tech device, you will find that on the sticker. It might be something like:

  • HN2-xxxxxx
  • H17-xxxxxx
  • HCxxxxxx
  • UCxxxxxx

In the Comments box, document the issue or concern. Once you have that typed out, in the Comment box, right click your mouse and then select [Paste].

OJLxxx8.jpeg

5Wc30hQ.jpeg

You should see the data from the Auto-Scan populate the Comments field after you paste.

Click the [Send Email!] that is below the Comments box once the form is filled out.

The Ross-Tech support team will reply back once we have an answer to provide. We also have a Ross-Tech Forum where you should post your scan and questions:

https://forums.ross-tech.com/index.php

That is the best place to get help from the greatest variety of different people, in a place where answers will be searchable in the future as well.