Difference between revisions of "6-Speed Direct Shift Gearbox (DSG/02E)"
RtWiKiSyS0p (talk | contribs) m |
RtWiKiSyS0p (talk | contribs) m |
||
| Line 1: | Line 1: | ||
== Basic Setting == | == Basic Setting == | ||
'''<u>Prerequisites:</u>'''<br> | '''<u>Prerequisites:</u>'''<br> | ||
| + | * ATF Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019. | ||
| + | * Selector Lever in P | ||
* Ignition ON | * Ignition ON | ||
| − | * Engine | + | * Engine ON (Idling) |
| − | * | + | * Brake Pedal operated (hold for the whole procedure) |
| + | * Throttle Pedal not operated | ||
'''''NOTE:''' Be sure to perform the following steps in the sequence shown, followed by the defined test drive.'' | '''''NOTE:''' Be sure to perform the following steps in the sequence shown, followed by the defined test drive.'' | ||
| Line 62: | Line 65: | ||
'''[ON/OFF/Next]'''<br> | '''[ON/OFF/Next]'''<br> | ||
| − | === Reset Values (ESP & Tip Cruise Control) === | + | === Reset Values (ESP & Tip Cruise Control Installation) === |
Group 069<br> | Group 069<br> | ||
Revision as of 10:16, 21 December 2006
Basic Setting
Prerequisites:
- ATF Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019.
- Selector Lever in P
- Ignition ON
- Engine ON (Idling)
- Brake Pedal operated (hold for the whole procedure)
- Throttle Pedal not operated
NOTE: Be sure to perform the following steps in the sequence shown, followed by the defined test drive.
[Select]
[02 - Transmission]
[Basic Settings - 04]
Transmission Tolerances (Enganged Calibration)
Group 061
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Transmission Tolerances (Synch. Point. Measurement)
Group 060
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Clutch Adaptation
Control Module Software Version < 0800:
Group 062
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Control Module Software Version >= 0800 :
Group 067
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (Clutch Safety Function)
Group 068
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (Pressure Adaptation)
Group 065
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (Steering Wheel Paddle Installation)
Group 063
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (ESP & Tip Cruise Control Installation)
Group 069
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
[Done, Go Back]
[Fault Codes - 02]
Check and clear fault codes after successful test.
[Close Controller, Go Back - 06]
Perform the Defined Test Drive.
Special Procedures
Defined Test Drive
Suggested test drive after replacing the mechatronic or successful basic setting.
Prerequisites:
- ATF Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019.
Drive in Tiptronic Mode from stand still up to 6th Gear.
While doing that make sure to drive in Gears 3 or 5 for approx. 5 minutes and also in 4 or 6 for approx. 5 minutes.
The engine speed window for all gears is 1200 - 3500 RPM (for clutch calibration).
Perform one sharp braking followed by a full throttle acceleration (oil return check).
Evaluate creep and starting-off points.
Check for leaks.
NOTE: If the test drive cannot be performed in the recommended way or the necessary time, any remaining adaptations will be performed automatically during normal driving.