Difference between revisions of "VW Passat (3C) Parking Brake"
RtWiKiSyS0p (talk | contribs) m |
|||
| Line 24: | Line 24: | ||
'''[ON/OFF/Next]'''<br> | '''[ON/OFF/Next]'''<br> | ||
The brake pads are now opening.<br> | The brake pads are now opening.<br> | ||
| + | '''''Important''''': Wait 30 seconds after the brakes stop moving before carrying out the next step.<br> | ||
| + | Due to a firmware problem in some modules, failure to wait can result in damage to the control module. <br> | ||
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
'''[Close Controller, Go Back - 06]'''<br><br> | '''[Close Controller, Go Back - 06]'''<br><br> | ||
| Line 39: | Line 41: | ||
'''[ON/OFF/Next]'''<br> | '''[ON/OFF/Next]'''<br> | ||
The brake pads are now closing.<br> | The brake pads are now closing.<br> | ||
| + | '''''Important''''': Wait 30 seconds after the brakes stop moving before carrying out the next step. <br> | ||
| + | Due to a firmware problem in some modules, failure to wait can result in damage to the control module.<br> | ||
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
'''[Close Controller, Go Back - 06]'''<br><br> | '''[Close Controller, Go Back - 06]'''<br><br> | ||
| Line 53: | Line 57: | ||
'''[ON/OFF/Next]'''<br> | '''[ON/OFF/Next]'''<br> | ||
The brake pads are now opening and closing 3 times.<br> | The brake pads are now opening and closing 3 times.<br> | ||
| + | '''''Important''''': Wait 30 seconds after the brakes stop moving before carrying out the next step.<br> | ||
| + | Due to a firmware problem in some modules, failure to wait can result in damage to the control module.<br> | ||
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
'''[Close Controller, Go Back - 06]'''<br><br> | '''[Close Controller, Go Back - 06]'''<br><br> | ||
Revision as of 12:26, 6 July 2007
Coding
- 0000010 = Parking Brake without Auto-Hold (North America)
- 0000011 = Parking Brake without Auto-Hold (Rest of World / PR-UH1)
- 0000012 = Parking Brake with Auto-Hold (Rest of World / PR-UH2)
- 0000013 = Parking Brake with Auto-Hold (North America)
Adaptation
Basic Setting
Open Rear Parking Brake
Prerequisites:
- Connect a battery charger.
- Cycle the Parking Brake ON, then OFF first.
[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 007
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake pads are now opening.
Important: Wait 30 seconds after the brakes stop moving before carrying out the next step.
Due to a firmware problem in some modules, failure to wait can result in damage to the control module.
[Done, Go Back]
[Close Controller, Go Back - 06]
Close Rear Parking Brake
Prerequisites:
- Connect a battery charger.
[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 006
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake pads are now closing.
Important: Wait 30 seconds after the brakes stop moving before carrying out the next step.
Due to a firmware problem in some modules, failure to wait can result in damage to the control module.
[Done, Go Back]
[Close Controller, Go Back - 06]
Function Test
[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 010
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake pads are now opening and closing 3 times.
Important: Wait 30 seconds after the brakes stop moving before carrying out the next step.
Due to a firmware problem in some modules, failure to wait can result in damage to the control module.
[Done, Go Back]
[Close Controller, Go Back - 06]
Longitudinal Acceleration Sensor (G251)
See Brake Electronics for details.