Difference between revisions of "Audi A8 (4E) Parking Brake"
RtWiKiSyS0p (talk | contribs) m |
RtWiKiSyS0p (talk | contribs) |
||
| Line 1: | Line 1: | ||
__FORCETOC__ | __FORCETOC__ | ||
== Coding == | == Coding == | ||
| + | |||
| + | '''''Note''': When replacing this Control Module it is necessary to perform the Basic Settings [[#Function Test|Function Test (MVB 010)]] and [[#Longitudinal Acceleration Sensor (G251)|Longitudinal Acceleration Sensor (MVB 020)]] first. This sets a Readiness Bit for each of the Basic Settings, Coding will not be accepted without having done this first!''<br> | ||
| + | |||
| + | *'''0000?xx''': ''Engine'' | ||
| + | ** 1 = 3.0l MPI (Gasoline) | ||
| + | ** 2 = 3.0l TDI (Diesel) | ||
| + | ** 3 = 3.7l | ||
| + | ** 4 = 4.0l | ||
| + | ** 5 = 4.2l | ||
| + | ** 6 = 6.0l | ||
| + | *'''0000x?x''': ''Transmission'' | ||
| + | ** 1 = Multitronic (VL30) | ||
| + | ** 2 = Automatic Transmission (AL420) | ||
| + | ** 3 = Automatic Transmission (AL600) | ||
| + | *'''0000xx?''': ''Country'' | ||
| + | ** 1 = Rest of World (RoW) | ||
| + | ** 2 = USA/Canada | ||
| + | ** 3 = Japan | ||
| + | |||
== Adaptation == | == Adaptation == | ||
=== Pad Thickness === | === Pad Thickness === | ||
| Line 32: | Line 51: | ||
'''''Note:''' Check/change adaptation channel 006 ([[#Pad Thickness|Pad Thickness]]) after changing the pads.''<br><br> | '''''Note:''' Check/change adaptation channel 006 ([[#Pad Thickness|Pad Thickness]]) after changing the pads.''<br><br> | ||
| − | |||
=== Open Rear Parking Brake for Repairs === | === Open Rear Parking Brake for Repairs === | ||
| Line 47: | Line 65: | ||
'''[Close Controller, Go Back - 06]'''<br><br> | '''[Close Controller, Go Back - 06]'''<br><br> | ||
| − | |||
=== Close Rear Parking Brake === | === Close Rear Parking Brake === | ||
| Line 60: | Line 77: | ||
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
'''[Close Controller, Go Back - 06]'''<br><br> | '''[Close Controller, Go Back - 06]'''<br><br> | ||
| + | |||
| + | |||
| + | === Function Test === | ||
| + | '''<u>Prerequisites:</u>'''<br> | ||
| + | * Cycle the Parking Brake ON, then OFF first. | ||
| + | '''[Select]'''<br> | ||
| + | '''[53 - Parking Brake]'''<br> | ||
| + | '''[Basic Settings - 04]'''<br> | ||
| + | Group 010<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Activate the Basic Setting.<br> | ||
| + | '''[ON/OFF/Next]'''<br> | ||
| + | The brake pads are now opening and closing 3 times.<br> | ||
| + | Wait 30 seconds after the the brakes stop making noise.<br> | ||
| + | '''[Done, Go Back]'''<br> | ||
| + | '''[Close Controller, Go Back - 06]'''<br><br> | ||
| + | |||
| + | |||
| + | === Longitudinal Acceleration Sensor (G251) === | ||
| + | |||
| + | '''<u>Prerequisites:</u>'''<br> | ||
| + | * System voltage at least 12.0 V. | ||
| + | * Car parked on a level surface. | ||
| + | * Do NOT move/rock car while performing basic setting. | ||
| + | |||
| + | '''[Select]'''<br> | ||
| + | '''[53 - Parking Brake]'''<br> | ||
| + | '''[Basic Settings - 04]'''<br> | ||
| + | Group 020<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Activate the Basic Setting.<br> | ||
| + | '''[ON/OFF/Next]'''<br> | ||
| + | The status of the Longitudinal Acceleration Sensor (G251) is now beeing displayed.<br> | ||
| + | '''[Done, Go Back]'''<br> | ||
| + | |||
| + | |||
| + | == Special Procedures == | ||
| + | |||
| + | * [[Audi A8 (4E) Parking Brake Pad Replacement|Parking Brake Pad Replacement]] | ||
Revision as of 08:26, 27 July 2007
Coding
Note: When replacing this Control Module it is necessary to perform the Basic Settings Function Test (MVB 010) and Longitudinal Acceleration Sensor (MVB 020) first. This sets a Readiness Bit for each of the Basic Settings, Coding will not be accepted without having done this first!
- 0000?xx: Engine
- 1 = 3.0l MPI (Gasoline)
- 2 = 3.0l TDI (Diesel)
- 3 = 3.7l
- 4 = 4.0l
- 5 = 4.2l
- 6 = 6.0l
- 0000x?x: Transmission
- 1 = Multitronic (VL30)
- 2 = Automatic Transmission (AL420)
- 3 = Automatic Transmission (AL600)
- 0000xx?: Country
- 1 = Rest of World (RoW)
- 2 = USA/Canada
- 3 = Japan
Adaptation
Pad Thickness
[Select]
[53 - Parking Brake]
[Adaptation - 10]
Channel 006
[Read]
Enter the current thickness of the new pads (Range: 3 - 14 mm).
[Test]
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]
Basic Setting
Open Rear Parking Brake for Pad Change
[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 005
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake pads are now opening.
[Done, Go Back]
[Close Controller, Go Back - 06]
Note: Check/change adaptation channel 006 (Pad Thickness) after changing the pads.
Open Rear Parking Brake for Repairs
[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 007
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake pads are now opening.
[Done, Go Back]
[Close Controller, Go Back - 06]
Close Rear Parking Brake
[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 006
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake pads are now closing.
[Done, Go Back]
[Close Controller, Go Back - 06]
Function Test
Prerequisites:
- Cycle the Parking Brake ON, then OFF first.
[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 010
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake pads are now opening and closing 3 times.
Wait 30 seconds after the the brakes stop making noise.
[Done, Go Back]
[Close Controller, Go Back - 06]
Longitudinal Acceleration Sensor (G251)
Prerequisites:
- System voltage at least 12.0 V.
- Car parked on a level surface.
- Do NOT move/rock car while performing basic setting.
[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 020
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The status of the Longitudinal Acceleration Sensor (G251) is now beeing displayed.
[Done, Go Back]