Difference between revisions of "User:Jef"
| Line 13: | Line 13: | ||
*If '''LUFTFDR.-CDC''' or '''J197 LUFTFEDER''' is not shown in the Component field, this information may not apply. | *If '''LUFTFDR.-CDC''' or '''J197 LUFTFEDER''' is not shown in the Component field, this information may not apply. | ||
| + | ==Suspension Level Control Calibration== | ||
| + | '''Prerequisites''' | ||
| + | * Engine at idle | ||
| + | * Transmission in park/neutral | ||
| + | * Doors, hood, rear lid or hatch are to remain shut during the entire procedure | ||
| − | + | '''[Select]'''<br> | |
| + | '''[34 - Level Control]'''<br> | ||
| + | '''[Security Access - 16]'''<br> | ||
| + | * Enter 31564 | ||
| + | '''[Do It!]'''<br> | ||
| + | '''[Adaption - 10]'''<br> | ||
| + | * Channel 01 | ||
| + | '''[Read]'''<br> | ||
| + | The vehicle will now try to level itself. The first field will show "Wait". Once this process is complete, the first field will show "Value".<br> | ||
| + | Now measure the ride height, in millimeters, from the center of the wheel to the edge of fender, do this for all four wheels and record the values.<br> | ||
| + | https://www.ross-tech.com/vag-com/cars/images/rim.jpeg | ||
| + | <br> | ||
| + | In the "New Value" field for channel 01, input the measurement from the left front wheel. | ||
| + | '''[Test]'''<br> | ||
| + | '''[Save]'''<br> | ||
| + | Confirm '''[Yes]'''<br> | ||
Revision as of 16:59, 17 July 2024
Page Title = Level Control, non UDS
This information applies to the non UDS Level Control. This can be identified by evaluating the data in the Auto-Scan:
Address 34: Level Control Labels: 4E0-910-553.clb Part No SW: 4E0 910 553 K HW: 4E0 907 553 H Component: LUFTFDR.-CDC H07 4590
Address 34: Level Control Labels: 4F0-910-553.clb Part No SW: 4F0 910 553 A HW: 4F0 907 553 A Component: J197 LUFTFEDER H17 0060
- If LUFTFDR.-CDC or J197 LUFTFEDER is not shown in the Component field, this information may not apply.
Suspension Level Control Calibration
Prerequisites
- Engine at idle
- Transmission in park/neutral
- Doors, hood, rear lid or hatch are to remain shut during the entire procedure
[Select]
[34 - Level Control]
[Security Access - 16]
- Enter 31564
[Do It!]
[Adaption - 10]
- Channel 01
[Read]
The vehicle will now try to level itself. The first field will show "Wait". Once this process is complete, the first field will show "Value".
Now measure the ride height, in millimeters, from the center of the wheel to the edge of fender, do this for all four wheels and record the values.
In the "New Value" field for channel 01, input the measurement from the left front wheel.
[Test]
[Save]
Confirm [Yes]
Bleeding or Charging
Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk. As always, you should refer to a Factory Repair Manual for your vehicle!
Prerequisites:
- Doors, hood and rear lid closed
- Engine at idle
Note: The bleeding procedure will lower the vehicle, proceed with caution and refer to the factory repair manual for proper repair information, warnings and cautions!
[Select]
[34-Level Control]
[Security Access-16]
Enter 08367
- If the Security Access code does not work, try 08367 in [Coding II - 11]
[Basic Settings-04]
- Bleeding:
- Group 020 = to Bleed Pressure Accumulator
- Group 021 = to Bleed Front Axle
- Group 022 = to Bleed Rear Axle
- Group 020 = to Bleed Pressure Accumulator
- Charging:
- Group 023 = to Charge Pressure Accumulator
- Group 024 = to Charge Front Axle
- Group 025 = to Charge Rear Axle
[Go!]
[ON/OFF/Next]
Field-4 will display the current pressure.
The procedure will time out after 60 seconds.
The procedure maybe repeated as necessary to achieve the desired system pressure.
Special Notes
- These instructions should work with most non-UDS Level Control systems found in:
- A6
- A8
- Q7
- Phaeton
- Touareg
- Bentley Continental.
- http://forums.ross-tech.com/showthread.php?1996-Level-Control-Bleeding-Charging